9 ай бұрын
Пікірлер
@MonchiPlay_yt 11 минут бұрын
It doesn’t appear the usb option on cura
@kitsongaming8654 3 сағат бұрын
Thank you, never had this problem until recently so your a lifesaver
@getbent57 8 сағат бұрын
Would like to get into resin printing but don't really have a safe place to do that.
@subhumanvr6398 8 сағат бұрын
Yeah, good ventilation is a must for resin printers and laser engravers. Thanks for watching :)
@3dPrintedSoup 8 сағат бұрын
I have mine in a fume tent
@RachelAllan-b5u 8 сағат бұрын
I had the same issue with water washable- very brittle when it’s uncured .
@markhorneff2430 10 сағат бұрын
Never had this issue with water washable before, I think you need to dial the settings in for water washable as opposed to normal resin. Also I tend to remove the supports with warm water before curing
@3dPrintedSoup 9 сағат бұрын
Yes I changed to resin setting and yes I remove the supports before I cure- not my first rodeo
@3dPrintedSoup 9 сағат бұрын
Interesting you used it with no issues, which brand do you use, will have to give it a go :)
@markhorneff2430 8 сағат бұрын
I use the elegoo water washable resin, I print minis mostly and never really has an issue unless I dropped it😁
@kimadrianfroberg Күн бұрын
currently printing the tavern myself. in FDM on the Bambu lab A1. but it really is taking ages 😅
@3dPrintedSoup 20 сағат бұрын
Yup, it is a really big project. I’m still printing the roof!
@Blaze_Ninja 4 күн бұрын
I can't find cura?
@3dPrintedSoup 3 күн бұрын
Search for Ultimaker cura slicer :)
@Blaze_Ninja 3 күн бұрын
@@3dPrintedSoup thanks found it
@scannaunderscore1 6 күн бұрын
Not got WiFi connection?
@3dPrintedSoup 5 күн бұрын
Nope, this version has no onboard wifi.
@scannaunderscore1 5 күн бұрын
@@3dPrintedSoup I'll get the V3 KE one then
@gamehead6347 6 күн бұрын
Hey! I've been trying to print this out, I have all of the first floor printing just fine! Other than the third piece which prints the base mostly fine but once it tries to print the floorboards it prints them all to the left , under the furnace & pushes the wall way off to the left. I'm not sure why this is & it's been incredibly frustrating as the rest of the tavern has printed fine on my Creality Ender 3 V3 SE. I'm going to print it using automatic supports this time. I'll give an update if anyone is interested. Your tavern looks great btw!
@3dPrintedSoup 5 күн бұрын
Thanks for watching :) What’s the part number are you trying to print on the SE?
@gamehead6347 5 күн бұрын
@@3dPrintedSoup F1R3. I'm printing it right now with auto supports, I'll report back.
@3dPrintedSoup 4 күн бұрын
@@gamehead6347fingers crossed for a good print :)
@getbent57 7 күн бұрын
That part turned out really good. What kind of glue are you using?
@3dPrintedSoup 7 күн бұрын
2 part 5 min apoxy resin :) thanks for watching
@afteer 7 күн бұрын
dualshock is the ps4 controller. ps5 is called dual sense
@3dPrintedSoup 7 күн бұрын
That’s why the video is called duel sense.
@montanamaker4189 8 күн бұрын
Your hard work is appreciated!
@3dPrintedSoup 8 күн бұрын
Cheers :) thanks for watching
@ricardofranco4114 8 күн бұрын
was hoping for it to allow for the steam deck to lean further back.
@3dPrintedSoup 8 күн бұрын
Them contact the designer and ask him if he can make an adjustment, or jump on tinker cad and have a go yourself.
