U pmo dislike

Im having the same issue, except I can only get one to tighten…

@tahneemichelle7819 wow really? I thought it was just us

Two guys recommended, I'd say the job takes about an hour or less with two people. If you have good paint and you're doing this yourself, just take your time and make sure the paint is protected.

@FirstTimersChannel That's what I thought. I was in the Hospital in a coma & most of my tools were stolen! They took my keys,made copies & began to rob us one sock ,fork & small pieces at a time. You don't know something is missing until you need it. Turns out they put cheap hidden cameras in my house so they knew our every move. A lot to deal with while battling stage 4 spinal/Renal cancer! I'm going to be at everything! Thanks for the help & GOD BLESS 🙏!

@CZECHMATE650 Wow, that sounds terrible! Good luck and hope for a speedy recovery! 🙏

@FirstTimersChannel Do you know if it's possible to torque the caliper bolts with the wheel on??? (On the ground) . It's REALLY difficult to get up and down now. Thank Goodness I'm as tough as a $2 steak!

@CZECHMATE650 While the car is on the ground, I would say it's not possible. You would have to get behind the wheel with a torque wrench and use an extension since the wheel is on. It's just much easier to jack the car up, put the car on a jack stand, and remove the wheel. I recommend doing things right or taking the job to a shop or professional. Brakes are important.

That's why we are the First Timers 🤣

Thanks for commenting! Glad this video helped!

Nice! Thanks for commenting and sharing your experience with the parts!

This stereo made the sound quality way better! The volume was the same, but I also didn't have the JBL system, so I can't speak for that.

Whattup!! Congrats! Keep it up! 🤘👍👏👏

In San Fernando Valley California

They're holding up perfectly so far, with no complaints at all!

No, I guess not. It just does this for the plate. Know of a way to do the same for the tail light?

@@keithmatthews7868 Hi there and thank you for your question! This was a license plate tail tidy custom made by a Hawk forum member. This one came from one of his last batches that I was begging him to make. I would imagine, if you can get a custom tail light, you can get it to mount somewhere on one of these if you have one. Otherwise, it's main design purpose is to remove the stock rear fender and make it a cleaner look for the license plate and turn signals.

Do you think those hinges Can be Repair instead of buying them?

Hello and thank you for your question! We bought the hinges off of Amazon at about $50 each. Got the OEM part. The links are in the description of this video. Unfortunately, don't think they can be repaired as it would be hard to align them properly. It would be easier to just replace. Hope this helps!

@ thank you very much for answering me. I appreciate it

Same here.

Sorry for the late response. Yellow is battery power and red is Acc. power.

@FirstTimersChannel thank you

Thank you and thanks for commenting!

We don't know for sure, but I think it's safe to say that no, they are not the same.

Thanks, hope you are doing well.

Im assuming you are referring to the door panel on the inside. That silver part pops off so you can access the screws behind it in order to remove the door panel.

@@FirstTimersChannel yup that part, but wondering if the handle (that the silver panel attaches to) can be separated out from the whole door panel. the leather on mine is coming off and wanted to know if I can take that apart to rewrap the leather

@ChiHoKo I don't think so. It might be all molded into the whole panel, but I can't say for sure.

Yup you are correct! But in our case, the ground at the stereo plug end was good enough. Thanks for commenting!

Apologies for the delayed response. Based on what I know, it should work just fine. However, if you'd like, you can check out this alternative-it's labeled with both "GoPro" and "Osmo" in the title. amzn.to/4g8NRU5

@@FirstTimersChannel No stress about the delay. Seemed to work well!

Dealerships don't want to waste time cutting each bushing out so I can understand that they would rather just change out the entire subframe. It took me a VERY long time to do this. Any shop would lose money if they changed each bushing out.

Apologies for the delayed response. It can definitely be done, but I would recommend removing the glass if you're doing all the work yourself. Leaving the glass in would essentially turn the job into a large patch job. You’d need to cut the metal around the windshield and rear glass to use those areas as attachment points. The tricky part is ensuring the roof maintains its proper shape after cutting and reshaping the metal to match the new area. Keeping the shape while welding is also very tricky and will take a lot of time. Again, recommendation would be to remove the glass and do the full replacement.

You're welcome! Glad this video helped you save $$

Hey, no worries and thanks for coming back! Glad it did help!

I'm going to have to do it myself. How long did it take you to do both sides? I'd like to have any pointers you can give me!?? PLEASE??

@CZECHMATE650 The hardest part, I would say, is holding the hood up while lining up the brackets. Since you are doing this yourself, maybe put the hood on a towel on the opposite end to lift and protect the corner from damage as you try to mount one side. Don't fully tighten the bolts on the hood so that once you have both sides bolted down, you can line them up, then tighten down. That's all I can really think of. Good luck, and thanks for commenting!

2014

Not a big difference with stock jetting and the TBR. There was a significant difference after re-jetting to stage 3 with pods and the TBR. Unfortunately, we didn't do the changes one at a time. It was TBR exh first, then we did the jets and pods at the same time.

@@FirstTimersChannel Thank you for your reply. Does the stage 3 upgrade consist of exhaust, pods and replace main and idle jets in carbs?

@@swordfish1120 Sure thing! The stage 3 jet kit consisted of just the jetting in the carbs. To utilize the full benefits of this mod, it's best to add the intake air pods and an exhaust. There are different jetting for the setup you wish to achieve.