Matthew Liphart

Пікірлер

@janetadams7080 13 күн бұрын

What are the torque specs when installing/reinstalling the throttle body?

@mliphart 13 күн бұрын

The torque spec is 105 INCH pounds (or 8 ft pounds).

@dukevandine5080 14 күн бұрын

Thanks, toothpicks... great idea

@mliphart 14 күн бұрын

Yes, works great - thanks for the comment.

@JohnParker-tt9bu 16 күн бұрын

13 mm and 1/2 inch are so close it’s not a secret 8mm & 5/16 old school shit

@mliphart 16 күн бұрын

It is - to those who use it. Thanks for the comment.

@daveallmon6937 21 күн бұрын

You don't have your mass air flow sensor plugged in lol

@terrywilliams6820 28 күн бұрын

Came out a little bit tough!!! Ya right.. this was the hardest alternator change I have ever done. Give me a GM over this any day'...

@mliphart 28 күн бұрын

I hear you - but, I have done alternators that are much harder than this one - that's where the comment came from. Thanks for watching, and thanks for the comments.

@MrSergio608 Ай бұрын

Thanks very much. There is 0 information for a 2015 Challenger expansion valve on the WWW. This was exactly same as mine.

@mliphart Ай бұрын

Thanks for the comments.

@christinamunoz2641 Ай бұрын

Do I need to disconnect the battery before I start? I want to finally tackle this project for my wheelchair van ♿️

@mliphart Ай бұрын

I would definitely disconnect the battery before doing this.

@sanianata Ай бұрын

Good afternoon. Why did you change this part? I have a high pressure in the return line of the air conditioner. There should be low pressure in that line and I have high pressure there. So I need to change this part too? Thank you.

@mliphart Ай бұрын

Possibly. The expansion valve is the part that creates the "high pressure" side - so, it is possible. I changed mine because I wasn't getting cold enough air. I ended up replacing the back expansion valve, too.

@sanianata Ай бұрын

@@mliphart do you have the front valve number?

@mliphart Ай бұрын

@@sanianata AutoZone number is 39321

@HonestOK2930 Ай бұрын

I followed the steps and made sure the new cable was perfectly installed. Reinstalled the console and no change. Monitor is still blank, but able to access menu as before. Could it be a cable behind the dashboard?

@mliphart Ай бұрын

Not sure, possibly. Does it play on the "in dash" unit?

@HonestOK2930 Ай бұрын

@@mliphart Yes

@geno2001h Ай бұрын

Thank you for your help

@mliphart Ай бұрын

My pleasure.

@RayCampbell-dt1nf Ай бұрын

I did the throttle body cleaning today. Hopefully it helps some. It was just as dirty as yours. Thanks for the video. It made the job very simple.

@mliphart Ай бұрын

My pleasure.

@makafela788 18 күн бұрын

How is the performance since you last fixed it?

@mliphart 18 күн бұрын

@@makafela788 it seemed to be a bit more responsive - but, ultimately didn't fix my problem. My problem ended up being a defective computer.

@RayCampbell-dt1nf Ай бұрын

Ok. I replaced the computer on hers about a year ago. It ran fine for a while and then started acting up again. It stalls occasionally, idles rough, stumbles while going down the road. Occasionally trouble cranking.

@RayCampbell-dt1nf Ай бұрын

I'm curious if cleaning the throttle body fixed the stalling issue. I'm having trouble with my wife's Hemi.

@mliphart Ай бұрын

Cleaning the throttle body helped - but, in my case it was a deeper issue. It ended up needing a new computer. Bit, always start with the simplest possible solution.

@clarenceyoung4701 Ай бұрын

Would an alternator throw U1110 code and turn on your ABS and TCS lights. My volatge was at 10 too.

@mliphart Ай бұрын

Not that I know of. My understanding of that code has to do with a communication error.

@odinsdottir5308 Ай бұрын

Thank you, was worried the fuse bank had to come out.

@mliphart Ай бұрын

Thanks for the comments.

@tommydanger4461 Ай бұрын

Wish you showed how to get belt off🫠

@mliphart Ай бұрын

I thought I did that, but as I watched it back - you are right - I apologize for leaving that out.

