Hey BOOT! Good to see ya.

Really like that LPS Tapmatic2, works great for aluminum. Alum melts at low temp and likes to friction weld onto tooling. Worked great, even with that cheap dull hardware store tap

You should watch a few other videos on KZbin to see why yours doesn't work

Junkyard prices have doubled or even tripled in my area since the pandemic, so building this car yourself probably would have cost a lot more than what you paid. Junkyards here don’t let LS engines go out to the yard anymore, they get pulled immediately and put on a pallet with a stupid high price tag.

Really nice of Santa Clause to help push those vehicles around!

This is out of order, also kinda made too many clips and decided to make the water pump mod a vid of it's own. I'll finish editing it soon

Hey... heard your comment about problems with ""Mice"...saw this Short that might come in handy... kzbin.infoz0Rh6S8tgxw?si=VgxmIm7KNAv1MSxt

Good luck!

Kinda out of order but figured it would be nice to post this Details vid first. Also my shotgun mic normally does good but should of used a lav mic i guess, oh well. Last vid when i got the Firebird kzbin.info/www/bejne/q362ZpV-rcaZe9E

Fill the tube with sand

Damn, they cut the cowl and wipers out just to fit that truck intake?! I get being on a budget, but sometimes a spending a few bucks for the right part is worth it.

Still gotta edit the next vid or two, not sure how those clips will work out yet

You know, I got FOUR of these after loving the results of the small ones in my AC closet. It pulled out so much moisture, and I could tell how much it was helping my breathing. I upgrade to one of these in the closet, and man- it's like it's grabbing nothing. What am I doing wrong, because yours is obviously working for you.

I have the 12 inch same model shown in this video ..need to know can i replace the led light when it stops working and how to open it ..what size led i need to getv..please let me know or make another video drop to help us out ..

Closer cyl to the radiator seem to seal better.

I had mine for 2 years and I love it. It don't look original anymore lol

You get what you pay for. By the time you get them straightened out, you could have spent a little more $ and bought name brand heads that are proven to be good.

I cant find a soft nylon wheel like that. Got a link where I can get one?

i'm glad i realized my mistake before fully torquing down my headbolts that these washers had a chamfered side it's very easy to brush past it. torqued the first few in pattern one set to 100ft-lbs and glad i didn't fully do it because i had to take them out to make sure they're all set because it says if the chamfered side isn't on the bolt it'll cause premature bolt failure. also second thing i saw is that ARP has they're own specific torquing specs which i've heard horror stories about people who either didn't put washers on or torqued the bolts down to manufacture specific rather than ARP specific. they state to do 3 rounds of torquing the bolts to 100ft-lbs so i've been using a torque stick rated to 100ft-lbs to add that last layer of your "cover your ass" method

The magnet shown are inexpensive and reusable, great idea.

how do you torque down the new stud?

Is this original battery still alive?

Scotty Kilmer debunked the magnet scam.

You should add a front e bike wheel kit to it, and let us know how it is. If you still have the bike.

useless video

I have this bike, works fine, for $150 its a steal, runs and rides perfect. I love it

snake oil for your car. there is a reason an oil filter has a FILTER inside it

Your oil is extremely dark for just over 3,000 miles. Dark oil with such low miles usually indicates excessive wear.

you could use magnets w/o the metal ring, and silicone the magnet to the filter canister. I think some manufacturers put magnets in the oil pan.

Hey does anyone think i could use a grinder or electric chainsaw? To cut this up

I think any magnet would help collecting any metal with the filtration media. Unless it's not metallic. I seen magnet oil pan drain bolts too.

😂

I had some GE ones do that. They didn't burn as bad, but they stonk

2 yrs later get any satisfaction from this? Id be super pissed off. Somebody screwed the pooch or took you for a fool figuring you wouldnt know.

Cheap junk, prxxxxucts also. Runners are known to be worse than stock. I dont know why people buy this stuff Small savings isnt worth the hassle. Buy american while we still got choices guys. Wont be pretty if they have a stronghold. We will just get more junk at twice the $.

it says , valve spacing moved .050 from stock. do you need to use special rockers?

The Elgin Cam, can you tell me the part number I might have the same one thanks

My new tach does NOT have any external switch for 4, 6 or 8 cylinders. How do I change that?

Does the bulb get hot

Love this video. I plan on using one of these and if I film the project, I will give you a shout out, man. You're like a goofy steve magnante!! I love it!

test spark. that's the important. not the tale.

Ohh god! The porn music in the background 😂😂😂

It does indeed work.

if you want to get oil out poke a hole in bottom with a punch and then it will drain fully out the bottom

Boot!

Well, you can see where he magnet was and the stuff it collected. No denying it. Personally, I probably wouldn't run one. To me, if there's enough stuff collected by the magnet, you'd be able to see it in the filter media. Guess it'd save you the trouble of digging through an oily parts. Thanks for posting the vid. It was informative.

I am impressed with this method. I’m old school n I’ve never seen this done. I’m doing this

Realized while finishing up this vid. I need to cut LUCK's oil filter, before i get too into the mods. No more oil filter vids for now LOL Accessing LUCK kzbin.info/www/bejne/rXrIqGWtmZablbM

Thefe is no such thing as an ebay brand. PC would be procomp AKA speedmaster.