The table is not installed correctly Extension could be on the side
@roberttravalent77823 ай бұрын
Thank you for the awesome video. I noticed the Ryobi BT3100 table saw. Just wanted to know how you like it. Thank you again.
@tskipwadoo34474 ай бұрын
Wen is Chinese too !
@user-fx6tk1jd5w7 ай бұрын
Ti DON'T look like a cr 5:28
@956Eltoro9567 ай бұрын
Can you use this to remove blown insulation???
@JjClark-wz7eh5 ай бұрын
Probably not, I have one and it seems like it would get clogged up quickly.
@madlion84357 ай бұрын
Good video. I needed this motivation to complete mine this weekend
@sirturd49667 ай бұрын
This guy is rediculous
@kencox1347 ай бұрын
Do you think it would be possible to wall mount bracket to wall and now that you have had it, does it work good. Thank you
@MrEzplay10 ай бұрын
100%
@wayneguy6043 Жыл бұрын
How , much was the shed? $4,000
@PaddyGDIY11 ай бұрын
Almost dead right!
@kdfleming2 Жыл бұрын
Thank you so much. This is exactly the type of ramp I want to build and for the same reason.
@SuperAudiowizard Жыл бұрын
Nice
@Golgafrinchamdent Жыл бұрын
Ouuuuch... lock the table down before pressing on the chuck
@wagerbaits Жыл бұрын
Could i use this collector for feathers
@olheghtt Жыл бұрын
With that system variable speed, wouldn't that wear the belt down on the sides pretty fast, it looked to me like all the traction is on the sides.
@PaddyGDIY Жыл бұрын
Yes, but the wear is minimal. I'm still running my original belt after three years or so.
@olheghtt Жыл бұрын
@@PaddyGDIY after posting my comment I thought about it a little longer. Pretty much all V belts have there traction from the sides so there's nothing unusual there as opposed.... I humbly withdrawal my original comment 😊
@asabovesotabelow Жыл бұрын
Did you ever replace the chuck or anything?
@paddyg1 Жыл бұрын
No I did not. Still running the stock chuck.
@asabovesotabelow Жыл бұрын
@@paddyg1 What sort of bit sizes/styles does the stock chuck take? I picked up this model as-is.. It has no chuck among a few other things but is in mint shape and seems to run well.. no smoke or smells coming from the motor area and I got a replacement drive belt already. I'm pondering ordering replacement chuck from Wen or maybe picking something up from one of the local big box hardware stores.
@rayray9777 Жыл бұрын
ok i had enough of watching you bend over in front of the camera. word of advise position your camera different . ass shots from men are not my thing...lol
@joshking9805 Жыл бұрын
Are you a fellow Tennessean?
@paddyg1 Жыл бұрын
Yes I am. I'm in the Kingsport area.
@mtibbe Жыл бұрын
Why wouldn’t you use your rubber mallet to tap in the chuck?
@scottfinlayson4754 Жыл бұрын
Pew pew pew matic
@paddyg1 Жыл бұрын
Lol!
@ncrown9773 Жыл бұрын
Thanks for making this video.
@tonyqrz Жыл бұрын
so can they run for long periods of time? planning to use on a cnc. 1 to 2 hrs straight
@paddyg1 Жыл бұрын
I have run it for a couple hours at a time with no problem.
@dwayneford1990 Жыл бұрын
Thanks for this video. I wonder how many people take the time to put silicone where it makes a difference. Saw a post the other day about a guy who lost some fingers by accidentally putting his hand near the impeller intake. You took off the guards and intentionally put your hand right on that intake. I know you know what you're doing but for God's sake be careful.
@mikethebike2456 Жыл бұрын
🏍️ When it's unplugged you can do anything. But your causionary tale is duly noted. 🔌
@dwayneford1990 Жыл бұрын
@@mikethebike2456 Thanks Mike. Just sayin', the machine was running when you put your hand over the intake. I'm happy still have all your fingers. Keep up the great videos.
@stoneycarter5546 Жыл бұрын
i bought one got it today wont even turn the motor wont run Junk dont bother
@katiemclean9089 Жыл бұрын
Great idea . Now I have to make one for myself C A McLean London Ontario Canada
@jasoncapps3516 Жыл бұрын
Most of us know you shouldnt put the lunber in direct contact with the ground also.
@markspeck3736 Жыл бұрын
Great video. I know what I’m going to be doing soon. Thanks for the tips.