@jaaredhildebrant4129 2 ай бұрын

So did it fix the high idle.

@ghostsniper2099 2 ай бұрын

Very poorly done. Didn't you even view the vid before you uploaded it? Thumbs down.

@mliphart 2 ай бұрын

Not sure what you didn't like - but, ok. Thanks for comment.

@100percentraw7 4 ай бұрын

If your here you didnt give up on your chrysler

@anthonyallen921 4 ай бұрын

Nice. Thank you.

@mliphart 4 ай бұрын

Thank you for the comments

@johnhestle8304 4 ай бұрын

I have 2008 chrysler 300c keeps killing batteries, wont go over 30 miles per hour with new battery.

@mliphart 4 ай бұрын

Have you had the Alternator checked? It should be putting out around 14 volts - no less than 13 volts. Have that checked, if you haven't already.

@KrissyChacon 4 ай бұрын

I appreciate this video so much. When I saw where my alternator was I almost panicked at the idea of needing to take it to a mechanic. You are about to save me so much money!

@mliphart 4 ай бұрын

Thanks for the comments. I'm glad it helped. Please subscribe, if you haven't.

@enc4life1010 4 ай бұрын

Is it better to buy a new or refurbished?

@mliphart 4 ай бұрын

I have bought Remanufactured alternator all my life, and have had very few issues.

@jaxcell 5 ай бұрын

Cool, Thanks. Not a MOPAR Guy and needed some direction.

@mliphart 5 ай бұрын

My pleasure, thanks for the comment.

@johnnagle8294 5 ай бұрын

Very helpful thank you

@rbos7525 5 ай бұрын

Thank you for taking the time to put this video together. Super helpful and I was able to fix the issue on my 2016 T&C!

@mliphart 5 ай бұрын

Thank you for the comments. Please subscribe, if you haven't yet. Thanks.

@pizzarat7825 5 ай бұрын

Very helpful, thank you!

@mliphart 5 ай бұрын

Thanks for the comment. Please Subscribe, if you haven't.

@zandermccrady8678 5 ай бұрын

Do you have any idea on how to take the dash out because I am looking for a wire harness because my code reader doesn’t work and other stuff like my key doesn’t turn the ignition off my passenger door open it turned it turns the truck off

@mliphart 5 ай бұрын

I have not had to take the dash out - so I can't answer that question. I do know that many vehicles have bolts coming through the firewall that holds the dash in place.

@haleyokoro1487 6 ай бұрын

Is there a way to make sure you get the correct ribbon cable without taking the whole top panel out? I keep seeing to make sure you have the correct part number, but haven’t been able to verify an easy way to know what cable to order as there are two different ones.

@b..1kevinmessner606 6 ай бұрын

Thanks for this video, very helpful. I'm not sure if I have the wrong bulb or not but I have the H-13 bulbs. My issue is the headlights are very dim, almost like they're (DRL)'s daytime running lights. When I hit my high beams then they seem like normal headlights... No one flashes their high beams at me so my question is, what was the headlight bulb # you used? My soul does not have (DRL)'s so I definitely think it's a bulb issue...🤷🏼‍♂️

@mliphart 6 ай бұрын

Yes, it was a H-13 bulb. I am not sure why your Kia would do that - it is a bit odd. But, if it is not causing problems while driving - you have to decide if it is worth spending the time and/or money to make it right.

@b..1kevinmessner606 6 ай бұрын

@@mliphart agreed, I just got my Kia a little over a month ago. I actually changed the ballasts that hold the bulbs too due to them getting real hot and almost melting from what they looked like. Eventually I want to go with the LED headlights so that may be the next step. Thanks for the info though, I really appreciate it.

@mliphart 6 ай бұрын

@@b..1kevinmessner606 thanks for the comments.

@Turtle_army_ 6 ай бұрын

Where do you get the replacement strips?

@mliphart 6 ай бұрын

I got them from Amazon. They are quite plentiful on Amazon.

