Thank god your video is here . 🙌🏼

little tarp on ground tip rotate swing around a bit get a second to help pull out 4 points lift and tip into wheel barrow

That dado you cut is the literal definition of a learning curve. My brain insists that one should actually do the opposite. Instead of actually undoing the plywood by cutting a dado on a sheet of ply that thick, I suppose one could stack and laminate two sheets of ply half the thickness and stagger them. Then rip the overhang and glue that over to the staggered side and leaving a gap that will have the excactly same function as this dado. The time spent for the labour will be only valuable if you have no access to ply half the thickness. Still this was a great show of determination by you! 💪 It is very important to experiment and feel the actual value of your time by using it ineffectively for a short period of time while infusing yourself with the knowledge to use time more wisely for the long term. Cool to see your experiment and I enjoyed your commentary and reflection 👌

Thanks for your video, first of all. I don’t think you actually had test result. Unfortunately, you had several marital issues with your test and didn’t use similar testing methods either First of all you need to use a drop of the Super Glue and should not have used the brush applicator to place the glue. The test was rendered immediately skewed and invalid when you did this. As the perimeters are apples and oranges. Also you should have need clean metal for the test. If metal is not cleaned then any surface contaminations. Case in point you look at your test samples. The glue on the board for both cans had the label material left on them. This means it was labeling on the case that failed and not the bond between the can the board. Good demonstration though.

I don’t get the temperatures, are in Fahrenheit?

Thank you. There is no way I would have been able to figure this out with just the instructions.

Thank you so much. I realized by step 3 in the included instructions that It was going to a difficult one. Your step by step was perfect. Very clear and easy. I got it done quickly :)

I tried to build my first one according to B&D's instructions. That got me nowhere. Then, I found you, and did it the way you showed, noticing that you said you were going in their order, for the sake of keeping it less confusing. It worked! W00t! Then, I started building the wnd one, and did it a little out of their order, attaching the first board, before worrying about the cranks. That held the auger(?) piece in place, instead of leaving it flopping all over, while I fought to get the pins in. Easiest way, yet! After finding your video, the first one went together in about 20 minutes (instead of throwing it out, after an hour of much cussing!). Modifying to my way, the second went together in less than 10 minutes. I'm noting you didn't say the way you showed us was your favorite way - just that you did it that way to help avoid confusion. Well done, sir! Thank you!

Wat to close with the video. can't see what's happening. Size of fence. Etc

Oh! TYSM!

Thanks exactly what I needed to know know

Bringing all the Karens out. 😂

sadly, your camera zoom is too tight most of the time. Need more visual information. Your dialogue is great, wonderful talk through. I bought the exact parts you are talking about here from Lowe’s, so that helped me. Maybe the video rendered in a cut down frame. Not sure. Thx thx. Good over all.

Excellent! Thank you!

The plastic white thing doesn’t fit into my trimmer, it’s too big

If you use Timer mode, manual says that you have to reset this timer each time, meaning it only sets 1 future timer up to turn on, and for example if you select 8 hours , it will not continually turn it back on and off every 8 hours? Odd. And with the option to CHOOSE your humidity level, if you choose 50% say, it will turn itself on and off by itself throughout the day to maintain that 50%? Continuous mode does not let you set a desired level and runs 24/7?

If you use Timer mode, manual says that you have to reset this timer each time, meaning it only sets 1 timer up, and for example if you select 8 hours , it will not continually turn it back on and off every 8 hours? Odd. And with the option to CHOOSE your humidity level, if you choose 50% say, it will turn itself on and off by itself throughout the day to maintain that 50%? Continuous mode does not let you set a desired level and runs 24/7?

I rarely see Gold in my area. Now I want to try it so I'll look for it.

Good guide! Thanks

Thank you

2 fence posts and load of u nails will work for height

A company of crooks. We bought two devices, one from Amazon USA and the other from Amazon Germany. Both arrived not working. Dead. A lot of money. I contacted the company, provided the representative with all the documents and photographs she required and they refused to replace the broken devices. I will note that formally the devices have a warranty of 3 years. But in practice there is no guarantee of one day. Don't believe the ads!

I am in the process of building an outer space cosmic cat playroom - coffee movie room . So far I have a planetary wall that glows in the dark and gives the feeling of moving thru space but now am building the control panel wall from styrofoam.. This video answered my questions. I'm glad I looked it up!

Like others, this was the exact content I was looking for, as I am looking for new graters. Thank you for producing it! Super helpful

Thank you for making this video. The instructions were very confusing, the instructions also had some things mislabeled and drawn differently than the actual parts making the parts hard to identify

Thanks, this video really helped. Only issue I'm having is when I close the right door the bottom half of the door is getting caught on the left door, I have to give it a kick to close. Any ideas?

Hi - I have a similar vac from Panasonic, but the grooves for fitting the bag are not deep enough and the bag slipped off on first use, tipped into the canister, and mucked up the filter. Could you please suggest a solution? many thx. Its one of those small reusable cloth bags open on one side and secured by a plastic slider

You are right the instructions were poor and labeled as though they had labeled parts, which they had not. Not an easy put together as the screw holes were next to other features that made it difficult to put them on and tighten them. Thanks for the video

Would be great if they made pyrex or glass ones!

Thank you for this! Was unsure whether it should be flexible in the seating position or not, and this was the only video I found it in! :)

your a legend, they need this video on their site not the shitty one they use. i got it right away with this tutorial

Thanks for doing this 😊

mine is old and doesn't have a font button.

Mine is set to large but still prints small. What am I doing wrong? Is there a way to factory reset it completely? It used to print large but now it won’t.

I haven’t looked but how about a Scrub Daddy/Mommy battery polisher? Love this line of cleaning products 👍🏼

Worst instructional video makes me crazy never zooms out to get a better view of the overall spring.(*&)^

Hi, where can I get the 30 L one? Thanks

Great vid

Can do continuous label with frames each one or do need do it one at a time?

i love you🥳

Thanks for the info! BIG help.....

Cheers bro I thought my keyboard was useless after the batteries died 🙏🏼

Thank You! Very helpful

Nice to see all angles of the case itself, but I wish you would have included some clips of the actual USE of the keyboard and trackpad.

a shop vac makes this a piece of cake-- way quicker than the included pump-- suction keeps it on without needing to screw the nozzle on and really cool to watch it shrinking

Thank you!

Ĥow to repair the on off swtch

How to change the lithium ion battery

Just bought some of the king size markers. They are all plastic now, really sucks.

Get me vacuum out.