6.8 just do 7

I love the trial and error im surprised your filter housing came off in that manner was shaking my head up until it actually worked lol

Despite the code not erasing, that video was the best video angles and wiring I’ve ever seen.

that trans mount is always a pain, i replaced my mount and strapped the rear of the trans down ,,,,,,, my 97 TA if a wiring nightmare .... it seems to get a new issue as soon ans one is fixed LOL ...

Respect !! But sadly Gonna b Charlie Davison very soon

Thank you! My son and I just did ours in less than 30 minutes thanks to you.

Nice video

Might also want to check your harmonic balancer orientation as I recall they are weighted a certain way from the factory and the crank hub needs to be oriented correctly on the crank snout. Did also find a scenario in which the oil from a cheaper air filter kept coating the MAF sensor causing it to read wrong. Hope these help.

I work at Firestone and found this the other day on Mitchell... "Technical Service Bulletin Reference Number(s)02-06-05-004b Date of Issue: February 14 2006 Service Information General Motors Engineering, in an effort to determine the root cause of catalytic converter damage, has determined that aftermarket alarm systems incorrectly installed in vehicles have the potential to cause misfires codes and damage to the converter. These alarm systems use a circuit interrupt which utilizes the ignition circuit on the vehicles. These alarms systems utilize mechanical relays and normal vehicle movement can trigger these relays to engage and disengage the ignition circuit while the vehicle is in motion. These disruptions of the ignition circuit, which occur in milliseconds, may cause more fuel to be commanded. Over time, this dumping of fuel on and off again can cause misfire codes and ultimately damage the converter assembly............." May be applicable, may not.

Ong they delayed my package 5 times and the delivery guy doing a loop in the same place instead of fly out to my country

Will this work on a 1993 firebird

First 3 minutes is you checking the tire pressure, then when you get to the actual reset procedure, it's just you mumbling. Really? If you're gonna put out a tutorial on something, make it concise, educated and at least somewhat audible...

Never done anything like this before . I've talked it so far I'm getting ready tom to take off that last bolt for the air pump . What did u fine was wrong with your car?

Fuck that air pump has been a pain in my butt I was looking for a video that had 1 on there I just got that middle bolt off ahah thought the same thing this should do it nope that 1 behind the spark plug .. what a engine

2014Serento sX , alt. Went dead/ all dash lights came on/ engine died 😢!! Kia dealer wants $1100.00 to repair. I removed alt.with some difficulty,took it to alt/starter shop. 2days later got my rebuilt alt. for 185.00$ installed with some difficulty. Your video is to the point,thanks I will point out after starting and idling charge was only 11.5 vdc , but once I reved the engine over 2000rpm I got 14.5vdc ,, the ECU must control the charging rate by time running and or rpm 😅

Great tutorial, covered a lot of ground, much appreciated.

Good video thanks

Question.....did itnfix your concerns? Im having issues starting now.

Please do a video on power windows!🙏

thaNK YOU SO MUCH!!! YOU ARE THE ONLY ONE i FOUND THAT RESOLVE MY ISSUE !!!

Just a little finesse let it sit for a while don't force anything you don't want to break the handle how come those had the same problem

Check fuel pressure sensor?

I autocross an Integra Type-R and one of these came up for sale. We're thinking about getting it now I want it more for autocross🤣🔥

Didn't like the fact that the video wasn't more under the hood and we could actually watch the job being done step by step instead of saying more of what was being done. Camera man was not close to the details which helped it come off as a lazy demonstration more of hurrying up to get it done less of look at what I'm doing so it helps you more to learn.

Hello friendo, im have a trans am 1994 automatic , and my code obd1 is a 18 what problem is??

I think my navara the torque settings for the wheel bearing were 40 lbft. I cranked them snug then a half turn each.

What is the buzzing noise or compressor noise when you turned the key back on after the fix

What does the orange wire do , what is the orange white wire used for ?

Thanks my 2006 blower motor is out this helped immensely.

THANK YOU SIR!!!!!!

Had 6 firebird's....My least favorite engine is the LT1....can't beat a 400.

What did you use to reseal it?

Brilliant walk through of how to do this. Unravels the puzzle very well and would be nigh on impossible without this information. Awesome work.

I just installed the same headlights. Luv them. Same Nissan. New paint job as well. However I have a problem. The turn signals only work normally when the headlights are not on. When the headlights are on, the turn signals front (& rear) start blinking very fast and the L.E.D does not complete the entire loop. Fun install, but trying to trouble shoot that issue.

Awesome Biff!

Hey biff love the Chanel, but I have A 94 formula with the 5.7 lt1 and I have the same identical codes all 8 what I was wondering is did you find the problem that was causing the problem. Thanks Ron

This video was a quick fix to solve my problem in about 15 minutes thanks alot!

I cannot thank you enough! I also own a 1994 and yes it is disheartening that noone reproduces these taillights. I need a set desperately bad, BUT, fact is all of them do the same thing, so why spend $650 on them when your lucky to get a good year out of them. I most certainly will be doing this! Thank you so much for taking the time to do this video and help all of us out so very much!

What is the tightening torque for the bolts of the pan itself. I have changed the new pan/gasket, but it's leaking. Thanks.

Change 2 see if it's Sparking

Yellow top it the way to go

Ok, so I followed this tutorial and it was very helpful cutting through the mystery of just digging into the job outright.. Direct labor time (Waiting on the wife to get the new alternator and her battery charged) this removal to full installation was about 2.45.. The wife said she was finding things that weren’t working right and quite a while started working again. Like the sports mode in the steering gotmuch much better and even her headlights which she was getting new bulbs all the time because they didn’t seem bright enough finally got a lot brighter. Never knew when a car depends this much on electronics how much that alternative plays a role into it. Great video…

So all in all, roughly how long did this job take to do? From start to finish that is?

Good video

Your a machine, took the pulley with no special tool. Nice dude i rewinded twice

Thank so so much teacher 👌🏽

How hard was it for the middle seat belt I’m stuck on that part right now any advice ?

Perfect thank you for the help

Whats your review on them so far? I really like the look but cant find many reviews on them

1992 TO 1996 CAPRICE ~~ ALSO SAME OPTISPARK