@user-jn8vx7gu3j 6 ай бұрын

The bleeder screw on the front of mine is bone dry I hear a squeal when I cold start I’m guessing water pump being that it’s dry but what could be causing the pump to not get coolant in that area because the hose and rad have fluid in them but nothing in the front of the water pump housing, I’ve been having issues with it getting hot the. Cooling down getting hot then cooling Down originally had a leak and used k seal fixed the leak I think but then the overheating issues started, hasn’t overheated but it gets hotter than it’s supposed to I think I’ve seen it get up to as high as 242 then shoot back down to 195-197

@mliphart 6 ай бұрын

These engines are very finicky. They get air trapped in them and will overheat until it is out. I start with plenty of water and Anti-Freeze, and with the reservoir cap off - start the car and let it idle - with the heater on high. At some point, the car will suck the water down - be prepared to refill it as it goes down - DON'T WAIT UNTIL IT ADDS MORE AIR INTO THE SYSTEM. I let this process go for about 45 minutes. It will bubble out both air and water - but keep it as full as you can. As long as you don't let air back into the system, you will be ok. I just had to do this to my wife's car. It got low enough on coolant that it got air into the system. It is an idiosyncrasy of some vehicles - this being one of them.

@user-jn8vx7gu3j 6 ай бұрын

@@mliphart ended up putting a new water pump in it and then followed this process and it worked, thanks a bunch!!

@mliphart 6 ай бұрын

@@user-jn8vx7gu3j my pleasure.

@littlemotor414 7 ай бұрын

Ha! And there it is!! I commented just a few minutes ago on a previous video I just saw, and decided to dive into your channel to see if you had uploaded the penetrating oil. Brings back memories!

@littlemotor414 7 ай бұрын

Ive seen this demo before, and I’ve done it. Back in about 2011-2012 or so… Those bits are legit. I bought the set up to 1/2”, and it had a decent three drawer box. I never burned one up. And most of them from 1/16” or 1/8” (can’t remember how small they went) up to I wanna say around 3/8” had multiples in case you’re an idiot, and did manage to somehow break, or burn one up… Now you mentioned in the beginning of the video that you were going to show off the penetrating oil as well I believe, but we didn’t get to see it lol… I can attest to that as well if it’s the same formulation that I used… It was KM penetrating oil is all I remember, and it smelled like freaking CAKE BATTER. I swear on my life. I’ve still to this day never used better, and I’m in industrial maintenance… Blaster, Kroil, Knocker Loose, WD, Amsoil, DuPont; NOTHING came even remotely close to that cake batter. Thanks for posting buddy!

@mliphart 7 ай бұрын

Thank you for the comments.

@littlemotor414 7 ай бұрын

@@mliphartabsolutely! Could I get a price on the 3drawer box set of the super primalloy bits buddy? Thank you!

@mliphart 7 ай бұрын

Right now, it is going for $558.86. I will double check if there are any promotions for them now, and get back to you.

@lindaconner3236 7 ай бұрын

I love this recipe. Have cooked it many times. 😊 Ty !!! 💛

@mliphart 7 ай бұрын

Thanks for the comments.

@kingbam 7 ай бұрын

That one in the driver side is a son of gun

@mliphart 7 ай бұрын

Yes, lol - especially if you have big hands.

@Relevantminded 7 ай бұрын

118 ft pnds for the axle nut that way you don't risk over tightening and causing problems with the wheel bearing assembly.

@mliphart 7 ай бұрын

Thanks. I knew there was a torque spec - but due to how often I have done it - I do it by feel. Thanks for the info.

@Relevantminded 7 ай бұрын

@mliphart it took me abit to find it, one guy on KZbin was saying 180ft pnds but later corrected it in his comments lol

@BanditRider86 7 ай бұрын

Thank you so much fixed my wife's van 👍

@mliphart 7 ай бұрын

Glad to hear it. Thank you for the comments.

@michaelsteinbach 7 ай бұрын

Probably would have used a headlight restore kit while they were out of the car. I need to restore my wife's (they've gotten milky like yours) but I think I'll just mask off and rework them in place.

