Thank you for all of your videos. Please make more again.
@randyharrison46717 күн бұрын
I let someone ride my bike and they over reved it until it I think blew a head gasket,I think. What could have happened it was out of antifreeze when I looked at it but I had topped it off the weekend before so I didn't check it, the oil was milky so I figured a head gasket or something?
@Sherman18629 күн бұрын
Am I supposed to insert both sides of tire bead between rim lock and bead? I just put tire on and let tube rest on top of rim lock. I inflated tube after, tire install and the bead is about 1 centimeter bulged out on the sides of rim.. Not sure that's correct.. Lol. I think I F* up.. That tire was a pain to put on too!!! Rear 16 inch E ride Pro E Moto Warped 9 custom wheel. .. Hope I don't need to do it over? Any thoughts greatly appreciated. Thank you! Great Video!
@Fixyourdirtbike9 күн бұрын
Yes, both beads. It sounds like your rimlock is offset, causing the bulge. Deflate the tube and push your rimlock in and out until the threads are straight up and down.
@Sherman18629 күн бұрын
@@Fixyourdirtbike Thank you! I'll try that!
@WillAllen-c8l19 күн бұрын
Was that on a crf150f
@zacharydewitte38422 күн бұрын
Tip you wouldn’t be replacing them if you bought one I bet all ball seem terrible from my experience go Honda oem all day from Japan not tawain
@Fixyourdirtbike22 күн бұрын
Japanese OEM for the win
@zacharydewitte38422 күн бұрын
@@Fixyourdirtbikeyou only save like $15 getting all balls
@ericgrajeda267125 күн бұрын
Will the paste work with gas on the tank leaking....
@Fixyourdirtbike25 күн бұрын
No, the surface needs to be cleaned and dry.
@iitsbryzze873826 күн бұрын
How important is the seal washer? I don’t have it and I’m not from the US so I don’t want to import it and wait for like a month for it to arrive 🥲
@ModModRc29 күн бұрын
How do i get the right size rim lock? Vernia Caliper say, rim width 2.15" Rim has 1.60×19" stamped on it. What rim lock do i need, a 1.6 or 2.15?
@jamesclarke1754Ай бұрын
Ok but where do you set the fuel idle screw at to start?
@Be_A_GoonАй бұрын
My idle is fine until it gets hot and I put it into gear then it dies
@FixyourdirtbikeАй бұрын
When your engine warms up, the air warms up with it, making the air less dense, which drops the oxygen level of the air. It sounds like your mix is too rich when warm. Can you cheat it with throttle?
@tbounds4812Ай бұрын
i feel stupid for not understanding it but man this video was exactly what i needed for understanding how a rim lock works thank you (:
@FixyourdirtbikeАй бұрын
Glad to help!
@TreDogOfficialАй бұрын
I hit a rock and i can't seem to hand file the groove back. Is the electric sharpener more efficient?
@gumundurandresson3919Ай бұрын
how is the upper screw to be not air i think the throttle screw? black with a sping on it? thanks G
@FixyourdirtbikeАй бұрын
That could be the throttle stop, but it depends on what carb you have.
@JaxonJonart-og6myАй бұрын
Can you show us a video on how to put a new dirt bike tire on to pump up the tube
@nicksadler2785Ай бұрын
I have a 94 yz125 that I brought in pulled apart... I can't find the ground wire, it's not on the CDI, magnetto, or wire loom, does the 94 not have one?
@CooperMunn222 ай бұрын
My distance collar had a slight bur and I grinder like half a miler meter off to make it smoother is that ok?
@kasperebbers64522 ай бұрын
Always measure stator coils without flywheel!!!! The flywheel effects the measurements of the source coil 1
@adammanderson19952 ай бұрын
Can they leak if u dont bleed if the bike has being moved in a car just a question have a pitbike with one leaking and the other ok only started happening after i picked the bike up after a week i have rode the bike yet so im assuming there ok just need bleeding and the seal mate putting in the em its a kxf125 pitbike not sure on the fork oil weight what would he recommended for a pit bike
@thisbedoogy2 ай бұрын
good video bud, but like others have said, don't hold the grinder like that, it will go right in your forearm
@trmotry2 ай бұрын
Where can i buy the main jet mount? I cant find it anywhere
@Fixyourdirtbike2 ай бұрын
You can't, unfortunately, without buying another carb.
@SteeleNeville2 ай бұрын
Do you know anything about racing carburettors I have a racing carburettor on one is it any different
@zackk6952 ай бұрын
I see you wiped off the reeds very quickly. What do I spray them with to clean them? Is carb cleaner ok?
@Fixyourdirtbike2 ай бұрын
Yes, carb cleaner is ok to use.
