How To Build A Black and Decker Workmate 225 Workbench (WM225 Manual)

[@candicemcmath4521]

THANK YOU! I just got one of these for Christmas and their instructions made NO SENSE. you saved me hours!

[@CaptainCharleston]

You've done a great service for your fellow humanity!

[@robertmicheletti3945]

Great video, not complicated the way you explained the process, thanks so much, saved a lot of swear words!

[@brycecarter722]

Great video. Unpacked to fully installed in under 30 minutes. The tip to use pliers instead of a hammer for that friction rod was very good. 👍

[@johnlang2293]

DUDE !! Thank you, I watched your video twice. The included directions are totally wrong, and you need a microscope to view the images in it. Your video saved me from losing my marbles. THANK YOU !!

[@johnlang2293]

1 bolt for each end of each plank, seeing the 2 holes I was looking to put 2 bolts into each end of each plank. That's wrong. B&D should include your video with their product. You are AWESOME !

[@HelpAtMyHome]

Glad to hear this helped.

[@Murikuki]

there is no way we would have been able to put this table together without your video..thanks!! 😊😊

[@natpetasen3855]

Thank you from Thailand😊😊😊

[@tc4680]

Thanks so much for the video! I would never have figured out the instructions.

[@MrAnderson1966]

Thank you. There is no way I would have been able to figure this out with just the instructions.

[@katywebb5031]

You just saved us a ton of time. Thank you!!

[@narutosasuke8580]

Thank you for making this video. The instructions were very confusing, the instructions also had some things mislabeled and drawn differently than the actual parts making the parts hard to identify

[@jonathanspencer9959]

Most helpful. Thank you. I had got quite lost with the printed instructions.

[@jameswoods6900]

Well I finally got the delivery and put it together. I had a hard time lining up the pins for the handle and tried to use a hammer and that seemed impossible, so I used a channel lock with a pad at the bottom to avoid scratching and that worked. The pins are now the same on both sides.

[@larryrogalski4067]

Great job great video!! Thank you so much!

[@HelpAtMyHome]

Thanks!

[@jameswoods6900]

NOTE: the back piece can be put together without being on the bench! Very Good Job! Now do a video on how to hang on wall!

[@SPX9987]

Thank you 🙏🏻🙏🏻

[@amandachan696]

Awesome video man! Ty!

[@HelpAtMyHome]

Enjoy the bench!

[@lihua8838]

Thank you!

[@AdamRinehart]

Thank you! As you said, starting at step 19, the instructions are worthless.

[@Jordan-ql6tm]

Black n Decker owes you some money. Those instructions were absolute trash 😂

[@Saksitsaelow]

Yep absolutely

[@jeffdickemper5214]

I camnot thank you enough for clearing up this assembly. The directions included are some of the worst ive ever dealt with.

[@allengfreeman]

The included instructions are total garbage. How does B&D not redo the instruction manual? Crazy. Thanks HAMH.

[@onesassymama]

I tried to build my first one according to B&D's instructions. That got me nowhere. Then, I found you, and did it the way you showed, noticing that you said you were going in their order, for the sake of keeping it less confusing. It worked! W00t! Then, I started building the wnd one, and did it a little out of their order, attaching the first board, before worrying about the cranks. That held the auger(?) piece in place, instead of leaving it flopping all over, while I fought to get the pins in. Easiest way, yet! After finding your video, the first one went together in about 20 minutes (instead of throwing it out, after an hour of much cussing!). Modifying to my way, the second went together in less than 10 minutes. I'm noting you didn't say the way you showed us was your favorite way - just that you did it that way to help avoid confusion. Well done, sir! Thank you!

[@HelpAtMyHome]

Glad you got through it. 10 min is fantastic!

[@onesassymama]

Eh - could have been 15, lol. But, it FELT like 5, after the frustration of trying to do it, with just the instructions!