thats the way im doin it today, good short video though. im not actually messin with the fuel pump thou just dropping the gas tank to replace brake hard line thats rusted out an leaking behind the tank. everything is rusted to sh!t.
@Carsgunsnfishin24 күн бұрын
Thanks!
@scotthumphrey80872 ай бұрын
I was looking for some insight but I don’t think you have a f***ing clue how to do this. My advice is don’t post a video unless it’s going to be helpful to others!.IMHO.
@RicksRides12 ай бұрын
Says the guy having to watch a video on how to charge drum brakes, seems like your the one that don’t have a clue 😂… but thanks for taking the time to leave a comment, feel free to drop a link to your video on how to change drum brakes
@buddyrebel_Garcia2 ай бұрын
Quick question I got the code B00 26 When I turn the steering wheel at a certain position, the airbag light goes away, but when I turn it back to normal, the airbag light comes on and the service airbag message comes on. Do you think the clock is busted? I recently replaced the steering wheel about two months ago, and I just started to have this problem.
@RicksRides12 ай бұрын
@@buddyrebel_Garcia it could be the clock spring but not positive, I was having a weird problem like that one time with the horn and it ended up being the turn signal switch, had a little brass button that wasn’t making good contact in the straight position but did when u turned…
@buddyrebel_Garcia2 ай бұрын
@@RicksRides1 hi thanks for replying. It actually was a clock spring. I replaced it and the code went away. I have no more issues. Thank you.
@garystafford-x6j2 ай бұрын
I tried it. Another piece of advice: Slice the foam backing about 1/2 inch in from the edge of the rubber (don't slice through the rubber). Then pull the strip of foam out to relieve pressure on the rubber (it lets go easily). I was able to pull the rubber much further around the plastic backing without the foam fighting me. Then I screwed it in like you did - no wavy bottom line!
@Braco3083 ай бұрын
Dammm thanks for that I just used gorilla spray adhesive
@GypsyMedicSTT2 ай бұрын
Previous owner did that on my current truck and now it's flapping off with a bunch of old glue on it.
@bryann.69854 ай бұрын
Need the name of the metal clip, can’t find the part # on eBay…
Thanks for the idea!! I ended up drilling 2 small holes under the 2 bottom screws, ran zip ties through the holes and through the clip to the left and right of that top mounted screw and it worked perfectly after tightening. I credit your idea for allowing me to come up with mine, appreciate you!!!!
@howardrodner23025 ай бұрын
I just used this repair! Thank you!
@jeanenegarcia32085 ай бұрын
Omg thank you!!!!! I needed this! Great idea!
@JuanCastro-zd3sb6 ай бұрын
How did you attach screws to the dash pad? Also after I completed mine my front signals light wont blink. We replaced the flasher and still the same issue. Was working before installation
@timberry91648 ай бұрын
So I refer to the Haynes manuals for a lot of repairs on my vehicles and they want you to take the whole dash apart like he's talking about the other guy doing...I knew that it sounded like waaay too much work so that's how I ended up here and this video was PERFECT...thanks for the info🤙
@2H25218 ай бұрын
I just super glued mine instead, I held it down into place while it dried. Worked okay, but definitely not perfect or exact factory looking. Certainly better than how crappy it looked before though.
@shelbygates508610 ай бұрын
Thank you for this video. Been looking everywhere trying to figure out this is gonna fit in my 72. Life saver
@RicksRides110 ай бұрын
It’s a lot of work with trimming out to make fit but it’s worth it, looks much better.
@johnscott683310 ай бұрын
What electric windows did you use. I want to add it to mine
@OneNation-v9y11 ай бұрын
Thank you for the video, I watched the video fortunately not because I have to replace my heater core right at this moment. But the antenna cable I was trying to tape the new antenna cable to it and it came off, so there’s nothing no way to pull it through now, so I have to take the dash part, anyway thank you very much. Very useful video. I appreciate you.
