That number 2 injector looks lovely :) Fair play for getting it out. What's the make and model of Diagnostic tester that you use. I have the same sort of van, Thanks.
@PaulGrosvenor1Ай бұрын
Great helpful video. Did you have to adjust the hand brake?
@WebstersWorkshopАй бұрын
As long as someone hasn't adjusted the handbrake poorly before, no you shouldn't need to adjust the hand brake. The cable adjustment is just there to take the slack out of the cable, not to make it work better otherwise it's no different to driving with the handbrake on.
@chris0102812 ай бұрын
Are you ok? it's been a while
@WebstersWorkshop2 ай бұрын
@chris010281 yeah it's all good, just hot a few other projects on the go atm that need yo take priority over youtube.
@bowycolt21322 ай бұрын
How your gearbox going what you reckon would be wrong if it jumps out off third gear as your driving
@WebstersWorkshop2 ай бұрын
@bowycolt2132 sounds like 3rd gear syncro might be an issue. Any problems putting it in 3rd?
@bowycolt2132Ай бұрын
No it goes in ok just jumps out 1and 3 were did you get your gear parts from thanks @WebstersWorkshop
@WebstersWorkshopАй бұрын
@bowycolt2132 coastal motorhomes iirc they were fantastic, dropped them an email and told them what I needed and they came back with prices and part numbers.
@lEluSivl5 ай бұрын
Hey mate, awesome video by the way I can’t help but notice those awesome Rims you’ve got on your Calibra. Would you mind telling me what brand these are. I really want a set of 5 spoke 4 stud rims and these look appealing to me!
@WebstersWorkshop5 ай бұрын
Milli miglia can't remember yhe exact model. Don't think they make them anymore because I bought these back in the 90s to go on my nova.
@lEluSivl5 ай бұрын
@@WebstersWorkshop ahh fair enough, I’ll have to keep searching I have a Calibra myself and I’m sick of the rims that are on it.
@WebstersWorkshop5 ай бұрын
If you're on Facebook, search for a group called clubcalibra.net you might get some different rims on there
@lEluSivl5 ай бұрын
@@WebstersWorkshop thanks mate will do Again thanks for the video!
@equineeditsx60785 ай бұрын
what’s the exact size of the e8?
@WebstersWorkshop5 ай бұрын
What is the e8?
@equineeditsx60785 ай бұрын
the socket you used you get the actual motor out? i swear you said e8 lol
@WebstersWorkshop5 ай бұрын
Tbh it was that long ago, I really can't remember but if that's what I said, I just googled e8 sockets and they came up. It's like a female torx bit.
@craigmcguinness5 ай бұрын
Hi. Did u push snap the wipers back on as I changed mine yesterday and did so and the brand new mechanism snapped. Cheers in advance for your reply
@WebstersWorkshop5 ай бұрын
Push snap??? If your new linkage snapped then it sounds like an issue with the mechanism. I'd contact your supplier and see what they say.
@higherstandardspc5 ай бұрын
The best spray can shaker on youtube, Thank You ; ) Simplistic Design.
@mikeh51507 ай бұрын
Best idea for this that I've seen! Most contraptions I see on here are far too complicated.
@changluo8077 ай бұрын
My 2003 Relay gearbox has the similar issue. 4 out of 5 of those circlips have snapped, and the last one is very worn - It will snap soon if not replaced. I believe this is a design flaw, no idea why someone came up with such a poor design, simply awful!
@novasportregister86859 ай бұрын
Sound deadening will be a massive help when your in it and it’s raining! There’s a weigh bridge at Stannington!
@WebstersWorkshop9 ай бұрын
Apparently there's a 1 just over at glaxo.
@johnreed21229 ай бұрын
@WebstersWorkshop there's loads of weigh bridges at the scrap yards😂😂
@barryjackson85129 ай бұрын
Canny progress.
@WebstersWorkshop9 ай бұрын
Cheers. Would be faster if the weather was better.
@barryjackson85129 ай бұрын
@@WebstersWorkshop eye it’s against us now.
@madmaxxx97609 ай бұрын
How much does a job like this cost ?
@WebstersWorkshop9 ай бұрын
I have no idea bud, this is my wife's car and I did it myself. This is not a garage, it's just my workshop where I work on my own vehicles. All I can say is a good welder isn't cheap but a cheap welder isn't good.
