My gear is loose. How would I tighten it.

It helped me a lot, thank you for the information, I already repaired mine, only 2 fuses, thank you

WHY DIDN'T YOU MAKE THIS VIDEO AT LEAST 15 YEARS AGO!!!! 🤪😜🤪😝

This was the Bane of Mt grandad's life, my nan had so many old tins of Quality Street that were full of light strings and other with bulbs. 😂

How do you take the back off .i need to change av cords

Any solution for LEDs?

Hey did you ever return to the ps2? Or did you just give up on it

Quite a helpful video, thanks for the upload!

Thanks lots , I'm gonna try it now

There is two versions of the Samsung drive version a and version b

today's sponsor is me HAHAHA

Thank you very much, you helped me a lot, I had the same problem and I did exactly what you said and everything works thanks

Hello, the more stick you populated often makes RAM unstable, and usually the advertised speed is guaranteed on 2 sticks only (especially since that's what most people is buying and putting on their system anyway). Since you populate all four that may explain the need to downgrade the speed. I think that particular kit is rated stable at 4000 for 1R, 3600 for 2R and 3200 for 4R which may explain why the expo profile offered was 4000 in the beginning. Doesn't really matter anyway since around 3200-3600 is the sweet spot for AM4. Most importantly hope you have fun on your new system!

i took diazepam, before upgrading to 64 gb ram. chrome is doing illegal settlement on my ram.

Usually when you enable xmp it also raises the ram voltage to 1.35v, if you manually set it to 3600mhz it most likelly didnt change the voltage and i guess that why it wasnt stable at 3600mhz. So i think you can set it to 3600mhz but also need to raise the voltage to 1,30~1.35v. Also you may be able to undervolt the cpu at least 100mv, at least for my ryzen 3600 it set the vcore at 1.4v if set to auto, and i was able to set it to 1.275v and its stable.

Btw, thermal paste is supposed to squeeze out. All that should be left is the tiny amount to fill microscopic imperfections in the machining. Glad you found the actual fix tho!

In the UK this is sold as the VAX Blade 4. While it is to be expected that you have to remove the brush bar occasionally to remove the build up of hair, hair gets behind the brush bar drive and gets into the bearing. The bearing itself is fitted into the plastic shell of the brush bar. Hair gets in there and eventually seizes the bearing. This will either result in the drive cog being stripped, or the bearing spinning in the plastic casing until the plastic starts melting. The belt tension then drops off as the brush bar is no longer being held in its correct position. It is also common for the casing to crack as yours has during the jolt from the initial seize up. Build up of hair behind the brush bar drive (inner bit) is not visible when the bar is removed it is not possible to see the damage building up. You could of course remove the inner drive (yes that is a left handed thread) regularly and remove any build up, but this is a glaring design fault that mars an otherwise good product. A lot of people are reporting the wheels breaking off as well. There is no fix really and no spares so you can. Mine is very helpfully just out of warranty so i am stuck with buying a new floor head for £60 that i know is liable to fail as the original one did. If anyone knows whether the Blade 5 floor head fits that would be useful!

Puts a review on youtube... " i didnt even bother taking a picture of it" dude...wtf is the point then? Youve literally uploaded NOTHING

i only eat fast food once or twice a year but the rubbish is worse than it use to be. my parents were right all along. im glad my dad only won on the horses once or twice a year

You could have put together a better review than this. Way too short and you didn't back up your negative feedback at all. I am pretty Jacked about the burger and this review didnt even give me reasons to feel any other way,

In case anyone's wondering why I sound so mad over a fast food meal, those three combos cost me just over $50, which is another rant in itself. However, my wife and daughter, who are the real Spongebob fans in the family, were also pretty disappointed over the "afterthought" nature of this brand deal...

In case anyone's wondering why I sound so mad over a fast food meal, those three combos cost me just over $50, which is another rant in itself. However, my wife and daughter, who are the real Spongebob fans in the family, were also pretty disappointed over the "afterthought" nature of this brand deal...

