Really? An evo engine? Better uses for that engine than drag racing
@nexxracing2 ай бұрын
Lmao. What other uses are there? Drift, Road Race, Street Car? All good uses for a motor that can handle abuse!!
@Phillipkleinhans3 ай бұрын
I Really appreciate the Cleanliness, indicates quality workmanship, i really wish more youtubers would show us the same. Thanx for an excellent Video.
@EasyGrowDude4 ай бұрын
I need a gasket for 2g gst ASAP how do i get one
@angaleimotu4 ай бұрын
Thank you sir
@sammyturbo7865 ай бұрын
Is this a kit you bought or are you bending everything to fit. Where did you get the ford 9 and 4 link setup? So so good looking good keep up the good work. I would love to build one similar to yours.
@nexxracing4 ай бұрын
I took the measurements and had a place cut and bend the tubes for me. I still had to notch each tube to fit. Almost everything on the build is from Applied Racing Technology in St. Pete Florida. Thanks man fabrication portion is almost done.
@66garagecilacap6 ай бұрын
Does these coils work on a stock ecu?
@nexxracing6 ай бұрын
Yes but requires special wiring. You can get the special wiring adapter at ohm-racing.com . It’s called OHM Racing Plug & Play IGN-1A “Smart” Coil Ignition system. The price is pretty expensive though.
@66garagecilacap6 ай бұрын
@@nexxracing thanx for the info 👍
@redeclipzegsx6 ай бұрын
Are these still available? I need one for a 7 bolt. Where can I purchase?
@nexxracing6 ай бұрын
Find us on facebook at Nexx Racing!
@octavianhathorn15757 ай бұрын
Looking very good. I got a rwd 4g build I'm almost done with. Full drag car.
@nexxracing7 ай бұрын
Love to see your build !!
@edrontromp29667 ай бұрын
Sick build
@mcezlla81927 ай бұрын
Super clean, found your channel from this short. Can’t wait to see how it turns out! This is going to blow you up! This car is sick!
@suzpekted7 ай бұрын
You need an engine block earth to power them 🤦 head is just to fire them
@nexxracing7 ай бұрын
You just need to attach it to your star grounding point. 1 ground wire goes to Ecu reference Ground and the rest to your star grounding point on the head or block
@SpeedGasmEvo98 ай бұрын
How do you unfill it?
@SpeedGasmEvo98 ай бұрын
How long can you run a full fill block for?
@nexxracing6 ай бұрын
Depends on some factors but id say its not something you’d want to run for more then 30min at a time. In terms of longevity of the block just depends how hard you run the block and the upkeep .
@dinorodriguez52319 ай бұрын
Oem gaskets suck I’ve gone through 2 and leak even added a bead of good oil resistant silicone gasket and still leaks. I want to try your gasket.
@dinorodriguez52319 ай бұрын
Do i need to bead it with gasket silicone ?
@nexxracing4 ай бұрын
No not required
@russellharris95799 ай бұрын
What is the service life of your blocks after this treatment?🇦🇺🦘👍
@nexxracing9 ай бұрын
I mean it doesn’t change the service life, you obviously can’t run coolant through the block so the block can only be used for drag racing. Just depends on how hard you’re running the motor.
@nyvinchenz943010 ай бұрын
Ok so your sad about atco dragway so what type of biuld you planning on that evo motor
@nexxracing9 ай бұрын
All out beast !!! Billet crank, aluminum rods, anodized cp pistons , comp plus valves and s3 cams , dry sump system, it’ll be a 1000hp+ beast
@nyvinchenz943010 ай бұрын
Where you get that set up from
@nexxracing9 ай бұрын
Applied Racing Technology in St Pete ,FL
@nyvinchenz94309 ай бұрын
@@nexxracing thank you
@randybishop162110 ай бұрын
just trying to figure out my Rx-8 project don't really know which way to go yet? would appreciate any information on your frame rails, who did you order them from? Looking Fantastic!!!
@nexxracing9 ай бұрын
They’re just universal frame rails you can get from any chassis shop. I’d recommend going with the tubed version though , going to be lighter and just overall better.
@yammy276910 ай бұрын
How to wires with 3sge beam
@joseantoniodaly487511 ай бұрын
Is it a problem if I use this filler AFTER block bored?
@nexxracing11 ай бұрын
So for this filler they manufacturer states it can be done after block is bored. I would definitely recommend checking piston to wall clearance after you fill it to make sure nothing has changed!
@BoostyGeoff Жыл бұрын
Bro im from the uk and i just wanna say your build and workmanship is so inspiring, giving me motivation to get on with my drag rx8 build! Keep up the awesome work!
@nexxracing Жыл бұрын
Thanks, comments like these are what keep me motivated. Thanks for watching! Hope your subscribed!
@anthonyjohnes6816 Жыл бұрын
TEAM Los Rompe cuellos 🇵🇷💪💪
@nexxracing Жыл бұрын
Vamo Alla 🇵🇷
@Murphyslawfarm Жыл бұрын
G'day great work mate. Glad to see you growing subscribers mate.