@LukeImprob9 ай бұрын
Dont be fooled guys - those two whacks getting the ball joint out were the last two!
@danielstephenson8869 ай бұрын
Top tip Instead of clamping the flexy you can crack the bleed nipple or the pipe off then keep the brake pedal pushed down with a bar against the seat. You will get the first initial bit of fluid that comes out when you press the pedal but then it won't keep dripping. Ps callipers looking good 👍
@WebstersWorkshop9 ай бұрын
Cheers, will give that a try for the next time.
@martinkirton96089 ай бұрын
Great video as always !
@WebstersWorkshop9 ай бұрын
Thank you.
@barryjackson851210 ай бұрын
Come in
@WebstersWorkshop10 ай бұрын
🤣🤣
@richardgibson134710 ай бұрын
Finish the nova
@WebstersWorkshop10 ай бұрын
How's the welly?
@richardgibson134710 ай бұрын
@WebstersWorkshop closer to been finished than the nova. A couple more hours and there will be 6 months work left to do 🤣🤣🤣🤣🤣
@WebstersWorkshop10 ай бұрын
🤣🤣🤣
@smudgerart10 ай бұрын
Interesting. Signed up 👍 Did you lock the fuel pump or any other pulleys ? And what mileage do you recommend changing timing belt ?
@WebstersWorkshop10 ай бұрын
I didn't lock the pulleys, I was just really careful to keep the marks lined up when I refitted the new belt. I honestly have no idea how often they should be changed, the van is new to me so just changed it. At £150 for the whole kit it wasn't worth taking the risk.
@barryjackson851210 ай бұрын
Canny job. Did you not blank the EGR valve off?
@WebstersWorkshop10 ай бұрын
No the van is being built for miles and comfort, not speed. Truts me it goes against everything I'm about but this 1s different so needs a different t approach.
@Rotterdam9310 ай бұрын
Love calibra ❤
@WebstersWorkshop10 ай бұрын
Thank you.
@user-vu7lx5rs3f10 ай бұрын
Good job 👍
@WebstersWorkshop10 ай бұрын
Thank you.
@FlashBaz10 ай бұрын
Almost There 💪🏻
@WebstersWorkshop10 ай бұрын
Then the real fun begins fitting out the back end. 😁😁
@barryjackson851210 ай бұрын
Nice progress 😎
@WebstersWorkshop10 ай бұрын
I've already got the next 2 videos lined up. I'm way ahead of myself on this 1.
@Stoney3K11 ай бұрын
Pretty surprising that the ECU didn't set a P02AA code which is usually a tell tale sign of an injector on the way out. There's special slide hammer toolkits that screw on the injector fuel rail port if they're really stuck and you have to yank on them.
@WebstersWorkshop11 ай бұрын
It was the injector leaking internally which was dropping fuel pressure out of range. That's why it was showing fuel rail pressure sensor (I really hope this is the case anyway!😬) the injectors were still operating fine electronically. I'm not too sure that slide hammer would of worked in this case, the high pressure feed comes in the side of the injector, not the top. Thanks for the advise though. 😀
@Stoney3K11 ай бұрын
@@WebstersWorkshopI believe those injector puller slide hammer kits are built specifically for side feed fuel ports. For straight pull you can get a crow foot with a slide hammer that can grab at the same place the retaining fork in the engine slots into.
@WebstersWorkshop11 ай бұрын
Cheers will look for 1 next time I have a set to pull out. 👍🏻
@soggybawsmoto11 ай бұрын
Funnily enough, I’ve just bought a fourth motorcycle 😂. At least bikes don’t take up as much space. Good luck with the new project
@WebstersWorkshop11 ай бұрын
Thank you. These projects fo take up a little space but I'm lucky enough to almost have enough space to house them all 🤣🤣
@soggybawsmoto11 ай бұрын
Fantastic piece of diagnostics. Was great to see the dicky injector leaking off into the test tube. Earned my sub! It’s great seeing channels of a similar size to my own but in a parallel niche making engaging content. Hopefully we’ll both smash 1000 subs soon 👍
@80s90sVauxChris11 ай бұрын
Cheers for the shoutout although you didn't have to 😅 appreciate it though buddy 👍
@WebstersWorkshop11 ай бұрын
No worries. I did it because you did a video on the show and I didn't 🤣🤣
@80s90sVauxChris11 ай бұрын
@@WebstersWorkshop slacking 😂🤣 that's usually your department filming shows
@WebstersWorkshop11 ай бұрын
Not filmed a single show this year.