@alexcheng9278 11 күн бұрын
3:50 after pre heat where can I print. I can’t find the print button
@3dPrintedSoup 5 күн бұрын
You might have missed the drop down next to the slice button- click the drop down button and you can choose your usb printer :) Thanks for watching
@ShrekEngravings 11 күн бұрын
should i get an SE or a KE i have been considering them both i hope you can help me i have no clue what to get
@3dPrintedSoup 10 күн бұрын
I’d say this comes down to your needs and budget. The KE is the more advanced printer and is fast and detailed, however the SE is allot cheaper and although not as advanced, it still turns out a great print , just not as quickly . Watch some reviews- lots of comparison vids online. I don’t have a KE so not done one myself
@ShrekEngravings 10 күн бұрын
@@3dPrintedSoup ok thanks
@MattDonaldsonLive 11 күн бұрын
So cool. It beats the mug coaster I used
@3dPrintedSoup 10 күн бұрын
You use what you’ve got :)
@bobziroll 13 күн бұрын
Newbie here. I have an Ender 3, and when I choose "Pause Print" it doesn't move the nozzle to the home position but just freezes immediately in place on top of the print. What am I doing wrong?
@3dPrintedSoup 13 күн бұрын
It may be that you need to update your firmware to allow this to work, you can get the latest one from creality’s website. Thanks for watching :)
@user-xl7ry9xw3v 16 күн бұрын
I changed the board, in my Ender 3, from the original Creality board to a BTT SKR Mini E3 V2. Everything worked fine with the Ender board. However, with the new board (BTT SKR Mini E3 V2), my computer does not recognize / cannot find the Ender3 now. Any thoughts, ideas, suggestions. I am not super computer savvy or techy.
@3dPrintedSoup 15 күн бұрын
Hi :) as you have swapped the main board out, your printer may no longer be seen by your pc/cura as an ender 3 (not 100% sure as not used this board myself). Check with the manufacturer to see if the board supports usb input.
@kailroberto263 18 күн бұрын
Lovely video just make sure to mix your audio for both left and right
@3dPrintedSoup 18 күн бұрын
Thanks for watching :)
@Lousbro 19 күн бұрын
I was having problems with my sd card and this helped a lot but I’ve got a print going right now and I’m a little scared to do anything on my computer while it’s printing😂
@3dPrintedSoup 18 күн бұрын
As long as you don’t shut down Cura you should be fine. Maybe steer clear of resource heavy programs like graphic design or video editing . I use an old laptop as a dedicated printing computer.
@landonlama4365 19 күн бұрын
MAJOR UPDATE! Do not just buy a micro USB cable for this. I did that without checking. And it turns out my ender 3 has a mini USB plug. Don't waste money on the wrong thing when you may have one laying around.
@3dPrintedSoup 18 күн бұрын
Yeah, this has been discussed several times in the comments- basics, check the socket on the front.
@corbinianbenkiser6906 20 күн бұрын
Do you got any issues with running the printer really fast (250mm/s)?
@3dPrintedSoup 19 күн бұрын
Hi. I don’t run the printers I have linked up to my pc that fast so not sure if this would cause issues.
@ook-kc8mk 20 күн бұрын
When i type octopi.local into my browser. It fails, do you know why? I have powered the raspberry pi and plugged it into my 3d printer. My raspberry pi version is the zero 2 w by the way.
@50tantos 25 күн бұрын
This is nice, thanks a million!
@3dPrintedSoup 24 күн бұрын
Thanks, and thanks for watching :)
@getbent57 25 күн бұрын
Cool. That's coming along very nicely.
@3dPrintedSoup 25 күн бұрын
Thanks, looking forward to 2nd floor :)
@connorterror01 25 күн бұрын
8:15 ah the introductory line that I forcefully moved to the bottom center by modifying the gcode so that it was easier to remove on my ender 3 v2 😀
@3dPrintedSoup 25 күн бұрын
The line is there to ensure the flow is smooth and consistent, if you remove it fine, but it’s there for a reason. Thanks for watching and commenting :)
@Raikiln 26 күн бұрын
Was having problems with my SD/USB converter (which was brand new) so I appreciate the informative video that helped me get on my feet. Thank you!
@3dPrintedSoup 26 күн бұрын
My pleasure, glad it helped and thanks for watching :)
@montanamaker4189 Ай бұрын
Great video!
@3dPrintedSoup Ай бұрын
Glad you enjoyed it
@nza. 27 күн бұрын
@@3dPrintedSoup hey i need help with my ender 3 v2 neo. so just today some filament got stuck in the bowden tube and i dont want to replace it but i dont know how to get it out. some filament also got stuck in the extruder when i was trying to pull it out. can you help with a video or osmething please?
