Great vid! Where do you find this solder iron for $55? Thanks!
@GibsonAviationАй бұрын
can't go wrong with ca hinges.😀
@WayneCook3063 ай бұрын
I will say it again why spend the time and money on a nice scale model as this one is and fit a two-stroke engine does not make sense.
@avionette3 ай бұрын
4 stroke engine in this models!!?
@mikec41143 ай бұрын
I needed this in 1980 when I first attempted building. I had the RCM flight training Handbook 1 & 2 and Al's Hobby shop, Elmhurst ,IL
@alexherrera39184 ай бұрын
what is the difference in weight between oratex and regular ultracote?
@davepatrick99054 ай бұрын
Great Video....but LOWER the music...a lot
@calvinlockett29635 ай бұрын
the STAB?????? really???? cant finish words????
@easystar1235 ай бұрын
Fantastic video and very well explained and very helpful. Thanks for sharing.
@balsausaairplanes65663 ай бұрын
Glad you enjoyed it!
@lucienrios29976 ай бұрын
Hi very nice video my question is if I’d like to apply PolyBruch with spray gun may i use directly from the can or i should use thinner Thank you
@JKinFW57757 ай бұрын
Do you have the rest of the build that could be posted? Thanks
@dougs49447 ай бұрын
The Fokker scourge lives on!
@andretrishrousselle63307 ай бұрын
Very good information thank you lots
@ripper91117 ай бұрын
Love the air wrench sounds when fast forwarding!
@blue03r68 ай бұрын
isn't oratex Ultracote?
@balsausaairplanes65664 ай бұрын
no
@parkerds108 ай бұрын
Great tutorial. The music in the background is not necessary, just saying.
@lacrossewisconsin9 ай бұрын
I love the instructions! However, I think you need a better microphone and maybe some more light and close-up video and high-resolution, the second video was out of focus.
@Jesusistheonlyway869 ай бұрын
How thick is the wood?
@balsausaairplanes65669 ай бұрын
1/8 inch
@TheBigChinoDon9 ай бұрын
This was recorded 6 years ago. I was "in" the class with Chad. I learned a lot and still have my XL.
@JKinFW57757 ай бұрын
Do you have the complete build or was there only 4 videos
@TheBigChinoDon7 ай бұрын
@@JKinFW5775 Sorry, I don't have any and I don't recall how many videos there were.
@dsnyder059 ай бұрын
@Balsa USA Airplanes, Will there bee a Week 1 class posted?
@balsausaairplanes65669 ай бұрын
I'm going thru the videos, If we have one it will be posted
@JamesRCPlaneTech8 ай бұрын
Nce!
@josephkerkau25209 ай бұрын
A shop vacuum is pretty handy to get chunks out, and also, outside the part, on the print, and all the other loose Debris...
@michaelalix49439 ай бұрын
Went on useless Balsa USA website, nothing but a countdown timer and the person chatting seemed to be a retard or something. Maybe it was a retarded AI, I don't know, but they lost a sale. So HA HA on them!
@josephkerkau25209 ай бұрын
No matter what the Grain is doing. If you use windex on the outside of the curve, it will fold over for you. Ready to glue, really nice....
@josephkerkau25209 ай бұрын
I use a stone wheel on my full-size planes and the little one. It is very sharp!!
@josephkerkau25209 ай бұрын
The best cover you could use for your plans is a plastic thin film. The roll at joann fabricks, in the upholstery section. It is strong, thin, and (very clean like glass), and inexpensive. C a glue and regular glue like apoxy does not stick to it.
@Jesusistheonlyway869 ай бұрын
What melting temp does the solder need to be?
@balsausaairplanes65669 ай бұрын
360 to 370 degrees F
@thomprd10 ай бұрын
Dang, that music over and over and over and over again
@kokokyoushi10 ай бұрын
The copper wire should have been cleaned after touching it with fingers, then flux applied.
@dirkgrobler217911 ай бұрын
Where is the video for installing hinges?
@balsausaairplanes65669 ай бұрын
kzbin.info/www/bejne/iXWmpXqXg5yLhs0
@neuhausr11 ай бұрын
Great instructional video. Thx
@guypehaim1080 Жыл бұрын
What size engine did you take out and what size motor did you replace it with?
@kokokyoushi Жыл бұрын
What tool is being used to cut the cable so neatly?
@petercyr3508 Жыл бұрын
Ready to use the BUSA nicopress, turnbuckles and thimbles on my H9 1/4 DVII. Already used on pull pull rudder. Nice. Brand X plane. Sorry. Really wanted to learn best way to install turnbuckles. Ahhhh, a short cable run on one end. OK.
@Workerbee-zy5nx Жыл бұрын
Gnome radial?
@GibsonAviation Жыл бұрын
which engine? would zenoah 38 work
@seoexpertforhad Жыл бұрын
wow
@UrsBracher Жыл бұрын
Achtung, der Sturz könnte zu viel sein wenn das Flugzeug auf dem Heckrad steht und per Augenmass gemessen wird.
@laurenceboag2325 Жыл бұрын
The Box is 3.5 inches off the mark here. Way too far back.
@unit0033 Жыл бұрын
sounds like hes saying sodder,
@p3arljam26 Жыл бұрын
How many flights / charges do you usually do before replacing those batteries?
Great series- If I may offer one correction! The sheeting on the wing center section has the grain in the balsa going leading edge to trailing edge. The sheeting should go span wise .
@gwrrolan Жыл бұрын
👊👊😊😊
@saittafpv5846 Жыл бұрын
When stories the videos for the Cub gonna be out
@anthony3D Жыл бұрын
Super vidéo 😊 c est très intéressant 👍merci
@AviatorJohn70 Жыл бұрын
Another great how to video by Chad.
@AviatorJohn70 Жыл бұрын
Great video, bring Chad back!
@CliffHarveyRCPlanes Жыл бұрын
Great video, the iron does a great job at that size, could you use a small blow torch as well?