8 жыл бұрын
8 жыл бұрын
Пікірлер
@mustang1100 3 ай бұрын
Unbolt the torque converter would saved u a lot of headaches
@peterscalone6167 Жыл бұрын
Is that process simular to a 2012 Dodge Challenger V6?
@MTFOphantom Жыл бұрын
Hey man outta curiosity what was that guide on your computer screen with the diagrams on what you needed to do? That seems extremely helpful.
@kurioca195 Жыл бұрын
It's called AllData. It's a paid service but absolutly worth the money. I only recommend paying for it if you're working on a huge variety of cars. Other wise I'd suggest finding a local shop and asking them if they can print you out the AllData repair sheets. Some shops might use another program called Mitchell, personally I preferred AllData, as it just looked better to me.
@MTFOphantom Жыл бұрын
@@kurioca195 Wow man, seriously, thank you. That info is incredibly useful. Im gonna hage to look into that.
@4FIVEHD Жыл бұрын
my 08 motor just lock 0n my charger
@robbievallance1044 2 жыл бұрын
Seeing that torque converter being pulled out of the trans like that... Cringe... you know the pump bushing on the trans took some damage
@kurioca195 2 жыл бұрын
I did not as this was years back, but that's okay, I can see how and why that could've been damaged and thanks for the input. I'll make sure if I ever do that again to consider that.
@chrisruth2040 2 жыл бұрын
Did you have drop transmission to remove engine
@kurioca195 2 жыл бұрын
Nope
@chrisruth2040 2 жыл бұрын
How did you rig chain to lift engine? Is there any lifting points?
@kurioca195 2 жыл бұрын
Off the top of my head I don't quite remember, I can say though from the looks of it, I found bolt holes on the engine block itself. I just used the original hardware that was already on the engine. When fitting the chain I usually keep the bolts loose until I get the right placement then I tighten them up and hook it up to the hoist.
@waltercartagena5830 2 жыл бұрын
should it just dropped the trannny saves a lot headeaches
@William1987GTA1 2 жыл бұрын
3:13 That PCP valve is cracking like Hunter Biden!!!
@johnwelsh2497 3 жыл бұрын
Yeah, need help pulling the front transfer case and passenger side drive.
@johnwelsh2497 3 жыл бұрын
Was this an AWD? I don't think I saw anything about pulling the 2 front drive shafts.
@kurioca195 3 жыл бұрын
No only rwd
@kurioca195 3 жыл бұрын
No only rwd
@superbowl32 3 жыл бұрын
Ruined it by cranking music so loud
@drewv8059 3 жыл бұрын
Thank you for sharing your work! It is much appreciated 🙏
@JesusSanchez-xb5ok 4 жыл бұрын
Can you tell me where exactly is the engine cooling time sensor plug goes?
@MrJoeG-be8er 4 жыл бұрын
around how much you charge for that
@xavierlewis2010 4 жыл бұрын
Wire harnes removal Dodge Magnum
@robertbobbypelletreaujr2173 4 жыл бұрын
Great video. To the point, in plain english and no lags/good cuts. Fuckin genius dude. Respect.
@kurioca195 3 жыл бұрын
Thank you so much for the support!
@raymondherbert3960 4 жыл бұрын
ANY TIME YOUR WORKING IN THE ENGINE COMPARTMENT, A REAL PROFESSIONAL, USES FENDER PROTECTORS , SO NOT TO SCRATCH THE PAINT OR EVEN DENT THE FENDERS. HELLOOOOO
@wilbornv2 5 жыл бұрын
How long did this whole process take?
@carll.freemanjr.9867 5 жыл бұрын
The only sizes you need are a 17mm and a 14mm
@ambrosiohernandez2898 5 жыл бұрын
Is this the same process for a 2004 Acura rl?
@s_class7027 2 жыл бұрын
Yeah
@crusadershuakbar 5 жыл бұрын
i have a question, 91 wa model, same same, i`m getting a serious shuddering when under load, 3rd gear around 4000 rpm, i suspect it may be the inner bushings, as i have recently installed new outer bushings ( sway bar to control arm) ball joints appear ok. question is, to replace the inner bushings do i need to remove the entire hub assembly etc like you did, or can i just remove the inners bolt ,pull the arms inner end down a bit and beat the old bushing out and install new kit and jam it back up and wack the bolt back in ?
@davidbender2950 5 жыл бұрын
Do i need to support the trans
@ericasutherlandhayden6222 5 жыл бұрын
yes, you do. i just did removal and putting a new engine in my husbands car. we just used the jack with a small piece of wood
@kalisiklow7259 5 жыл бұрын
Can u post the link to the webpage you were using plz!
@kurioca195 5 жыл бұрын
Kali Siklow the program I used was called alldata. It’s a monthly subscription to the database that has every vehicle on it. Just google search alldata
@businessman953 6 жыл бұрын
nice work girl and all by your self mami chula rrica.
