Тапорная работа!

What is the name of this tablet?

thank you soo much bro i nearly want to throw my pendrive wkwkwkwk

Доброго вечора, а можеш на малювати схему підключення такої ж плати, не можу ні де знайти, буду вдячний

Wer schneidet bitte mit ner Kombizange Kabel ? Und ich bin kein Elektriker 😂

Was soll man dazu sagen außer: "Ein Meister bist nicht gerade!"^^

Vorher schauen ob Dampf drauf ist. 1. Dass es kein Elektriker ist und 2. Man nimmt keine Kombizange zum kabelschneiden....

Wer kennt es nicht,hast du die Sicherung raus genommen,ja der Meyer hat geguckt,und Müller hat gesagt die ist draußen,willste auch nen Kaffee,klar bis gleich,und Zack wird's dunkel 😅

Erster Tag mit der Neuen Zange die du gerade erst bekommen hast.....

Erster und letzter

Naja denke nicht das ein Elektriker mit ner Kombizange Kabel schneidet

Was ist dass für eine stumpfsinnige Aussage? Erster tag als Elektriker ? Als Lehrling oder als fertig ausgelernter Elektriker. Wenn du ausgelernt bist, müsste man dir den Facharbeiter sofort wieder aberkennen.

Alles richtig gemacht

i think there was something about that you have to do download and do something to the music before it can be plaued over a tesla coil

Great job, but where from I get replacement parts I am an old man not an electrician or electronics guy 😀

کارت خوبه دستت دردنکند ولی تو تصویر مشخص نیست که سیم هارابه کجا لحیم کاری میکنی؟

You fixed it. But, could you please explain what was really wrong with the toaster? There was nothing we could detect wrong from the experiment you carried out.

I assume this was simply a straight replacement of existing li-ion batteries, and all BMS, discharge protection, and charging facilities are already on that circuit board? If not, then you’ve got a one shot lamp until those batteries run down below their viable recharge level, and then some desoldering and careful manual trickle charge nurturing to do, to get the batteries back up to their nominal 3.7 (max 4.2) volts again…

on 10:10, what's this wire thing?

Das ding läuft 30 jahren und mehr, kostet auch 25€, warum soll ich es reparieren 🤦🏼

Hi where did you get the charger from

আপনার কাছে থাকলে। বলবেন আমি নিতে চাই।

ماذا تفعل عزيزي ليس بهذه الطريقة يتم التعامل مع بطارية الوثيوم ولوحة البطارية تحتاج لجهاز فك الحام وليس كما تقوم بشد البطارية

Bisu

On the 1KZTE built in 2005 the pinout for self diagnosis is 4 and 13.

Not very informative

Hallo ,ich hab die gleiche leider drei eine reife Leuft langsam dann nach par Sekunden geht aus

Te lo compro

Hmm, what happened with the steel 'half'ring in the front ? As I can see you didn't replace it again.

I get it into start

Nice, but the problem is how to find spare parts. It is almost impossible in some areas. And if you find any part with no numbers on it you will have to buy a new PSU.

Cool battery fix. that sound is the roller brush. The bearing cup opposite of the drive end is worn. Hot glue fixes that right away.

Hi denis, hier ist Max aus der Schule, hast du Instagram?

Same issue, wire snapped off the coil at the connector. Ended up positioning it near the connector and then dumping hot solder in the gap to bridge it. Works again. Thanks for posting!

😅 Promo-SM

That is exactly how I got my 3000 working again.

Goedemorgen ik heb een toyota opa en start niet. 2 keer nr de monteur gebracht alleen uitgeven,juist erger geworden. Eerder door te lang rijden gt de motor dan uit, dus kan nt vere afstanden mt de auto. Naar de monteur gebracht kan nu nieteens meer starten. Nieuwe sparpluk, battery, beld etc.😢

My Siemens device gives the message "Door is open", when it is not and no door is open. Also, by turning the device off and on, the message remains and the device has no function. What do you think this sign is? Thanks

What is the name of this replacement part ? Is that pump part?

great job you make this stuff look so easy!

How long did it last

Ahhhhh ohhhh hahahahahweeeee-ohshit

Can it detect gold

hello i have the some problem to... but that solution is not working..... what can i do？

Halfway done with mine. Just now found this video. I wish I would have found it sooner. I hope I don’t find that I screwed something up. I’ve been just reading the screen printing on the board and using a multi meter to read the components and I’ve been hoping I’ve been putting them in the correct spots. This video should make things much more clear and a lot easier. Thanks for posting

Please short the Electrolytic capacitor thy bite

Where to buy battery for this same unit?

7 batteries why put 6?

Thank you so much for this tutorial, I can repair my phone with success !

Useless...