@BigmoRivera2 жыл бұрын
Great Job Nicely Done 😉👍🏽🪚📐🔨✏️
@1mindtab2 жыл бұрын
Great job. I love the video. You make it look so easy
@carterscustomrods2 жыл бұрын
Another FYI .. The new versions at harbor freight have a new motor, and it's horrible. My motor housing was 135F after 4 minutes with nothing attached to it. I thought it was just a dud. Got it replaced this afternoon, and the replacement had the exact same issue. Hindsight, the manager kind of just nodded when I told him the issue. Like he already knew the problem. 😞 If you get one, you'll smell rubber burning after a couple minutes, then feel your motor housing to see if hot. If it is, I'd recommend getting a refund. I feel like HF could be doing a recall. It's a shame they likely went to lowest bidder on this after they sold out on the last one. I'll see if I can fish more info from manager tomorrow when I take this back for a refund. Now I guess I'll try a WEN 7.4 amp model... but I've never had much luck with WEN tools... but I can say the same about HF, so it couldn't be any worse lol.
@carterscustomrods2 жыл бұрын
Hope you're doing ok.
@carterscustomrods2 жыл бұрын
FYI, if you don't want to use silicone, or a permanent sealant for making it air-tight, just get some ⅜×⅜ weather stripping that has the peel and stick on one side. Then, just cut off what you need and put it to the area you'd normally put silicone. Another added benefit, is that it adds cushioning to prevent rattling. And if the day comes, where you need to take off a part to do a mid/upgrade, it'll be easy to take parts off. (But you'll likely want to replace the stripping every time you remove a component that it seals because it compresses and molds to the area, and it might not seal as well, as you replace the components.) Yeah... I just hate working with silicone caulk. Plus it doesn't interact well with poor quality metals if there is a scratch or chip in paint. So best of luck.
@andreardoin64942 жыл бұрын
Just what i need thanks for the video !!!
@MacDaddy882 жыл бұрын
Great job. Nice video. Waiting for my big HF to come in.
@josephromero15962 жыл бұрын
do u need to run cyclone if u take those screens off?? I have same one and debating on running cyclone or not
@David-pj5co2 жыл бұрын
I'm about to use one of these for My Move. I live near clearwater FL now the water is Great. I noticed he opened the door did You put a Lock on that i missed? How much stuff did You fit in it?. As far as customer service the first Rep i spoke to was Great although he said he would send Me his direct info so i Didn't need to deal with a bunch of different people, He never did. But Like You said every Rep i have spoken to was Great. Little Nervous but I appreciate your Video.
@xbubblehead Жыл бұрын
This was the pickup of the empty pod at the very end of the move. The driver was just checking to make sure the pod was empty.
@rudygeorgiamulesandcountry15942 жыл бұрын
Besides orienting the boards with the cup grain arching downward, it is highly beneficial to.fasten the 1× decking with 1/4" space between boards to provide drainage, ventilation and allow for expansion by moisture from precipitation. I would have added at least one extra stringer, spacing looks wide; although I don't know your dimensions. It looks wide at about 5 feet. Thirty inches is too wide for 750# load.
@patrickhayes30992 жыл бұрын
Paddy, May I ask if you were high when you recorded the intro? Love the video, Ima whip up new top for my unit! I'll be buying the right size bit and cutting those holes on a ganged stack in the drill press. Thanks for your time and effort to show us your shop!
@josephinehuerta64402 жыл бұрын
Wish there were closeups on his work. Half the time don’t know what he’s doing.
@mikekennedy31732 жыл бұрын
Thank you for the review, Did you purchase a different chuck? I am retired and have some hobby stuff going on. Just curious if the different chuck would aid in the run out? Thanks again
@josephlieberman30272 жыл бұрын
The first Modification which came to mind was The Casters,,
@rjwhite9072 жыл бұрын
Ain't much to look at!
@lucillewilson92022 жыл бұрын
Please wear safety glasses when cutting the wood 😊 thanks for the video and your tips,!
@paddyg12 жыл бұрын
Thank you Lucille!
@williamgardner27392 жыл бұрын
Yes i like it Paddy, but did you not think if you are exerting pressure from side to side, such as planning, your Workmate is going to slide away from you on it`s wheels.
@tombelanger54892 жыл бұрын
You could have painted the 2x6's before installing the plywood. Skip the tape.
@jayraysdiy8522 жыл бұрын
How is the separator working for you?
@IrishScott712 жыл бұрын
Hey PaddyD, loved the lesson. However, I honestly can NOT find a wheel balancing video explained how to do it 'simply' as you put it. I thought you said you might add one, but I also searched your video list and couldn't not find any lesson on balancing as well. Do you have any youtube links you can recommend providing easy steps in balancing your grinding wheels? Thank you!
@elmakario53012 жыл бұрын
Zzz z
@mikethebike2456 Жыл бұрын
🏍️ Wake up ! 👀
@thomassawyer65232 жыл бұрын
East Tennessee Good Ol' Boy.......thank you for the review.