@RicksRides111 ай бұрын
Well I’m glad my video will be able to help and guide u through this process, hopefully it all goes smooth for you.
@johnwhite192 Жыл бұрын
What a nightmare I have 2003 xlt 2.3L automatic truck I don't suspect it is leaking bad but I keep smelling ainteefreez when ever I shut truck off I smell it pretty good. And if I turn defrost on early in morning it totally fogs windshield for few seconds I think it's in the early stages of going bad or worse I really hate messing with the dash its probably worth 800 to me let shop do it so I can have the warranty. I thought it was lot easier than what you showed
@RicksRides1 Жыл бұрын
Honestly it’s not that bad, just start it early on your day off, take your time not to damage anything since these trucks are getting older and the parts are getting harder to find.
@chrisavalos9521 Жыл бұрын
What’s the metal piece called that you screwed in? Looking for one and i can’t find the name
@RicksRides1 Жыл бұрын
A-pillar clip here’s a part number from a seller on eBay 134753199020
@miguelcovarrubias4976 Жыл бұрын
Does That Mean Your Heater Core No Good When It Starts Leaking Coolant To Your Carpet On Passenger Side
@RicksRides1 Жыл бұрын
99% of the time that’s what it is.
@miguelcovarrubias4976 Жыл бұрын
@@RicksRides1 Got It Got To Start Learning Mechanical Problems. Thanks For Your Response.
@rodneylester9233 Жыл бұрын
Poor video
@floribertoalvarez14 Жыл бұрын
What model is your Chevy
@RicksRides1 Жыл бұрын
It was a 2005 Chevy Silverado extended cab LS with a 5.3/4l60e.
@calebwhite5640 Жыл бұрын
This looks way easier than other videos I’ve seen.
@RicksRides1 Жыл бұрын
How it helps and your installation go smoothly
@carltoncarroll4821 Жыл бұрын
Promo_SM
@danielwelch5006 Жыл бұрын
Ok so where is the bottom 4th nut to pull evap core back. I got the top 3 but it still isn't pulling back.
@YourLocalHandyMatt Жыл бұрын
Delete this video you idiot it is absolutely unhelpful and you have no idea what you’re doing!!!! How about adding how to remove the E brake and removing the air box and moving the air conditioning unit out of the way!!!! 🤦🏻 just like an American always doing half the job
@Novoani Жыл бұрын
I used your trick and rented a pulley puller and the ball joint kit to get the front main seal on and it worked great. You saved my ass!
@RicksRides1 Жыл бұрын
After doing that video the new seal leaked worse then the last and I leaned a new trick, soak a paper towel in brake cleaner and after u remove seal wipe out all the old oil, repeat until spotless, the on new seal black RTV on the outer mounting surface and a lite layer of grease on the seal that the her Monic balancer rubs up against, and a lite layer of grease on the balancer it self then install, now I’m leak free.
@chancemcneely3498 Жыл бұрын
But why does it run like that
@Tyler.8212 жыл бұрын
I know this is a old video but if anyone’s wondering the two bolts on the driver side that he doesn’t directly point out are underneath the fuse box panel, took me a while to find them so I figured I’d Share
@timberry91648 ай бұрын
To the left of the fuse panel on mine and the one in this video
@jpnm812 жыл бұрын
Yep that's a ranger all right to close the door you got to give it the old double slam
@Oobeazy42 жыл бұрын
U ain’t worth a fuck
@mauriciorh36362 жыл бұрын
Show how you took off the dash that would help
@RicksRides12 жыл бұрын
I showed where all the screws and bolt holding it on, once you remove them it comes right off.
@seangowan74412 жыл бұрын
What year is yours?
@RicksRides12 жыл бұрын
2005
@jaredmellinger36482 жыл бұрын
How do you remove the pins?
@RicksRides12 жыл бұрын
First u have to remove the little grey plastic clips then use a super tiny flat head to work the pins out, I believe they had tabs kinda holding them into place
@jaredmellinger36482 жыл бұрын
@@RicksRides1 Thanks! I'll keep trying...
