Mend it Matey

Пікірлер

@davidthomas4670 11 күн бұрын

spot on

@kaiserhhaie841 25 күн бұрын

I know the original bolts are expensive at like 6 bucks a pop but i would rather spend 50 bucks on new bolts for the subframe than put some rusty shit on it, but thats just me. you do you, great work!

@marque_g 21 күн бұрын

Fully agree, also they are one time use, coz subframe to body bolts should be torqued 90Nm + 45 angle + 15 angle, lower arm bolts should be torqed with suspension fully loaded and they also have a torque sequence.

@stimac5003 Ай бұрын

What was the spark plug gap? 0.8 or 0.9mm?

@menditmatey3368 Ай бұрын

I read up that 0.8-1mm is an exceptable range. Not sure if that is correct or not. I didn’t check these plugs, the car ran fine with them.

@DEATHANGELCSGO Ай бұрын

How much litres of oil it requires

@menditmatey3368 Ай бұрын

4 litres, excluding the oil filter.

@dsedswe Ай бұрын

missed the torque specs for this also the carrier bolts are stretch bolts so can only be used once recipe for disaster like the other guy said

@chacals841 Ай бұрын

Thank you, with good tuto, you make a good job 😉🙃 For me, it's the left rear windows, but, it is surely the same to replace, thank , thank, thank you😉

@ccs9270 Ай бұрын

Have you to remove anything else besides the wheel to do this job ?

@ukreallifeL8 Ай бұрын

Is this the 1.4 engine ?

@menditmatey3368 Ай бұрын

Hi, it’s a 1.2 engine.

@austimbo 2 ай бұрын

Made the job easy. I have recently taken out both passenger side door locks. FOr the back one, you need to partially take out the window regulator to allown clearance for the lock to come out. FOr the front, n worries it slides right out!

@geoffaries 2 ай бұрын

Did you carry out any electrical tests before stripping down the door? Is it possible to determine if it's a motor problem before remving the door card. Thanks.

@menditmatey3368 2 ай бұрын

Hi, I didn’t do any electrical tests. I heard the cable snapping and making a grinding type noise when operating the switch. The front right window works intermittently on this car, I suspect it is the wiring loom that leads into the door that is at fault. I am hoping to do a video on this at some point in the near future. Thanks.

@geoffaries 2 ай бұрын

Many thanks for that. I can hear what seems to be the motor trying to work, so maybe it is the cable unravelling and jamming the gearing.

@mabsbry1318 2 ай бұрын

Brilliant video. Thank you.

@youarenotlikeme6224 2 ай бұрын

Thank u...i try on the weekend...good to know...thx

@bryancolquitt7008 3 ай бұрын

Disco 2 seat to do, sometimes your hands in the way so difficult to follow. Still it’s a Range Rover!😊

@joseluiscarranzarengifo9761 3 ай бұрын

Muy bien maestro.

@sivader17 5 ай бұрын

Enjoy the silence

@5karr 5 ай бұрын

Very well shot and explained and as such very helpful. Thank you for your effort and wish you all the best 🙂

@bruddab4474 5 ай бұрын

My window has fallen inside the door, the switch still works but obviously it doesn’t bring the glass up or down, it’s just always in the door. What should I do

@user-ly3ju6rj3u 6 ай бұрын

Thanks bro for the nice video

@user-io1nd8xp3l 6 ай бұрын

new screws !!!!!!!!!!!!!!!!!!

@snax31 27 күн бұрын

Your needing a new key board, your ! button is sticking on

@chrisgreenwood271 6 ай бұрын

Job well done, I'm lucky the heated seat on the drivers side still works on my P38, though I use it sparingly 😊

@shadinho100 7 ай бұрын

Thanks for the video. Which brand is that window regulator?

@menditmatey3368 7 ай бұрын

Hi, it was an aftermarket part I got from eBay. Thanks.

@emacapcoz6575 7 ай бұрын

Bonjour Est-il possible d'avoir le lien pour acheter le kit. Merci Emmanuel

@menditmatey3368 7 ай бұрын

Hi, this is the item I bought. www.ebay.co.uk/itm/272726693222?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=ghHntw65Q2O&sssrc=4429486&ssuid=x8qfUaibQrK&var=&widget_ver=artemis&media=COPY Thanks.

@Elwooddudes 8 ай бұрын

nicely done sir! i might renew my experts suspension soon. same colour as yours!

@alliurigels164 8 ай бұрын

Super

@lone_wolfe 8 ай бұрын

Quick question: I have to replace the alternator, but how do I know how much pressure I have to apply to the belt tensioner? i know thats most tensioner have some markers but i cant find any on this one

@menditmatey3368 8 ай бұрын

Hi, you want to get enough tension on the belt that will allow you to twist it slightly on the bottom. I done that in this video but it isn’t the best to see with the camera angle. Too slack and it’ll slip, too tight will cause premature wear or cause it to be noisy. Hope this helps and that you get it sorted. Thanks.

@tomrucroft9509 8 ай бұрын

Can you tell me what spark plugs you used. Thanks

@menditmatey3368 8 ай бұрын

Hi, I’m not exactly sure which ones, it may have been Bosch S07 plugs. Thanks.

