@@HivesToHome thanks! Me too

On the forklift? It’s called a clamp. I have a video on it. We did not make it from scratch, but we did modify it.

We ship them on the 11th day. They start hatching during shipping. We always ship next day.

@@BeeInnovative 👍👍👍👍 thank you

Great northern trailers. In Washington. You’ll have to call them. It’s called the Beekeeper trailer. Around $8k

The lamp was an Amazon purchase, it doesn't have any labels on it, the lamp holder is by a company called Mediflex

Thanks! I'll check it out and see what I can find.

Yes we do

Are plans available?

@@bettydaltonnewbold2019 are you asking for the technical blueprints of the bee boxes?

Maybe I was not clear there is grease in the boot. Usually we greased them every couple of days. How we don't have to because the boot keeps them clean and lubed.

Поставь перевод и поставь малую скорость и ответ четкий. По сути это не существенно, главное личинка в питательной среде.

@@BeeOleg1890 уже сделал, только вот интересно, после 2 на третий день кормления личинки состав молочка меняется, .... ладно будем сами пробовать, если секрет не кто не расскажет, спасибо!

@@yasenkovskaya_paseka не существенно, убираете двух- трех дневных личинок и выбираете маточное молочко и добавляете в мисочки, или перед запечаткой и старше, но тогда наро разбавлять водой. Главное личинка для прививки должна быть не в стадии линьки, тоесть блестящая.

@@BeeOleg1890 Спасибо, вот теперь всё ясно! Всего хорошего и всех-всех-всех благ!!!

Glad it was helpful!

Thank you! Means a lot to us

@@BeeInnovative You are very welcome! :)

Shop Valves Online MA052 1/2" Mini Float Valve, Adjust

You need to take off the front cover, the high psi pump and the beck of the governor, I believe there is a retaining clip.

We use two styles. One is adjustable and the other is not. M052 PVC Mini Float Valve

You are welcome

@Ets Bees it depends on the parts. Most are common parts so I just google them. Or the local auto parts store, rock auto is also an option. Some parts I get from the A & O direct. Yes we run two swingers and one hummerbee turbo

@@BeeInnovative I thought A&O went under

@@ETsBees they are now hummerbee. Same company, different name.

That is true. The question is, is it worth the risk?

@@BeeInnovative ABSOLUTLY! Just make sure you workers hook up the trailer correctly.... I will have to make a video of cutting out a part of the bed on a pickup to weld in a new piece 😁

This a governor, it regulates the throttle for the engine. Oil pressure is different. You have the oil pump which creates flow only. Then you have a restrictor usually a spring with a plunger that creates resistance in the line, which creates back pressure.

Yes there is a queen in the bottom box. The only queen less hive we run are the queen banks. Everything else have queens

Isuzu does offer a 4x4 option. Just not in the US.

Thank you!

Thank you! We are located in California. What is your question

No. The Isuzu is 19.5 K lb max The trailer and and forklift are 6-7k You are right at the limit! I’m not saying if the bees are a little bit heavier than you expect, you will go away over quickly, but that is the absolute maximum you can have. Ultimately, I would recommend just getting a class A, but good luck getting a class a driver. That will also work with 🐝

Are you asking about the trailer? Or the HummerBee?

@@BeeInnovative show us moving the trailer full of bees with the hummerbee

@@ETsBees 🤔 okay, we usually use the truck for that but will do it just for you!

@@BeeInnovative I want to see that too. So it for me too😆😆

😂 this is true!

As you should! If there is enough interest I could make a video on how to make them.

@@BeeInnovative i think it is really obvious how they are made, but well I‘m quite into building stuff myself (last project was a bee crane, that now need a paint job done to finish). But for other people that aren’t as deep into that, it could help a lot. But one question, what type of material did you use for the sunscreen? I now thought about using silage netting ä, since it is quite stable, UV stable and at hand. Else maybe just search for shade netting at the agricultural store….? Also allready getting all the material for the feeding system. Will alter it a little, instead of an ibc tote and pump, i will be using a 1000 L steel pressure Tank and just put a 12 V air compressor on it, or maybe just fill it up to 600-700 L and pressurize it to 8 bars once.

@@kaistumer198 steel tank will work also, I just don't like pressure tanks, they can always fail. The sun shade is a 90% green shade from tarp outlet. Send me some photos when you have it working.

@@BeeInnovative Sure I will do so.

I have not use this product for more than one year so far. However the components they use are proven and automotive and racing communities for decades now. They are least likely to fail. But in case they do I have a back up ready to go. The most problematic parts in wiring are usually the connectors, that is unless you break through the wiring.

Absolutely! 😆

Thanks