PookyThomas

Пікірлер

@Tatonka322 13 күн бұрын

You just needed to add a fuse circuit, you don't need to cut and splice any of those wires. kzbin.info/www/bejne/fqndl5-ZoqiBoJYsi=JZh-c8leFg10R5UI

@pookythomasmoto9147 13 күн бұрын

@@Tatonka322 I did this video years before the plug and play system was a thing. I purchased the harness for my second navi and did it that way.

@TheMotoMax 29 күн бұрын

Do you need that key though?

@MoviePireShorts Ай бұрын

Can anyone please link to the amazon page where this key was on ive been searching for an hour couldn't find id

@MrJIZZYCEE Ай бұрын

Hey man it's the dude who met you at that trick or treat spot!

@pookythomasmoto9147 Ай бұрын

@@MrJIZZYCEE Awesome meeting you! You’re the first sub I’ve met in real life

@tobiastrotter6449 Ай бұрын

You are very smart

@kc1800party Ай бұрын

thanks for being a great honda navi resource, i appreciate it. quick question: what did you connect the ground to? i have to use the frame since i don't have a spare ground just chillin

@pookythomasmoto9147 Ай бұрын

@@kc1800party there is a bolt that holds the headlight bezel frame on. It’s an M6 and I took a battery terminal connector and linked the wire to that, and then threaded the bolt through it

@kc1800party Ай бұрын

@@pookythomasmoto9147alright i think i know which one you’re referring to. thanks bro!

@kc1800party Ай бұрын

@@pookythomasmoto9147 my bad bro, i just rewatched the video. my dumbass didn't get towards the end which would've answered my question haha. that was exactly the bolt i was looking at too. thanks again.

@adventures_of_topher Ай бұрын

All

@adventures_of_topher Ай бұрын

Amazing detailed video… You are going places in life!

@Joejoe.999 2 ай бұрын

If the carb bumps the rpm and gooses the cvt while your kickstand is down your bikes gonna dump itself😂 This is a brainless mod

@pookythomasmoto9147 2 ай бұрын

@@Joejoe.999 So let me get this right. “If the carb bumps the rpm and gooses the cvt”. What I’m understanding is you think I have a sticking throttle? Because I do not. Secondly, with the choke on warm up it’s not enough to send the bike forward as the CVT engages at rpms slightly above what a cold start high rpm climb does. Explain your tweaking to someone else PLEASE. Thanks for watching!

@Joejoe.999 2 ай бұрын

@@pookythomasmoto9147 😂😂😂it’s better to remain quiet and have people think you’re a fool than to open your mouth and remove all doubt pooky. Just put the bike on the center stand and it does the exact same thing you are trying to do without any work or deleting any safety features at all. You’re the real special Ed

@Joejoe.999 2 ай бұрын

@@pookythomasmoto9147 the center stand does this with zero mods to safety features. Your welcome.

@Makeshifthalo87 2 ай бұрын

Just curious I have a 2024 honda navi and I was told not to use synthetic oil just the 10w30 motorcycle honda oil.Does it matter really?

@Makeshifthalo87 2 ай бұрын

Want this done to my navi i know its easy to do but im no mechanic lol definitely would pay someone to do this plus after this mode there is tunning as well.

@Ultraaaaaa 2 ай бұрын

Can you send me a link that currently sells it...that is available...I loved your video, long life to you with much happiness

@richbanks1479 2 ай бұрын

Navi NAvi NAVi NVAI

@MrJIZZYCEE 2 ай бұрын

hey man are you on 603 riders by any chance???

@xCARPx2014 3 ай бұрын

Where did the black wire come from?

@JunkMan718 3 ай бұрын

Awesome build. How did you power up speaker? Also did you have a bluetooth /amp to be able to get sound out speaker?

@Lewis_Ald 3 ай бұрын

This is definitely the better version of the under seat indicators I’ve seen, my only question is how the hell did you wire the brake led lights up to not be a DRL and only work off the brake pedal?…

@pookythomasmoto9147 3 ай бұрын

@@Lewis_Ald the three wires going to your taillight, running, brake, and ground. I only spliced them into the brake light circuit, and each turn signal to their respective sides as well

@JayKing-tj2et 3 ай бұрын

having the same exact problem thankfully i finally found this video of your, i only need to buy one of these yoshi diodes not 2 pairs correct?

@pookythomasmoto9147 3 ай бұрын

@@JayKing-tj2et just one like I used in the video

@JayKing-tj2et 3 ай бұрын

hey brother i really appreciate all your navi content but i am having an issue with mine that im sure you have an answer too you briefly touched on in this video. so i did the ac / dc conversation, upgraded the flasher relay and currently have led headlight bulb, led front signals, led rear taillight from reckless customs with integrated turn signals and i also upgraded the speedo bulb to a bright white led. i tried installing an led bulb for the turn signal as well but ran into the same problem that you showed here in the video where it does not work only one side works and if you flip the bulb 180* then the other indicator side will work but not the previous one so yes can’t run an led bulb for the turn signal indicator and i’m fine with that however the problem i am having is that if i plug the stock indicator bulb back into the turn signal socket then when i hit the switch to activate either my left or right indicator all 4 of my actual turn signals all flash simultaneously. how do i fix that so that when i indicate left or right all 4 blinkers don’t hazzard flash with the stock turn signal indicator bulb in?. i have been trying to find videos on here or checking online forums and facebook groups but no luck so far it seems like yours are working perfectly fine so if you could help me please 🙏🏼

@pookythomasmoto9147 3 ай бұрын

@@JayKing-tj2et so it sounds like you are missing resistors. I personally did resistors on each turn signal themself, but I have heard you only need them in the front. Resistors prevent back current from tracing all 4 turn signals in the harness. MNNTHBX website has them and I believe Yoshimura does as well. Look up “LED RESISTORS”. Hope this helps.

