This video is very misleading. You don't look wind burned you look like an idiot. Didn't even show one step of the install.

If you were going to try to open up the other exterior wall, how would the bracing be different? There is still a load, but not as much for several reasons. When the floor joists don’t run the correct way, how to you temp support it? Would you attach a ledger lvl but run temp supports to the ground like on a porch post replacement? Or are you relying solely on the lvl being attached to the corner post and then stretching across several studs that are unaffected past the opening to support the wall? And the temp wall below as only to hold up the joists while you cut away the studs that weee holding them?

Well done. look forward to more

That trailer is real close to what i want . 16 tilt 8 stationary. Have you looked into bucket bunker??

Where did I can buy adapters for siding?

80 bucks? 😂 I just made my own for free on my Bambu P1S

Awesome 👌 sharing this with an awful rental company that does little to no maintenance

Were you req'd to add squashblocks or stiffeners for load bearing walls at the i joists?

Few questions on the drawers and uprights... Is this 3/4" plywood? What depth for the dado that the bottom of the drawer slides in? What was your method for cutting all the dados?

Interesting use of a drill pump. Thanks.

What didn’t you like about the tilt?

First

You are making this very complicated check out Bob Villa

That’s nice. From amber to white backups.

Awesome thanks 👍

Is this the go-to nailer for ringshank asphalt nails and vinyl siding? Any better double duty nailers now? Thanks

I’m going to buy one-- I’m redoing my deck but outside of that use a belt sander only Rarely so I’ll Bite--

Ánimo, Dios te de paz, sabiduría, bendiga tu entrar y tu salir. Búscalo mientras tengas tiempo, y mira que tu vida va a cambiar, entrégale a su Hijo Jesucristo tu vida, tus deseos, tu familia, tus pasos. Todo cambiara en tu vida. Acércate a una Iglesia Evangélica de tu Ciudad. Desde Veracruz, México. Te saludos. Marcos Peralta

To be clear, you can run 15 degree collated siding nails in this gun? Even thoufh they have a slightly smaller heas than roofing nails

The Left or Rights determine which side of the snips the "waste" will peel upwards. For beautiful clean and sharp cuts and miters .....rooks😢

This is so rare - tradesman "we're going to this about what would look better and not whats easiest". definitely being paid by the day haha

Welcome back brother! Don't change the channel name. Bearded Builder suits you!

Where is ACE?

No joke, just yesterday I thought to myself, that dude hasn't uploaded any videos in a long time. Weird how that works, the next day you give an update. Been in the same boat more than not lately. It's unfortunate. Thanks for letting us know what's up!

This is HILARIOUS!

Mount some rubber on rails otherwise rubs all paint off

Thank you! So rare to find an exterior support wall video.

Where is part 2? The finished product?

Informative video. .. I'm a truss designer it's a pleasure if I can help in any case of trusses designing

How hard was it installing the new ceiling joists? Did you throw 1 at a diagonal to the top and have to bow the other end while lifting

I like these, I'm still stuck in the weatherproof black pigtail socket era!

how you climb up to the top to get the ladders??

Just came accross your video, do you have thevideo on how how you went about insulation and what you used. Thanks man Looking forward to watching more

We cleated a couple 1x6 together to lay across the brake C’s for a deck for the stock your working. I like combination squares for repetitive short dimension marking. Small notched and bent scraps of coil stock can also make repetitive marking gauges. You don’t actually have to make a mark if you use the gauge to set the reveals in the brake.

What size is the hydraulic drain plug?

How do you stop them from falling out when going down the road😅

Hey Guys!! Thank you!! I was about to expend over a $100 bucks!

Do you think you could get a car on it or would the ramp be to steep and it bottom out?

Should have put tongues on that final strip. Rabbet them on your job site table saw. I probably would have started at the ledger with the subfloor so you can get a tongued strip in. T&G tends to mate up better if your hold the leading edge fasteners back from the edge until the next swath is run.

Don’t really like those OSB band joists. That material is notorious for splitting when you nail in the edge. How’s it going to reliably hold plate nails never mind subfloor nails. I built a 20’ garage with those same I-joists but I used solid sawn 2x12 plus a 2x strip glued and nailed on top to build it up. I did put a 2x6 strong back on the bottom center line making sure the joists were plumb at that point.

Thanks for the explanation! Trying to figure out how to do this on my garage thats being built. Can we get an updated look on the barn? Im curious how the trim came out and the 3 colors look.

I'm deciding on the right trailer for me. What made you go bumper pull instead of gooseneck ?

How do we get the attachments? Could you put a link?

How do you pop out certain panels without having to remove all of the vinyl panels?

Question for you: I am hobbyist JD 1025 R small tractor owner. Been thinking of starting some gardening too, and shopping for trailer that can be multipurpose. 16x7 utility twin axle is what most people get. But the PJ T1 tilt single axle 7000# 16 ft caught my eye. The challenge will be to add sides for compost/mulch. The easy forklift access on the front make it easy to pickup an hvac unit, etc. But, would that be an over kill? Or impractical since I would need to make up sides that are not a ready made option. And then its certainly a few $K premium over a landscape trailer.

Excellent videos.

Thank you for the informative video. Looks like you opened up around 16’. I need a laundry room for my 1957 ranch in TX - it was never in the garage, was probably in kitchen. Currently in a sunroom tacked on the back of the house that I call the EZ Bake oven - it’s 110° to 115° F in summer & freezing in winter. It’s time and your video gives me hope. Of course I have to relocate the kitchen to go through the back wall of the house - I have a great GC I trust, but still need to see the process to calm myself down!

Why do you over lap the tape?

Can tou post a link for the siding tips. Great video, THANKS!

Hi Thanks for the video. I have a question. We are renovating garage and our contractor has created frame for ceiling using 2x4 only. Can it hold up the 1/2” drywalls ?