@3dPrintedSoup 26 күн бұрын
@@nza.Hi. unfortunately i don't have a neo so am limited to the help i can provide. However, as this is a blocked tube and extuder you should be able to pre heat the hot end, remove the tube and use a stiff bit of thin wire (most printers come with one included when you buy it) and use that and clear the nozzle. Then remove the nozzle while still hot (be careful!) and then remove any molten or burnt bits of plastic with needle nose pliers (turn off the power before you go routing around though, just in case). Then push a bit of filament down the bowden tune to get any stuck bits out and you should be fine. Thanks for watching.
@nza. 26 күн бұрын
@@3dPrintedSoup thank you ill get back to you!
@getbent57 Ай бұрын
That's cool. Looking forward to seeing all the parts together.
@3dPrintedSoup Ай бұрын
You and me both! Thanks for watching :)
@Shaozimi Ай бұрын
Does the raspberry pi zero 2 w work with this method? I also have the ender 3 v3 se but i do not know where to plug it into (the raspberry pi)
@3dPrintedSoup Ай бұрын
I have never tried it with a zero, but if there is a version of octoprint for it then it will work fine. As to where to plug it it, watch the video , it’s all in there. Thanks for watching
@edwinbarton2285 Ай бұрын
You stated that pause worked nicely from the network, however you weren't connected over any network you connected over USB. Are you going to redo this using an actual network connection?
@3dPrintedSoup Ай бұрын
Watch the octoprint video I uploaded, thanks for watching :)
@juampynieto7277 Ай бұрын
Thank you very much, I didn't know that from the "Creality Slice" program you could connect. You're a genius. Luck
@3dPrintedSoup Ай бұрын
Yes,yes I am. Thanks :)
@ook-kc8mk Ай бұрын
Just a question (or two). My 3d print always stick to the bed and are really hard to remove. Do you know how to make it easier to remove the prints. I usually make supports at the bottom so they will go off easier but that wastes my filament and it gets messy. Do you know a method to get them off easier?
@3dPrintedSoup Ай бұрын
Several answers for this one, the easiest is to let the print cool, the print should shrink a tiny bit when it cools, this helps the print release from the print bed. Get a flexible print surface if you can, these allow you to bend and warp them till the print comes free. Finally, a metal flexible print bed with no. Stick coating really makes life easier. Of course these tips are for filament printers, you don’t say which type or brand of printer you are using. Hope this helps :)
@ook-kc8mk Ай бұрын
@@3dPrintedSoup Thanks very much!
@alonsocambronero5663 Ай бұрын
On a FlashForge 5m Pro I was able to cut the filament about 1 inch before the extruder, and loaded the new filament while pursuing the print head without pausing the print. Not sure if I would be able to repeat the feat again 😂😂
@3dPrintedSoup Ай бұрын
Wow, nice effort :) I did the same with the first ender 3 when first got one
@erlangame0129 Ай бұрын
Can you make a ps2 gold Gundam stand pls
@3dPrintedSoup Ай бұрын
If you have requests then sub to the patrion :)
@sinetwo Ай бұрын
Your intro had me! You are 100% correct, I am propping it up against a full water bottle, and I don't want Jeff Bezos to send me some BS :D
@3dPrintedSoup Ай бұрын
Glad you enjoyed it :) thanks for watching
@Neonbrain. Ай бұрын
Excellent I'm a new 3d printer owner thanks for your help keep up the good work 😊
@3dPrintedSoup Ай бұрын
My pleasure- good luck on your printing journey :) thanks for watching
@dougprw1110 Ай бұрын
Worst video I've ever seen to demonstrate how to do something. Our view is always blocked during the actual steps of how to do what he's demonstrating.
@3dPrintedSoup Ай бұрын
Thanks for watching, it really helps :)
@miniworld3d Ай бұрын
Hi, Dany Sánchez here, thank SO much for your video review! More than happy and proud to have come across your video, I'm glad that you liked my model this much, your words are the reward for the hours and hours of effort put into it. Cheers!
@3dPrintedSoup Ай бұрын
He still sits on my shelf , really enjoyed printing your design :) .