@skiwesser12 жыл бұрын
Are the struts very much harder to swap out at same time?? Same method with jack controlling spring under control arm? What should I look out for? Thanks!!
@skiwesser12 жыл бұрын
I just noticed this vid is 6 years old 😂🤣😂
@RicksRides12 жыл бұрын
I’m sure it would be fine, the car is heavy enough as long as it’s a complete car with the motor and transmission is all in tacked… it’s sad I have to even mention that but with all the stuff I see happening on the internet id just figured I’d throw that in… and even though this video is 6 years old and I no longer own that mustang I still own my original 93 mustang, the all black one.
@jasonl36862 жыл бұрын
Bro you’re the man. I just put lowering springs and new struts on my 03 GT. Then did some research and figured I should probably get new plates. Wasn’t looking forward to taking everything apart again, but this makes things way easier. Thanks!
@matthewroyston98912 жыл бұрын
late to the party, but my caprice has the exact same issue. permatex weather strip adhesive is some amazingly sticky stuff and worked perfect for me. part number 81731. it took really long to dry however so youll need to find a way to hold it stiff as it dries
@warbed12 жыл бұрын
Was there a code present like B0018
@offbeat-barnacle2 жыл бұрын
I did all of this and now my truck won't start, is there a ground or something that's in the dash that I could have unscrewed?
@RicksRides12 жыл бұрын
Make sure you didn’t trip the fuel shut off switch found in the passenger side floor board at the top of the carpet , And then double check to make sure you reconnected every connector including computer if you removed and all battery terminals
@jovanharrison43612 жыл бұрын
So my black wire fell out…can I just connect it in any hole or does it go in a certain one?
@RicksRides12 жыл бұрын
It need to be in a certain hole, look at the other side of the harness to see where it need to go on the harness it feel out from.
@lunisic2 жыл бұрын
great video. shave an hour off a 1.5hr job not bad appreciate it.
@sewerratt472 жыл бұрын
Great illustration !
@allenhall51592 жыл бұрын
How’d you fix the hard line I had the same issue happen when I did mine.not too sure where to find the line
@RicksRides12 жыл бұрын
You can buy all the hard lines and repair parts from Autozone or O’reilly
@ShskyThompson2 жыл бұрын
How to you adjust the camber to negative on this on other cars it’s sides.
@TekMan053 жыл бұрын
This video is really helpful. I've done this job once before a few years back and did alot more it seemed. Gotta do it again because the ebay one I bought is leaking again. Got a motorcraft part this time around. This procedure also applies to 95-01 Explorers as mine is a 2000 5.0. BTW, how does the airbag cover come off?
@justsomerandomasian4083 жыл бұрын
I just made it 666 likes nice
@terrancolonyone3 жыл бұрын
Helpful. The one thing I needed help with was the metal plate that is on the cabin side of the firewall just behind the ECM. It won't let the upper lip of the heater core cover slide out. I notice you had to take the metal plate off but didn't show how. Anyway, very helpful.
@valenzuelaedwardo3 жыл бұрын
You made it seem harder then what it is tbh. But definitely gave me a better perspective, then what i had in mind
@andyeveland3 жыл бұрын
I’m going to try liquid nails or gorilla glue with the screws then wrap it up tight with some straps till it dries. Hoping it will prevent the ripples. I’ll let ya know how it turns out. 👍
@RicksRides13 жыл бұрын
Yes please make a video or a step by step for us all to see. I’m curious on the turn out.
@stephenurban98802 жыл бұрын
How did it work out?
@andyeveland2 жыл бұрын
@@stephenurban9880 it came out pretty good. I ended up clamping it with a piece of angle iron and so large clamps. It’s still got some ripples tho
@redperez28533 жыл бұрын
I got a service charge system
@ivanivonovich98633 жыл бұрын
Did this job on a Pinto once... A lot easier than this is. Just reached under the dash and removed a few clips and wolah! All done. I do not look forward to doing this on my truck.