I have the opposite problem, my condenser fan non stop running even coprocessor turn off by thermostat. What is the wrong.Thanks.

Jesus Christ the first five and a half minutes of my life wasted watching this video FFS man you’re ment to be teaching us how to. Not telling us your life story know one is interesting just get on with the dam teaching. I have learned nothing from this video because of I had turn it off after the first five and half minutes. So f- ing boring.

Great video series but please stop with the story telling get on with showing how to bend the dam conduit .

is this work in big skin tag?

What is a "gosan chart"?

By far, the clearest, most concise, and speedy to watch videos on KZbin. I wish I had someone like him 50 years ago when I was an apprentice to tell me these things.

2 of the outlet boxes are crooked and all 3 are not the same height...

Omg I want to go see this!

Since you do not like 'lego nuts' and keep telling us to not use them, do you have a video where you do not use them? Also, I bought this house and have been correcting all sorts of things. This one is just like the problem you are demo-ing. I have a problem where I cannot seem to find the load's neutral wire. Apparently, i found that the GFI was being bypassed. Nothing on the GFI's load connections. So, do you have a video where you do not use lego nuts? thank you.

Thanks. How regularly should you staple Romex? For example, how many inches should there be between staples? And how much length of Romex does bot require a staple?

You can install as many GFCI's as you want on one breaker.

Fan error, but the inside unit sounds like it's trying to kick on intermittently. Any ideas?

Thank you for making this

You got a new sub with me. I too love my kleins made in USA drivers. Even the ones made in Taiwan are amazing.

Why did the old timers with two prong house system run grounding wires behind the electrical boxes ? My copper pipes and white wires have continuity. I have no ground wires in the house .

Question : on a basement gfi outlet and a second outlet/switch combo that I just put in , I’m getting a solid tone on one of my ground plugs on the gfi. I thought it was getting powered volts somehow. I tested the gfi and it says it’s ok. I tested with a multi meter and have 3 volts On ground. Strange? The other ground has broken slow tone . Do you think the fast tone was just transient voltage on the ground plug ?

I can't remember the brand, but the one I used in the past, had a striking ball on the end of the stud that protected the threads.

What is the recommended wire nut size/color (whatever spec necessary) to wire together three, 10ga solid Cu wires?

Love your tutorials. EZ to understand for even a DIY er! like me!!!

Super video thanks

do you have 5 minutes videos ? they are useful during work to get something done

Thanks for this

Thank you for the way you teach how to wire a gfci switch combo. I tried to install one 2 days ago; the light stayed on. After watching your video, I installed it correctly, and it works fine. Thank you for sharing your knowledge 🎉

So basically...line power for both hot/neutral wires from the panel goes to the LINE side only of GFCI 1 and the LINE side of GFCI 1 also feeds LINE side of GFCI 2? LOAD side IS NOT used on either GFCI? So LINE feeds LINE? Is this correct?

Awesome video! Thanks

90 degree to a 10 degree

I am building out some sound proofed rooms in my basement using resilient channel and 1/2 in dry wall which will put my stud faces 1 inch from the wall face. should I use these boxes or is there another better option to get the box 1 inch out from the stud face?

Good thing about these blackout screwdrivers is that if no one else on site had these you can easily distinguish they're yours. Bad thing is that they can easily be forgotten in the cieling and never to be seen again

Thanks man was cursing up a storm for the past few hours until I came upon your video.

Then why is it so expensive?

u said near the end that this is not your #1 favorite.... which light is #1 ??

Thank's

Good

For some reason this capacitors go bad on weekends only. No one has then.

love watching you videos

Congratulation

Put a strip of duct tape along the side that goes into the dishwasher . Temporary fix for me turned into 0 leaks for years for a poorly constructed part

Thanks for show how to open clip on new set

thanks for sharing

getting mine tomorrow

you do recommend great items, thanks

What is open neutral

Used to work with this guy, idk how he’s doing now but he used to be a huge alcoholic

I like your videos. You do a good job and come across as humble and approachable. I watched some of your videos when I wired up a 4k sq ft shop 2 years ago. I'm doing another one now...thought I'd see if I could learn some more, so, I'm back. Thank you for the time and effort to share your knowledge.

I like it

thanks again!!

*:20 kick ass trick !! thanks

new subscriber, great video

You had the camera pointed at a bad angle for most of the time. We don't want to see your face we only need short clear information and with good camera focus. Chris Fix never shows his face on the Camera because he is smart enough to know his job is to perform automotive Repairs and installations and verbalizing all the appropriate information. This is why he is the most watched Mechanic on KZbin etc.

Leaving the nut on can and will compact the threads.