@kianapena7454 7 ай бұрын

Heaven sent 🙏🏾

@503jmn 8 ай бұрын

For those that have cars that stall after a fill and then the car turn back on later...there's a free gas tank replacement the dealers won't tell you about. I pressed them and they changed my 2006 300C's gas tank for free for this issue. Here's a link to another owner who has the official letter for getting this repaired. kzbin.info/www/bejne/pnXCq32bhL-rm9k

@mliphart 8 ай бұрын

Thanks for the information.

@LuisChan-cr7vl 8 ай бұрын

A have a 1999 too thank you I will clean it tomorrow

@diegomorales1717 8 ай бұрын

My truck is manual too I can find the correct piece , so how cancel the ítems for the transmission automatic you can tell me please !

@mliphart 8 ай бұрын

I don't understand the question...

@georgiemonti 7 ай бұрын

I think I get what he's asking. I have also a manual transmission and can only find radiators for the automatic transmission. The question is, do you have to do anything to the cooling lines or are they plugged from factory?. I think that's his question... thanks in advance and great video

@mliphart 7 ай бұрын

@@georgiemonti no, there is nothing that you have to do. The inlets for the transmission lines go to entirely different compartments within the radiator - so, you don't have to do anything with them.

@georgiemonti 7 ай бұрын

Awesome. Thanks for the information, was holding back in buying the radiator because of that. You gained a subscriber buddy...

@mliphart 7 ай бұрын

@@georgiemonti thanks, I appreciate that.

@DoronBond 9 ай бұрын

Got the same P0016 code. Just bought the sensor. If it’s that simple 10mm socket shoot I can do it myself. Just need to go borrow the tool to do it. Hopefully that will help remedy the issue which was the gears shifting from time to time between 40-60mph..

@mliphart 9 ай бұрын

Not sure if that will affect the shifting - be interesting to see. Make sure to replace the Camshaft and the Crankshaft Sensors. The Hemi is funny about that.

@DoronBond 9 ай бұрын

@@mliphart I actually don’t have the hemi..the code only showed the camshaft..I only purchased the camshaft which I can change on my own..but I’ll let let know if that changes the shifting

@darrensimms4742 9 ай бұрын

Thank you so much for making this video. This is exactly what I needed to do in order to get the DVD player to work in my 2016 Town and Country. My four kiddos thank you the most as now they have a DVD player right before our family vacation.

@mliphart 9 ай бұрын

Thanks for the comments. That's why I do these videos.

@Sandman35739 9 ай бұрын

Great video! I broke the screw hole on the carburetor so ended up ordering a new one from Amazon, and since it came with a new air filter and spark plug I went ahead and replaced them also. Bad news: the mower still didn't start. Did you ever solve the Automatic Choke issue? I checked it out and it seemed to be connected OK but I don't know what else could be wrong with the mower.

@mliphart 9 ай бұрын

I have not gotten it completely solved - it's a pain. I'm working on somehow rigging up a manual choke.

@kevinmanning7174 9 ай бұрын

Thank you for sharing

@mliphart 9 ай бұрын

My pleasure

@joshtaylor4249 9 ай бұрын

Just got my first can from my sales rep Chris Matthew's. (Great Guy) I'm super excited to use this product, especially after seeing the demo. I have several Kimball Midwest aerosol products, they have all performed far beyond my expectations. Going to purchase the cobalt drill index and die grinders soon.

@mliphart 9 ай бұрын

Nice. Kimball Midwest definitely has some quality products. Thanks for the feedback.

@joshtaylor4249 9 ай бұрын

@@mliphart It was my pleasure.

@brendagomez8499 9 ай бұрын

Thank you

@mliphart 9 ай бұрын

My pleasure. Thanks for the comment.

@anthonyportugal9013 9 ай бұрын

How much coolant it takes to fill it up after replacing pump?

@mliphart 9 ай бұрын

The entire system takes about 14 quarts - but, the system isn't completely empty. I typically will put 1 gallon of the "concentrated" Anti-freeze, and the rest water. Depending on where you live, and how cold it gets - you want about a 50/50 mix.

Ең жақсы KZbin

Пікірлер