Good man.

Nice

Couldn’t have found a better k wire removal video this was awesome

Hey hey thankful TODay helluva 🎁

please tell me, I can't install an alarm with autostart on my v strom. tell me how to find the wires from the ignition switch and the starter button under the seat. I can't find them. thanks

My 08 vstrom 650 does not have that plug

Hey, amazing! I just bought two ammo cans. How do you attach them?

Great video real informative straight to the point 👍

Why remove fuel from tank? Insanity?

10 years later and still useful. Thanks brah - College student

lololoolol

You didn't show the removal of the front bolt on the front of the tank at least I didn't see it

Thank you sir

Great job!

Monkey butt... :) :) :) We will be staying there in September... Never slept in a caboose before. I love new adventures!

If you turn the bike off won't you lose the codes

I got one of these slightly better built than this one, with better base (metal) and came with locking nuts. It... Works. For a mini bike (dax 125) does the job to hold a modular helmet (Medium) and a summer protective jacket. Winter jackets won't fit with helmet. Where you had your orange stripe, mine have a silver reflector. Awina 9001 is one of the names.

You could really benefit from having some T handled metric allen wrenches. Sure would speed things up for you.

Hi can you update us on your liver mass?

Update please!?

Thanks!!

I had a bunch of o-rings come out on that pipe for the fuel line. and now I can't re-connect it after removing the tank. Any advice.

Thank you! Those push clips were getting me

I have the 1000 and I'm nit seeing how to remove the seat?

thanks pal !

Very useful video, thanks for sharing

WHERE IN KINGDOOM SUDIA ARABIA

Thank you

Great video and thank you for posting, I probably wouldn't have tackled this without your help. I got deployed 3 time and there is gas about 3 years old in my DL650 I need to remove.

Thanks!! Good vid

Helpful video

I did the same on a Honda shadow 750 I had a few years ago. I just put hard tail struts on the bike, got shorter exhaust(so the cans would hug the bike, cause I lived in the French Quarter, New Orleans) and made a hard mount for the cans connecting to the passenger peg brackets. Worked awesome! Plus the cans were roughly the size of Harley bagger saddlebags. Plus got an old CB rack which I fitted with some flat bar from Home Depot. So I could live off my bike with no issue. Put a small box on the back and did Door Dash and Uber Eats. Plus I made a shotgun holster(out of PVC which I heated and formed it to fit my shotgun) on my forks(which I extended) for my Mossberg Shockwave cause I drove anywhere in New Orleans even after dark. I miss that bike.

Either the lowering link bearing is loose at both ends, or you have some other bearing that is failing. The rhythmic rattle is usually a sign of something gone very bad. Best to take off the wheel and check all the bearings and bushings from the wheel to the shock. Usually one wearing out is caused by something else vibrating... or not lubricated... or overheated. Nice helpful video tho!!

1.88 mile train tunnel 10mile south of Snoqualmie summit. 47 16 00 n 121 21 35 w enter. 47 16 42 n. 121 19 26 w Great VIDEO

I wish there was a duel sport Video that showed locations and Entrance points in western Washington. I used to just follow my dad.

Hey, I installed ammo can panniers on my Klr 650 and get death wobble at 70 mph. Any wobble with yours?

I replaced mine with a PUIG. It is decent, just wish I didn’t bet the smoke tint

Passen in den Tank auch 35 Streuselschnecken und 65 Bratwürste?

Is there any need for a heat sink for this component? I guess the bracket you made probably works for that purpose...

haha bung

Great tip... BEST METHOD Video on this subject in all of KZbin..!!!

I have a Lambretta Uno 150. I think it's the exact same bike that is rebranded. I'm currently looking for the cheapest place to get brake pads for it. Do you have any contacts for them?

NO that is not a lowering link failure that is a failure of the suspension setup.... increase your dampening on the rear !

Lower the tipple trees in the front as well ! this will keep the steering geometry the same I lowered my XR650L by at least 2" with the adjustable lowering link... with those you have to make sure you still leave enough threads in the coupling nut to hold strong ...if you only have 2 threads in the nut it will rip the threads out and you'll be sitting on your tire ! I left 5 threads in mine.... I have a 30" inseam and can flat foot my bike , but I also cut down the seat and lowered the front...and cut 4" off the side stand.( so technically i lowered it 4".I don't care what the product info said it lowered it 4")

It's called a spill proof cup. Try it

Ok sorry. I couldn't see the prongs until I watched it on my TV. I will try to do it myself. Thanks for the information.

I can't tell which two holes you are talking about. I changed my filters and now I have a F1 code.

Привет.Как показали себя на асфальте?Шумные? Как дорогу держат?

About using dish soap as a rubber lube when installing tires or bushings on aluminum wheels or shock absorber bodies dish soap , Bath tub soap, laundry soap, shampoo, etc.. generally has LYE in it. LYE, also known as sodium hydroxide is the natural born kryptonite for aluminum. If any soap of any kind burns your eyes such as shampoo or shower gel soap, or a bar of soap, if it burns your eyes, that’s the sodium hydroxide/LYE in the soap that is burning your eyes. It feels like it’s a great lubricant because that is the ingredient in soap that makes it feel so slippery and slimy. But you don’t want to use it as a lubricant to install a shock bushing in an aluminum shock or when installing tires on aluminum wheels..

Thanks so much for that. Great video.