@nexxracing Жыл бұрын
Thanks hopefully we can get a lot more!
@JoseSantos-n2l Жыл бұрын
Primo. Keep up the good work 👍
@nexxracing Жыл бұрын
Thank you, I will
@Murphyslawfarm Жыл бұрын
G'day great video
@Murphyslawfarm Жыл бұрын
G'day great update video mate
@Murphyslawfarm Жыл бұрын
G'day great progression mate
@Murphyslawfarm Жыл бұрын
G'day from nsw Australia just found your channel and subbed mate
@nexxracing Жыл бұрын
Thanks for subbing
@TTGTO288 Жыл бұрын
Guys like this make me laugh. Probably takes the block to the machine shop and says "deck it" with no measurement to deck it to. Guys like this make my engine builds look great, like top fuel dragster engines.
@nexxracing Жыл бұрын
These blocks still have to get bored, honed , line honed, decked , make sure the piston to wall clearance is to spec for the HP im going to run. Not sure where you get that I’m just going to deck it. I’m not one of “those guys”. Appreciate the negativity though!
@HandMadeWrath9 ай бұрын
@@nexxracingtellm!
@Maty1t Жыл бұрын
Hey I'm interested in the gasket you make for the 4b11. What are the recommended torque specs?
@djgravit-e3193 Жыл бұрын
Are you still making these? Can you post a link as I can’t find you on Facebook!
@nexxracing Жыл бұрын
Search up Nexx Racing on facebook facebook.com/NexxRacing
@wilfredgrady Жыл бұрын
Promo sm
@Bajanplaidman Жыл бұрын
Where did you get the plate they are bolted to?
@nexxracing Жыл бұрын
JmFabrications.com
@haydnpaull5447 Жыл бұрын
A creeper stool could have made the task much simpler.
@carlosceoofredlinequickshift Жыл бұрын
Wanted one for ages nice build
@carlosdavid1828 Жыл бұрын
👏🏽👏🏽👏🏽
@08lerash Жыл бұрын
Nice work
@jay20747 Жыл бұрын
rx8
@daniel2064 Жыл бұрын
Can you fill a block after it has been machined (bore and honed,, mains aligned)?? If you fill a block 100 percent can you just flow water through the head...for light street driving.
@nexxracing Жыл бұрын
HardBlok says you can fill a motor even after it’s been machined. I just prefer to have it done before it’s machined. Now that’s hardblok , the moroso engine filler you have to do it before the block is machined cause it changes the blocks shape a little. Now I do plan on running water through the head , but my motor is for drag use. I wouldn’t recommend a full fill for street use unless ur running methanol which lets the motor run at cooler temps. Just my opinion tho!
@youwantshum9860 Жыл бұрын
You can't drive a fully closed deck on the street, maybe for a few minutes
@TTGTO288 Жыл бұрын
No, fill it before.
@HandMadeWrath9 ай бұрын
@@youwantshum9860thats unfortunate
@remybrouwer87002 жыл бұрын
No baffles ?
@nexxracing2 жыл бұрын
Nope don’t need it the way it’s built , pan is built for drag racing, straight line not side to side for street.
@FWBWpucas2 жыл бұрын
Hey buddy what size an fitting are u welding on head ?
@nexxracing Жыл бұрын
-16an
@prosportauto49222 жыл бұрын
@Nexx racing - you wont be able to change the oil filter housing unit with another one - as that means you wont have an oil pressure regulator (which you need for the FF pump).
@nexxracing2 жыл бұрын
Peterson sells an oil filter housing and oil pressure regulator that I can put together that’ll work with the frontline fab oil pump . No worries I got it all figured out.
@isaiahdanielvlog2 жыл бұрын
does the oem one just suck or what? havent put it on yet but I can tell its baaad underneath there
@nexxracing2 жыл бұрын
Doesn’t really come with one oem , you just use a shit ton of rtv which is a hassle to mess with! Or get one of the cheap ones from the auto parts store that you’d still have to add rtv to cause if not it’ll leak.
@isaiahdanielvlog2 жыл бұрын
@@nexxracing Yea i was checking yours out because a while back im pretty sure bought an oem one because underneath my car its gooey and leaking from the pan. It seems like its common with the original gasket or something
@rype362 жыл бұрын
Lemme know how that water air intercooler setup works out for I've been debating about doing one
@UzumakiGarage2 жыл бұрын
You need to put the bung in the other way around. The machined down side goes into your exhaust pipe.
@khemrajhsamaroo36712 жыл бұрын
Hey bro, how long did it take to get that oil pump from them ?
@nexxracing2 жыл бұрын
About 8 months
@ReviveAndDrive-mk12 жыл бұрын
So Good result with this gasket 😁?
@nexxracing2 жыл бұрын
Haven’t had Any issues,
@ReviveAndDrive-mk12 жыл бұрын
This wud be nice i am tired of rtv gasket lol 😁 and mine is leaking abit lol
@nexxracing2 жыл бұрын
Hit me up on Facebook, I’m currently making a new batch of gaskets