You did a good job

To do a good job

I'm not a mechanic by any means but this looked so easy to do I did it myself and fixed my generator! Its purring like a brand new one. Thanks for the video! Happy New Year!

⭐⭐⭐⭐⭐Thank you.

in your post the photo shows a red circle around the fuel tank shutoff value but NO info on how to service that??

What is the model# of the inverter?

May your nuts grow big & hairy.

Did you replace the tank? How much does the tank cost?

Found out today that My oil pan is leaking from the front, I may try to remove my oil pan like this. Not sure if i need to remove my camper shell to tilt the cab though.

is it the one from @southern Biker ?

WOW! WOW! You are a GREAT instructor!! Here is my gift in return. The brass tube with a bunch of holes that is attached to the main jet is called the "emulsion tube" (or sometimes called the "main air bleed tube"), according to CoPilot. THANK YOU!!

I have a Kipor IG4300, and it stops making power and I was wondering if Champion makes a control board that would work with the IG4300 (4,000 watt) model?.

is it possible to only replace the front fairing (headlight / windscreen area)

My 03 yamaha vstar 1100 does the same thing whay is it or why did it just shut off when I'm riding?

This is why I never buy anything from anybody wearing cargo shorts & sandals or flip flops. I've always had bad luck from those dudes. When buying, always have a pick up truck with a full size 8' bed to haul it home. Then sort it all out.

Did you remove the turbo?

Thank you so much! We can return the new carburetor we just ordered thanks to your great video.

Appreciate you! Exactly what I needed.

don't let wetbax & retardz ride MC's

Emailed you !!! Please reach back out

Great video! 200 hours on my 3500. At 100 hours it was surging and then stopped running all together. I bought a replacement carb from Amazon (they're cheap enough) took me 3 hours for the swap. At 200 hours I had the same issue. Back to Amazon for another carb - this time did the swap in 20 minutes. Always faster the second time.

Ur r so awesome beautiful I learn so much it's like going to generator repair school thank u from eastern Oklahoma GOD bless

couple questions will the new gen fuel gauge just not work at all with the old gen r6? like what if i installed a starlane cluster and used the new gen r6 fuel gauge

hey man, can you list down the parts you used? i wanna do this but i'm kinda lost in where and which parts to buy

on a propane set up, do you still need to PRIME it ? Mine is turning over but does not fire. Is there a propane line " cut off switch" im missing somewehre ? fresh propane tank as well and both valeves at the tank, are open

Dude your a bad mfr! 👍🏽👏🏼💪🏽

Need to adjust you camera so we can see what your doing

Needle nose pliers 😂

You have the best videos on the problems and fixes of the Predator 3500. Your way of teaching and sharing, in my book is the best on KZbin. Do more when you cab of different projects and tell us what you are doing in the real world.

Unbelievably helpful. Great video on the Predator 3500 carb.

Sometimes when your fuel pump gets hot it can not work properly so the trick when you hold prime to see if it’s pumping fuel only goes so far. Great video btw I like how you really showed each step.

I have the identical generator and identical problems that you have with the one you repaired. My question is why is the board bad and not the brushes or AVR, etc? It’s a very helpful video! Thank you.

Hi can you please tell me the inverter parts number I need one please

So what gen r6 do u even have

Saved me nearly $600. i tried a $50 Chinese knockoff but it wouldn't hold idle or trigger the transfer switch. I decided to try to clean my original before ordering a new carb from a local dealer. After watching this video I had the gen up and running again and all systems are functioning normal. Thanks so much!

Have you worked on a lot of these? Do you find the valves are too tight often? Great video!

Well done

Wow you’re one impressive young man! I’m a new subscriber! My 3500 has an idle problem whereas under no load it surges faster and slower. It never dies but it hunts for the right idle. Would that be the slow idle jet that needs cleaning? Under load, it runs great and is very smooth and strong.

ik this is a old video but do u think you can do this conversion with a 2003?

ik this is a old video but do u think you can do this conversion with a 2003?

I have a Champion 100263 Inverter Gen. It has about 6 hours on it. I had no run it for a while. When I started it... it had an oil leak. What can I add to the oil as a stop leak?

20:00 "Polarity doesn't matter"? That is hard to follow, especially if you connect two inverter generators in parallel. What readings do you get if you measure voltage ground and the two sides of the 120v receptacle? You know in household wiring, you get 120V on one side, and zero on the other.

😁

Thanks for the video

Awesome video just found one for free got it running thanks to you! Great tip at the end; Drain your gas save your generator!

Thank you so much. We're getting ready for Hurricane Milton landfall tomorrow. My friend, who has a 23 year old son paralyzed from the neck down, needs this generator to get them through. Your video was so helpful, although I wasn't able to get the jets out because of lack of a right sized screwdriver as well as that black plastic screw....I didn't want to screw with it. So we loaded it up with new gas a lot of sea foam and used a lot of carb cleaner through all the ports, and it's running great. Little hesitation here and there so we'll let it run hot for a while and let the seafoam do its work. Thanks so much. Blessings. Jeff

Thank you, Thank you, Thank you! Mine would not start as well. Cost me $6 for a can of carb cleaner. Hurricane Milton is currently coming at us in Florida! I’m glad I found your video!

This is the second time this video has saved my bacon - and just in time for Hurricane Milton! Thanks from a Florida resident!

This is embarrassing

this kid is good. 😄😄👍👍