@dazfrench 8 ай бұрын

Great video, very helpful

@MrCjlmr4 9 ай бұрын

Great video, recently did mine. Unfortunately im getting an annoying knock noise now. Been under the car again to check everything is tight but i cant figure it out

@menditmatey3368 9 ай бұрын

Hi, did you renew any of the suspension components? Double check that there’s no play on the anti roll bar drop links, track rod ends, and inner steering arms. Hope you find the issue. Thanks.

@MR_Charles04 9 ай бұрын

Thank you so much you made it so much easier🫡

@lorcannelson4220 9 ай бұрын

Hi, trying to manually pull my window up as i think the motor has gone, if i remove the motor unit should the window go up with little resistance? Thanks

@menditmatey3368 9 ай бұрын

Hi, If you remove the motor from the regulator it should allow you to pull the window up. Sometimes the wires in the rubber conduit going into the door from the car body can break and stop the window from working, worth checking. Thanks.

@footbol7733 10 ай бұрын

hallo ich habe gerne opel corsa.D aber ich muss immer motoröl.aufullen ich habe bei werksttat gekontrolliert.aber es gibt kein problem kein ahnung haben sie idee.oder eine hilfe ich müder immer motoröl.kaufen

@Doco72 10 ай бұрын

Nicely mended matey! Love the squeaky jack.

@on2wheelz28 10 ай бұрын

A master class!👌

@austinlinford5698 10 ай бұрын

Made the job easy to do. Thx

@kamelbenslim3129 11 ай бұрын

You are very professionel, thank you for your expliquation

@terence7752 11 ай бұрын

Save myself 50 quid with the help of this video cheers mate👍

@popo-pv7wl 11 ай бұрын

Why does he do the programing at the end of video? Is it necessary?

@paulsikora5623 11 ай бұрын

great A3 content ill now do my front A3 brakes N save some cash from going to a garage

@aloyys Жыл бұрын

Thanks you i did liké vidéo ans perfect

@harrybayley475 Жыл бұрын

Might sound a silly question how difficult was it to get the old bolts out from the old subframe

@menditmatey3368 Жыл бұрын

I used an impact wrench to get them off so it was fairly easy.

@jamesbremner9957 Жыл бұрын

Nice work. Quick question, did you note where all of the bolts go? I may have been a biff and stripped the subframe off without noting where all of the bolts go. I've now realised that most are different sizes!

@menditmatey3368 Жыл бұрын

When I was removing the old subframe I set the bolts aside and then screwed them back into where they came out, once it was off. Hopefully you get it sorted. Thanks.

@jamesbremner9957 Жыл бұрын

@@menditmatey3368 Cheers mate. I wasn't that well organised so will blow most of today with trial and error 😂

@menditmatey3368 Жыл бұрын

@@jamesbremner9957 you could try matching them up with the old subframe, to see how they look. I’m not sure from memory if those bolts are different lengths. I think the 4 steering rack bolts are notably different from the subframe bolts.

@user-nm5gi2we4j Жыл бұрын

Really appreciate this format. No irritating background music is so appreciated. After being a bit freaked by the Hayes narrative am now cracking on with a lot more confidence. Getting the old bolts out is another story, needs time and patience to avoid rounding off bolts and destroying captive nuts. Advise any novices like me to study the many utubes on this topic. Great work on putting this together and sharing.

@chispaflores871 Жыл бұрын

Jolín cambiaré mi elevalunas gracias a tu vídeo muchas gracia

@Doco72 Жыл бұрын

Nicely mended matey. Liking the camera work, ken?

@dustandcobwebs Жыл бұрын

thanks for this video. I needed to replace my tie rod ends and this helped me get it done super quick. Absolute legend

@shaykh_Mahboob Жыл бұрын

Did you cut the zip tie at 22:05? I did mine much earlier and messed up the regulator. After fiddling about with it, i fit it on and heard a crunching noise and the metal wire came off. Now I have to purchase a new one.

@menditmatey3368 Жыл бұрын

Yes, I cut it at that point.

@geoffaries 2 ай бұрын

Well spotted!

@davidbates247 Жыл бұрын

How much do you think a garage would charge for labour on this thanks good video

@menditmatey3368 Жыл бұрын

It shouldn’t be any more than 2-3 hours labour for a garage. Not sure what the average going hourly rate is these days.

@sobo5476 11 ай бұрын

Bit late here, but about £500, if you want to use Vauxhall official parts add another £300 to £500 on.

@wmsstuff271 3 ай бұрын

@@sobo5476 Aye. I just paid 780 quid for new subframe and control arms fitted. Sore, but this job is beyond my skills.

@peterwarner8541 Жыл бұрын

Thanks very much for this. I’ve just done my passenger seat today. Hog rings were a pain. The backing of the leather was all disintegrating too so was constantly showered in black dust, nightmare sticky job!

@rudo747 Жыл бұрын

Pays to clean your air mass sensor with electrical connection cleaner spray while you are on and depending on your mileage £20 gets you a new purge valve which is worth changing while you are on as they are a common problem on these cars👍

@user-dj7ex7oi5r Жыл бұрын

Спасибо

Ең жақсы KZbin

Пікірлер