@boredfish80 Ай бұрын
This is really cool :) the only thing that kinda bugs me a little, though - you've clearly gone to a lot of effort/expense (relatively), built the entire cab with 3D parts to get to a pretty cool looking product, only to finish with a cardboard frame for the screen. Why? 😛
@3dPrintedSoup Ай бұрын
Because I had a Perspex screen ordered from Germany that got lost in transit and did not arrive in time for the video, sooo frustrating! Thanks for watching :)
@erickruse4679 Ай бұрын
To get it to print via USB, I had to actually download this Ultimaker Cura software specifically. The software Creality software that the printer came with wouldn't do it via USB, and when I clicked the auto-update button, the new latest version of the creality software didn't even have this printer in the list...><
@3dPrintedSoup Ай бұрын
Yes, as I mention in the “what you will need” section , you need the latest version of cura. Creality expect u to use their WiFi box. Thanks for watching :)
@jumanjiserviciosTMC Ай бұрын
Hi..thanks for the video..the principal issue is that you need your pc always on...is there a way to send files to the microsd without extracting everytime the card? something as a shared folder ? or can you try if your pc shows the ender "disk" at my pc? avoiding of course needing some raspberry...thats not an option haha
@3dPrintedSoup Ай бұрын
Hi! I really wanted this to be an option, unfortunately there is no way to access the sd card from the pc, you have to send the Gcode from your computer to the printer directly. Cheers for watching :)
@falconNL Ай бұрын
How does this compare to your Creality? Is the bed any bigger?
@3dPrintedSoup Ай бұрын
The print surface is slightly bigger, but the resolution and level of detail is soo much better. The 8k screen turns out amazing prints.
@thevannut Ай бұрын
Looks like a fun new printer. I bought Ender 3 and the latest Ender 3 v3 only after watching your videos. Amazing machines, love using them. But quality on miniatures for d&d with resin... awesome! Happy Father's Day.
@3dPrintedSoup Ай бұрын
Cheers matey , glad you enjoy the videos :) resin is the best option for mini printing, the level is detail is amazing. My ender 3 v3 is working full time making some large dnd buildings at the moment.thanks for watching
@dustinsandoval7373 Ай бұрын
What app or program do you use
@3dPrintedSoup Ай бұрын
All the info is in the video :) happy printing
@getbent57 Ай бұрын
Elegoo make great printers, own two.
@3dPrintedSoup Ай бұрын
I’m enjoying it so far
@und1n Ай бұрын
Hi, thanks for the video, I'm watching you. Please tell me how do I print from OrcaSlicer to Ender 3 v3 SE over a USB wire? Only with the help of Reality Wi-Fi Box 2.0?
@3dPrintedSoup Ай бұрын
Hi! Thanks for watching. I don’t use the creality WiFi box as I have octoprint so I don’t need one . Not sure if you can use the creality box with other slicers.
@und1n Ай бұрын
@@3dPrintedSoup That's probably not how I expressed my thought. I want to connect my Ender 3 v3 se via type-c - USB-A cable to my computer and run the OrcaSlicer slicer, but in OrcaSlicer I do not know how to set up a connection to the printer via cable, is it possible?
@GunsRocket 14 күн бұрын
@@und1n Hi! Did u solved it? I need it too
@und1n 14 күн бұрын
@@GunsRocket No, I've left this problem and am using an sd card.
@mineandforever2877 Ай бұрын
Thankyou for your video i been trying for a week to use that sd but it now working though my usb and printing it first model of a cat
@3dPrintedSoup Ай бұрын
So glad I could help :) hope the cat turns out purrr fect ….sorry ;) thanks for watching
@mineandforever2877 Ай бұрын
@3dPrintedSoup it all good now I worked it out plus you video helped yes came out flawlessly I'm now I have few great prints already how quick it is and amazing the level of fine detail it able to purduce with the filament types
@martinconnolly2995 Ай бұрын
How do you connect to te network ie if there isn't a PC right next to the printer?
@3dPrintedSoup Ай бұрын
By watching this video kzbin.info/www/bejne/bKmxe6SnpMaCms0si=WGzG1Vqn9u9ihkw1