@barryjackson851211 ай бұрын
Fingers crossed you got to the bottom of it.
@TaylorStewart-mq5tu11 ай бұрын
Van looks great mate keep up the good work
@WebstersWorkshop11 ай бұрын
How bored are you at work today? 🤣🤣
@chris01028111 ай бұрын
I was hoping for another ep3 but I will be interesting to watch your progress on the van/camper
@barryjackson851211 ай бұрын
Look forward to seeing this progress 😎
@martinkirton9608 Жыл бұрын
Great as always :)
@WebstersWorkshop Жыл бұрын
Cheers.
@cliveberry3997 Жыл бұрын
Very smart 👍
@xplosm4197 Жыл бұрын
Helpful video, gotta tackle my rear hub as its groaning a little when turning. Do you know the torque values for the hub? and any tips to know on these?
@WebstersWorkshop Жыл бұрын
Can't remember what the torque setting were tbh. If you xan swing a spanner, you'll be fine with this. Was quite a straight forward job iirc.
@barryjackson8512 Жыл бұрын
Look canny
@WebstersWorkshop Жыл бұрын
Turned out well for a £100 ebay powdercoating kit. 😁😁
@callyman4x4 Жыл бұрын
Looks the Biz mate :)
@WebstersWorkshop Жыл бұрын
Inlet next. 😁😁
@rogerdickinson6944 Жыл бұрын
Good video!
@WebstersWorkshop Жыл бұрын
Thank you.
@spencerriddle2960 Жыл бұрын
Workshop looks good, looking forward to the wide arch Nova making progress
@WebstersWorkshop Жыл бұрын
Not as much as me 🤣🤣 just need to master this tig welding now and it's full steam ahead.
@braidenbrennan-fenton948 Жыл бұрын
where can i get these seats?
@WebstersWorkshop Жыл бұрын
I got these seats years ago from a friend for a different car, and I'm not even sure if they still make these. If you search "cobra clubman", you should find something very similar.
@able2pestcontrol530 Жыл бұрын
Canny mate 😊
@user-ub7qs2ju6n Жыл бұрын
Hi.Keep up with Calibra Jobs. I have w/brg to do soon this was great help.
@WebstersWorkshop Жыл бұрын
Pleased it helped. If your rear axles never been out you will need to drop the whole lot down to get the bolt out next to the sill.
@robson306 Жыл бұрын
Thanks for the shout out for north east zafira owners club page
@WebstersWorkshop Жыл бұрын
Not a problem.
@barryjackson8512 Жыл бұрын
My Biggest hate doing wheel bearings.
@WebstersWorkshop Жыл бұрын
Thats the reason I've been putting this off for a couple of years now.
@robson306 Жыл бұрын
Looks good just idea if you don't like them strips been white thought about putting some some light tint spray or wrap on them to tie in with the black 🤔
@WebstersWorkshop Жыл бұрын
I can get onboard with the white, it's the shape. I want them to curve a little.
@alexformallyofchintzmotorsport Жыл бұрын
Look forward to seeing you at vboa, I’ll be bringing the cav 👌🏽👌🏽👌🏽👌🏽👌🏽
@WebstersWorkshop Жыл бұрын
Pleased you're out and about in that again. Can't quite fir vboa like especially if the weather's like this.
@novasportregister8685 Жыл бұрын
Could you maybe use some tinting film over the LEDs?
@WebstersWorkshop Жыл бұрын
Get an mot on the car first then I can worry about it all at a later date.
@callyman4x4 Жыл бұрын
How about reversing the conduit and drilling holes that line up with the leds? Would be a solid strip look to it. Less lego appearance
@callyman4x4 Жыл бұрын
Do you have a link to the ebay seller Tony?
@WebstersWorkshop Жыл бұрын
Will post it up when I get 5. What with work and editing I've not stopped since 6 this morning. KZbin life 🤣🤣