At 7:36 it is mentioned that the primer should get sanded down to 600 grit OR sealed, does that mean if your using sealer, you do not need to sand down the primer to 600 grit but if your skipping the sealer, you do need to sand down to 600? But on the car, it showed you sanding to 600 and still sealing it?

I don't pay alot for the exhaust parts, unlike the expensive pre-made Magnaflow direct fit exhaust system, with everything on it. I look at my existing exhaust layout, then get junk yard exhaust tubings, straights, elbows, flex pipe, flanges, hangers, resonator, muffler, etc. I got the larger sizes, instead of 1.75 inch, I got the 2.25 inch, then assemble it myself. Instead of paying $1000 canadian dollars before taxes, I got it done myself for drastically less dollars. I also get the mandrel bent elbows, magnaflow and borla mufflers, and nice chrome tips. The non mandrel bends are either crushed or wrinkled, while the mandrel bends are smoothly bent. I am going to use the Impala's dual exhaust axle back on the Uplander, with resonators in place where the Impala had its mufflers, since the van has its muffler, in the middle floor pan area, then add the Magnaflow muffler, and chrome tips at the end, coming up in the spring of 2025.

My old mig 140 served me well got a mig 250 and sold the 140 it's still welding to this day.

We gotta watch this for school

Nice job Brian and Eastwood. Great life story. We have so much in common. You are a great teacher and person for sure. We will definitely meet. Take care my friend.

very easy to watch and learn from. Excellent teacher. Thanks guys!

Greatest. Hairpiece. Ever.

tupang tuapng

I using a daewoo one that has the hobs on top to expand engine parts for years.... Cost like £30 in the UK...

I would hate that holes in the way 😢

So I can do body work after rolling this on?

She was way to far away while painting

When you switch to 100% argon, do you need to purge the previous gas mixture from mig welding out? Or does that quickly happen a few secs after you pull the trigger on the spool gun? Thanks

Love it.

I'm looking to buy this product to restore my Jeep's fender flares. After painting with this product on, would you recommend following it up with clear coat?

What is the grade of steel used in finger material ?

Thanks for these videos really learned a lot now I’m more confident making these repairs on my c10

yea that doesnt look very good.

What grade of clay bar should I use? I got me an overly hard one (the only one that was available locally) and it messed up my paint. Holograms everywhere. Never again. Good thing my car is white. Will an overly hard clay bar work on the windshield as well? Or should I go down to maybe a medium?

I did my last quarter-panel in the driveway. Go figure I got way less dirt than the garage !! Sometimes it's funny like that.

That ain't no door ding. You can clearly see the chisel mark the hammer you showed there left. Bahaha. Also, you should always sort the bodyline out first and then the dent (trim in this case)

N1❤❤

Ty

What grade of aluminum alloy is this, please?

that multi-purpose degreaser is pretty much brake cleaner in a way right?

Another greart explanation, thank You, but I have to ask something. If I have paint instructed to mix 5:1 (ex. 500g:100g) and I should add 30% of thinner measured by volume, does it mean I should add 30% of 500g or 30% of 600g mix :? PLZ HELP

juste one blue 20%lanthane.

Nice Thanks.

It runs like a water fall. U have to use it so sparingly it’s ridiculous

is it pitted and will this remove the pitting if its small enough

I agree skill levels have gotten better after years of trials.😂

I’ve been watching Brian since he started his channel ! My last two spray guns have been from Eastwood a Devilbiss Pro lite and just last week a Devilbiss DV1 old school clear coat edition. Many factors go into a great paint job I learn something new every time I spray in my home booth!

“It was painted black underneath the rust” 🤨

If you’ve got good penetration then grind it smooth bud

might need a bigger tip to help with atomization so you dont need as much airflow and end up with orange peel

Water and a tad bit of soap will be cheaper then the glass cleaner.

You may polish them too

Brian is awesome. Ive been watching for a while now and Ive learned so much from him.

This is lack of experience bud. Increase the stickout, problem solved with blowing holes. It’s a floor pan. No one will ever see it anyway.

so far, best intro video with great tips.

Thank you the clear and thorough explanation of all the step, settings and materials involved.

It gets sanded flat anyway who cares what it looks like in applications.

"im sanding the panel again, with 80 grit" unc YOU JUST FINISHED DOING THISS...

When do you expect the 4x8 table to come to market? I currently have the Versa Cut 4x4 Cut 40, but having to limit my cuts to below 49-43" is a drawback, but still an awesome table.

Rust only happens in UAW controlled states where they salt the roads to ruin the cars. Think "revenue stream".

💪💪

Ok. Lets say im going to paint my silverado. Do i have to mix my 3/4 in one shot. Or in parts. Sorry im new

Amazing job. Could you have only used the rotary ?

It's not just paint that's really irresponsible you get what you pay for I've been burned to many times doing budget friendly "CHEAP"!!!!!!!