@timburton199 6 жыл бұрын
my son blow his 2.7 up so we got a 3.5 engin with a 5 speed tranmission the 5 speed got 2 wires the 4 speed got 4 how to hook the 5 speed to the 2.7 wireing harness
@raymondherbert3960 4 жыл бұрын
DUHHH, YOU FIND THAT STUFF OUT BEFORE YOU GO OUT AND BUY A DIFFERENT ENGINE !!! YOU ALSO, CHECK YOU STATE REQUIREMENTS BEFORE EVER STARTING SUCH A PROJECT. IN CALIFORNIA, YOU WOULD NEED ALL THE SAME EQUIPMENT FOR THE 3.5 ENGINE, THAT CAME IN THE CARS THAT CAME FROM THE FACTORY, IN INCLUDING THE CAT. WHEN DONE, YOU HAVE TO TAKE IT TO THE STATE INSPECTION CENTER, TO GET IT APPROVED TO BE LICENSED TO DRIVE IN CALIFORNIA. GOOD LUCK.
@robwells5753 4 жыл бұрын
Cut the extra wires off you dont need them
@stonewall381 6 жыл бұрын
What website was that ..
@DLsGameGuides 4 жыл бұрын
DJ Stonewall alldata
@stonewall381 4 жыл бұрын
Im bout to do mines saturday this week.. Look on my page for details later
@shelovesquanny3522 6 жыл бұрын
U gained a sub just cause I got the same exact car and computer
@warbed1 6 жыл бұрын
For those that don't know cant remove the torque converter when you cant rotate the engine when its locked up. Why they didn't remove it in this case is because they don't know what there doing. Sorry but it's true. It's a 2.0 hour job max to remove.
@kurioca195 6 жыл бұрын
warbed1 cool 👍
@user-zt4yk1sm8y 5 жыл бұрын
warbed1 Do you think it's faster to remove the front bumper and radiator? Instead of messing with the wiper motors and cowl. Blueprint for the 2 hr removal?
@user-zt4yk1sm8y 5 жыл бұрын
It's faster the way Garden Style did it I just did one and I had to pull the trans with the engine so I took the whole front off and btw if you're doing the trans you need a 3/8 drive t60 for the driveshaft bolts they suck especially no lift Appreciate the video
@xdaro1979x 6 жыл бұрын
what's the difference between 2006 3.5L and 2008 3.5L ? I have a 08 with bad engine buy when I do search only 08-10 engines come up. 2006 looks exactly the same . what has to be changed / transferred from 06 engine to work for 2008 ??
@everydayrc1783 5 жыл бұрын
I got a bad 08 3.5l and looking I'm at an 07 for a replacement. The engine looks the same to me except the intake. Seems like the 08 has a block off plate on the left side of the intake (looking at it from front) where the 07 has some electric valve or such. How did you make out? What year engine did ya use and any issues?
@Flatlandproductionz 2 жыл бұрын
05 to 10 is this engine & setup
@frayjc 6 жыл бұрын
First time engine removal , just wanted to know when pulling out the engine do I worry about the torque converter being attached or do I take it off prior to pulling the motor ??
@princemario2299 3 жыл бұрын
Best is when you remove the plate under the car take out the four nuts that is going through the flywheel and the motor coms out easier
@andrespalomarez3794 2 жыл бұрын
Im doing an engine swap on the same motor now. I pulled out the engine with the torque converter attached(tough!). After speaking with a master mechanic he explain that in the end i would not have a choice since the engine I was removing was locked. Advice was free too!
@generatemediallc9181 6 жыл бұрын
Good work documenting your engine removal. I know its time consuming but rewarding at the end.
@kurioca195 6 жыл бұрын
Generate Media LLC Thank you for the support. It's been quite a while since I've made any repair videos.
@princeiQ1 6 жыл бұрын
im going for this, but changing the engine, so why not unbolt the torque converter before remove the engine its more easy, i did it with dodge neon, but dont know about charger
@torquewrenchjeff2622 6 жыл бұрын
is it possible to bolt converter on wrong? is there an offset in the torque converter bolts so not to allow it to be bolted on wrong? that crankshaft sensor on the trans is why im asking.
@santosford5714 6 жыл бұрын
jeff wrench anything is possible
@alanwilsonowens 7 жыл бұрын
You mentioned that you only had 100 miles on the transmission since installing it with low fluid levels, that should be ok, minimal friction damage. Plus you can always put slick50 in it!!! Nice video Chris, keep it up.
@imnophd 7 жыл бұрын
This video was incredibly helpful! Thanks for making it.
@kurioca195 7 жыл бұрын
imnophd your welcome thanks for watching.
@yaakovisrael8078 7 жыл бұрын
Can a 3.5L be swap into a 5.7
@covingtonpaul94 7 жыл бұрын
of course lots of work better off to have the NAG1 transmission vs the 4 speed. remember those early year 5.7l engines have a valve seat defect.
@covingtonpaul94 7 жыл бұрын
only way to correct is to remove all old seats and replace them with oversized seats.
@MoparGuy1625 7 жыл бұрын
Emil Roberts Why downgrade engine?
@legend4267 6 жыл бұрын
of course u can put a hemi it it's a dodge engine u just haft get different engine mounts