Zhivago Blea

Пікірлер

@benonchuk1 16 күн бұрын

Straight to business, no mucking about .thanks

@Greg_janny 2 ай бұрын

Fuck yea bro lmao

@joem7062 4 ай бұрын

When i do this i tack the trim pieces to a wooden work bench with pin nails. I screw scrap wood blocks to the bench then nail the trim to the blocks with 18 ga pin nails. Just two. Then route continuously then you can pop the piece off the pin nails with one tap of the hammer. Or use a router table.

@elmerfudd835 7 ай бұрын

Is that 1/4 or 5/32 bit?

@vasileseitan6893 Жыл бұрын

if you don't mind, how wide is it, thanks

@preonmodel9906 Жыл бұрын

Screwing it to the workhorse from underneath means you could do it in one pass .. that would save some time.. but hey, who’s rushing! Thanks for the video as I’m giving this a go soon

@andrizeefoshizee 2 жыл бұрын

Man, that's cool! Nice "tada" afterwards. Made me chuckle

@xmj225jg5 2 жыл бұрын

just got a 2hp router to make our baseboards. This vid helped .

@iliketakingshowers 2 жыл бұрын

No way. Are you doing this on common boards? Looks like it

@Spain42 2 жыл бұрын

As simple as this was.. this is by far the best video I’ve seen for setting my router bit. Thank you for the side view and getting to the point. Some people tend to talk too much.

@egorbiletskiy2950 3 жыл бұрын

Woodprix Blueprints has some very useful blueprints with all the details you need.

@jbstepchild 3 жыл бұрын

Just wanted to say if u clamp it from the backside haha I said backside but then you can run a clean pass no stopping

@jend4128 3 жыл бұрын

Looks Great!

@javierortega6217 4 жыл бұрын

What size Roman ogee did you use?

@JACKNCOKE223 4 жыл бұрын

Great job! I'm new to routing, but using this video for trim will pay for the router on the first job alone! Thanks!

@brettking8663 3 жыл бұрын

Same here

@hannahmendoza4731 4 жыл бұрын

Omg got a little tearful when I seen this RIP Rudy

@erniebornheimer 4 жыл бұрын

Viva Zhivago!

@louishollandjr 4 жыл бұрын

Why not clamp it from behind your cut one with two Passes.

@Zhivagoblea 4 жыл бұрын

Louis Barksdale it’s a narrow board. Where ever it’s clamped it’ll bump. So I thought it more accessible from the front.

@tip397 4 жыл бұрын

Hi, can you tell me the exact size of the ogee bit please? Thanks.

@Zhivagoblea 4 жыл бұрын

tip397 it’s a Freud 99-484. Hope that helps.

@Christopher-lk4zd 4 жыл бұрын

I hate Tulare county

@huasmiguel9950 4 жыл бұрын

what why thoo

@KingCheckOut 4 жыл бұрын

We’re better than our north and south counties Fresno has drug deals happening everywhere meanwhile Bakersfield has homeless everywhere And Visalia has fights everywhere lmao

@23fields 5 жыл бұрын

Some people say clamp the other side of the wood....I say clamp the router and set up a fence if you had a bunch of them to make.

@joereyes7723 5 жыл бұрын

Whats Up my visaliano potnas Big love from young Cholo boy de NSVB

@knikkole6501 5 жыл бұрын

Yyeee

@darkmurcielago 5 жыл бұрын

Can anyone tell me if there’s a setting on the router because idk how he’s doing a straight line like that ? Lol usually the router keeps going deeper right ?

@Zhivagoblea 5 жыл бұрын

Obe, I put it at the height I needed and what stops it is the bearing at the base of the router bit. Make sure there is one.

@darkmurcielago 5 жыл бұрын

@@Zhivagoblea Thank you so much!

@mcarr4903 4 жыл бұрын

There is a bearing on the router to stop it going deeper

@volcanowb 5 жыл бұрын

Nice

@Lsi581 5 жыл бұрын

You should clamp the other side of the board so you can do one straight run

@richardprocter4622 2 жыл бұрын

I concur

@TheBmontalto 5 жыл бұрын

When I tried to create a profile on the edge of a 3m long board, my routing lines never match up. I'm at wits end about this. Probably I'm not accurate enough doing freehand routes. I'm guessing a router table would help tremendously..?

@90210sky 2 жыл бұрын

this is not free handing , there is a guiding bearing in the cutting bit.

@bobabooey8367 5 жыл бұрын

The neighbors would appreciate a basement shop

@Zhivagoblea 5 жыл бұрын

Nice! See how the neighbor parks at 28 and at 50 seconds you can hear another power tool in the distance. A lot of DIYers! It's the tweaker neighbor fiddling around at midnight that gets the dogs going that's the problem!

@bobabooey8367 5 жыл бұрын

I hear Ya:)

@meme5607 5 жыл бұрын

The kkk ratchet 2

@sahibbansal5912 6 жыл бұрын

*This is my new favorite trim router...... and I use a lot of routers.>>>**do7.info/088o** Smooth, quiet, and nice feel. I also prefer round base trimmers*