@JayKing-tj2et 3 ай бұрын

@@pookythomasmoto9147 i found your diode video after i had already left my previous comment and that’s what i ordered the same yoshimura one that you did that’s different from a resistor? i have an upgraded flasher relay and it says not to install resistors if running an aftermarket turn signal flasher relay so hopefully the yoshi diode fixes it all.

@tripwheelerton2417 3 ай бұрын

You can do this without removing the upper panels. Engine vent plate, top floor plate and then lower plate. Stop stripping screws you all don’t need to.

@pookythomasmoto9147 3 ай бұрын

@@tripwheelerton2417 Considering the footrest area of the top floor panel sits behind the side plastics, removing the side plastics is a must if you aren’t in the interest of scratching or prying plastic pieces around one another. Also, I wasn’t aware I stripped any screws! I’ll have to look back and check them.

@johandow1006 3 ай бұрын

Could you drop a link for the intake box delete plz 🙏 😅

@pookythomasmoto9147 3 ай бұрын

@@johandow1006 I have a whole video on it

@johndove2604 3 ай бұрын

What's that LED model that doesn't need a conversion kit?

@pookythomasmoto9147 3 ай бұрын

@@johndove2604 I think it was sealight. You don’t have to do the conversion for LED’s to begin with.

@JayKing-tj2et 3 ай бұрын

so what did you do with that welch plug? where does that need to be adjusted to? that’s the only part confusing me.

@KrazEEnis 3 ай бұрын

This speaker doesn’t look like it’s Bluetooth. Where are you getting your music from? Or how?

@liuhongqian 4 ай бұрын

Why youtubers don't list the oil and nuts link under the video...

@pookythomasmoto9147 4 ай бұрын

@@liuhongqian why people can’t search the oil used in the video on google or amazon… crazy how the internet works.

@BeeStingPS3 3 ай бұрын

Agree because different climates require different oils

@lorenzomillet 4 ай бұрын

Bro just want to say great job, I'm glad it was as long as it was. Thorough explanation of how it works, honestly think I have a better understanding of how carbs and my Navi work now. finally got my navi running properly. Good vid 👌🏿

@heith85 4 ай бұрын

I've had other motorcycles and when I got my Navi back home in my truck I wanted to start it and thought the battery was dead. Spent way too much time trying to kick start until I realized the kickstand shut off. I will do this mod as I want to start and let it idle with the choke as I gear up

@jorgeandrade2997 4 ай бұрын

Nice

@xCARPx2014 4 ай бұрын

Which one is the high beam indicator bulb? I can't seem to find it, unless it's under the white plastic.

@pookythomasmoto9147 4 ай бұрын

@@xCARPx2014 You are correct! So if you take off all 4 small Phillips screws and slowly pull the speedometer layout itself up (after removing the clear plastic cover) you will see a green filament and a blue filament. The bulbs are yellowish but the filament plastic cards dye them. The bulb is hard wired into the speedometer and is not able to be removed unfortunately. You can, but you will have to get quite creative.

@xCARPx2014 4 ай бұрын

@@pookythomasmoto9147 damn, I wanted to have all blue LEDs in there lol.

@ryangraham729 4 ай бұрын

Does not affect 2023 navi or after..

@kennywheelus6857 4 ай бұрын

😮,nice after you got the right size housing for led headlight bulb,wow, world of a difference between night night an day, definitely have more visibility now with that mod,best one on here I've seen,ty,I know now if get my girlfriend this bike an do these mods shed be able to see better if she chooses to go night riding.

@kennywheelus6857 4 ай бұрын

What company an part name for the tail light,I've been thinking about getting this bike for my girlfriend,but I don't like the dim headlights,so I've been watching people do mods on this an how to make it faster,next would be to improve the breaks

@dylansouza122 4 ай бұрын

I thought it was going to be a lot more work sweet

@duelavemedia3565 4 ай бұрын

Can I get a list of your Navi products

@xCARPx2014 4 ай бұрын

What about the highbeam indicator?

@pookythomasmoto9147 3 ай бұрын

@@xCARPx2014 you have to switch around the wires that lead from it. Something like green to white and blue and the other to the opposite

@MrSizzleDrizzle 4 ай бұрын

Thanks for sharing this information, its very informative. Although i think what would be better is if in place of the key there was a hidden switch. I say this because all it takes is for you to lock the bike with the key and someone to come along, see the ignition barrel, locate the wires under it, snip them which would then render the key in your pocket redundant and the bike would start. They don't even have the trouble of connecting the red and black together which is great for them as it saves them a step. What i suggest for anyone thinking of doing this is to use the exact same wiring but wired to a hidden toggle/push button somewhere on the bike. This saves the hassle of trying to find an ignition barrel like the one in the video and saves you from the potential security weaknesses that come with it. Two things will happen, either the thief will realise theres a hidden kill switch, which will take too long to figure out and deter them, or they will think the bike doesn’t start and cut their losses and move on. Thanks again for the video.

@ricktaylor26 5 ай бұрын

You explained it much better than others have. Good job . What did you need to do to get the back turn signals to work ? If anything Thanks

@pookythomasmoto9147 3 ай бұрын

@@ricktaylor26 the left side and right side turn signals run off the same switch. So if the front is working the rear should work on the same side. You may have a wiring issue

@flyinphil42 5 ай бұрын

Would a #120 main jet be too much ?

@vincentsleeves2810 5 ай бұрын

Was watching this video trying to figure out what to do, put on yoshi exhaust and polini air filter, and then bike wouldn’t start. Did the install with boyfriend, a few mins into the video when you said “turn the fuel off” and then he said “oh I already did that” 😂😂😂 no wonder it didn’t start!