@Deathlobster1372 ай бұрын
Yo dude, I tried to assemble the shift assembly and it was jammed up. Everything appeared to be normal, what should I look out for? I have it all apart again.
@Fixyourdirtbike2 ай бұрын
The pawls in your shift drum may be bound up.
@travisstickells73612 ай бұрын
Website finally went down - thanks for all the help!
@Fixyourdirtbike2 ай бұрын
Ha! It got hacked, I'm working on it now, actually.
@travisstickells73612 ай бұрын
@@Fixyourdirtbike damn bro I didnt think you still even monitored these videos! I have used your site and videos to completely rebuild my 97 CR250. Invaluable information and breakdowns. Just picked up a 2004 YZ250F that needs a rebuild and its like I am back at square 1 again
@travisstickells73612 ай бұрын
@@Fixyourdirtbike My 97 CR250 starts fine and idles but after actually riding for about 5 minutes, it dies. It SOUNDS like the piston is seizing and the kickstart actually locks up, but if I rock the bike back and forth a little it will get unstuck and after waiting a while I can start it again. Any suggestions on what to even look for? Could the piston actually be seizing and then cooling and unseizing very quickly? Crank issue maybe? Just put new crank bearings too.
@Fixyourdirtbike2 ай бұрын
Glad I could help!
@Fixyourdirtbike2 ай бұрын
That's... wierd. The rocking thing is interesting. Did you gap your rings during installation? The piston is unlikely to expand and contract that fast and that much unless it's a bad casting. Did you set the crank seal depth?
@derekkenney83952 ай бұрын
What size socket do I need to take off clutch after I flatten washer?
@3dwezzy7402 ай бұрын
🎉
@_Deadlystrain_2 ай бұрын
can you use a TMX38 carb for a 2000 yz125 even though its suppose to be a TMX36?
@og7hc5343 ай бұрын
Question what would happen if the gasket for the jet block gose bad will it make the bike flood out ??
@Fixyourdirtbike2 ай бұрын
Yes
@billterri48893 ай бұрын
Did you remove the seperator cup before cleaning the master cylinder? The manual says remove, inspect and and repolace the o ring underneath iof necessary but it doesn't show how to remove it.
@righton1293 ай бұрын
How dis you remove the bolt what did you use?
@BraxtonPlanck3 ай бұрын
I just got my dirtbike and I ordered pro taper, grits diamond hopefully that works because my last grips whore the skin off my hand
@TheClimberbob113 күн бұрын
Do you not wear gloves?
@robertrishel36853 ай бұрын
I used this stuff back in the 80’s, smells soooo good and used to keep my 125’s alive👍
@mimaygarcia13383 ай бұрын
Thank you for this video bro,,i applied it and it works ❤❤❤ i thought my master cylinder is broken almost 2 days doin it and it doesn't work 😅
@Peyton_Edwards3 ай бұрын
Keep the opposing nut side pinch bolts tight so when you unloosening the nut it holds it
@2stepYo3 ай бұрын
thx
@2stroke_pawlos3 ай бұрын
I have a problem when I pull the throtle fast its chokes Its not comfortable when I riding enduro pls help
@swapnifty84863 ай бұрын
what kind of grease are you packing the seals with?
@andreasgunnarsson72763 ай бұрын
Where to buy this in EU?
@Eteen123 ай бұрын
lol thanks. Finally dialed in my KDX
@ozbulitsinces19964 ай бұрын
How do you re set the idle adjustment knob ? My cr want ideal IV had the bike for year and never had a proper IV clean carby and new plug and still want ideal. I did take the idle screw with the lock nut out when I was cleaning it and forgot how many turns can you please tell me how many ruffly in it should be
@davidh13144 ай бұрын
Well done video. thank you
@nardo24v4 ай бұрын
awesome video
@OrofinoSeb4 ай бұрын
Very effective! Please keep going making cool videos
@ozbulitsinces19964 ай бұрын
Hey John what the stock setting for the suspension
@D_rock447114 ай бұрын
Thankfully, my wheelbearings aren’t shot onto another video Why is my brake caliber sticking?
@ildefonsomarin60054 ай бұрын
I'd assume this is the same thing or close enough for minibikes. Hopefully this helps me out🔥🤙
@Workerbee-zy5nx4 ай бұрын
1.5 to 2.5 turns out from fully seated.
@mason_childs33354 ай бұрын
This video sucks need to slow down
@Fixyourdirtbike4 ай бұрын
Watch it twice
@basementracer4 ай бұрын
I highly recommend two RIM locks. I use Nitro Mousse Platinum and I had my rear tire come off the rim last Sunday on an FE350. We were getting after it over some really gnarly rocky stuff and I guess she just rolled off on a rock. I made it back because the mousse held together and the single beadlock gripped the tire to allow traction. I have just ordered more rim locks need her ready for this weekend ride.