We got ours unfortunately from a passing of family on my wife’s side of the family. I hooked it up today and started playing. I heard a soft pop and my game froze. Tried turning it off and back on again and got the red green flashing with the error message. I didn’t see what error code it was. I was baffled because I never had an issue with the original Xboxes doing this in the past.

I would get a schematic and start trouble shooting the eject line and checking the components around the video circuits. Their are resistor arrays attached to video out chip IC211 on the service manual. A short test on capacitors around the cpu and gpu is a quick way to test if they are dead or shorted.. I'm not 100% on this next statement but I think each bank of resistor arrays (RB246, RB244, RB242) is for the R G and B signals to the IC211 witch is the video DAC. they are an easy thing to test. Both the chips you are replacing are motor controllers. They wont help the video out issue. I would start with the video issue first as that will tell weather its worth chasing the motor issue.

Hey man, I have the exact same issue as your other GameCube board. Have you figured anything out on it? I don't see a dollow up video :( I don't believe it's a reballing the CPU issue, I just attempted to install a pluto 2ii on my dol-101, and now I'm having this exact issue. It was perfectly functional before, after a few enamel wires were installed it all of a sudden killed my GameCube, so yeah i don't think its a cpu issue. I think the AVE N-DOL chip on the board may have went bad, which is gonna be sad for me 😅 Edit: through trail and error with diagnostics, I've found that my fuse is receiving 12v but my power regulatory circuit is not functioning correctly, which is interfering with actually turning on the CPU & GPU, some sort of protection is tripped, and it cuts off the power to the coils in the circuit, cutting power to everything lol I believe this is the same issue as you, and I'm currently looking for the Power Regulatory Circuit schematics for the DOL-101 (Not the power regulatory board for the DOL-001) if anyone has em lemme know.

That looks like a magic v7 mod chip. As someone who has doen many ps2 mod chip installs I would call that a verry slopy install. It should be mounted on the qfp chip next to the bios chip and have muchshorter wires and they should be managed with a dot of glue to hold them in place. Also when installing the drive ribon cables its easyer to leave the metal shield with the drive clips off and putting it on after the cables are in.

The bushing on this gear is full of hair. There is a snap ring on the inside. You can take it off and pull it apart and clean out the hairs. I dropped liquid candle wax into gap between the key for the brush and the housing. I am hoping that the wax is minimizing the gap between housing and key so that it will let through less hairs.

New Sub: Dryden, Michigan. Never got to try one back in the Day. Just picked one up in Beautiful Condition, but it is having issues loading games. Seems like Tapping Controller one, or Occasionally Tapping the console itself causes the Screen to Glitch, but Typically it will not load past the BIOS Screen: Removing/Replacing a Cart will bring the BIOS Screen back up, but some of the Letters Randomly have Different Colors and the screen just sits there. The Cartridge Slot Itself doesn't seem to take a Cart directly in, You have to Rock it.. I just Tore it Down, everything looks nice, No Dust even. Best Video I've found so Far. Thanks

" F A W E R D"

I want new belt for it , i have same problem Which size of belt should I get?? Thank you

Hey just wondering when will you return to the ps2 with the magic smoke?

A lot of people thought this one wouldn’t red ring..

Ive damaged that ribbon cable before too, I think it happens to most ppl who crack these open for the 1st time. Not sure i'd run jumpers long term tho, id find a parts board to grab those 0 resistors from.

hey! I was having the same issue, and found this video super helpful! the belt, and the mechanism it spins on were fine in my vaccuum--but the horrible screeching noise remains! Would you recommend some oil on the mechanism that spins the cylindrical brush? this vaccuum sucks, but i don't want to toss it since it isn't that old!

Oh trust me….that’s not the only original xbox with red ring of death

so i know some people are shitting on your teardown technique in the comments, but god damn this was an entertaining video. I appreciate you keeping in the flubs and foibles. and I hope you maybe do an RGH hack on this in the future! also, BONUS GAME, WOOOOOOOOOOOO

I would recommend delidding the CPU, as there’s thermal paste underneath which needs to be replaced. Josh Davidson has a video on that, definitely recommend his channel as he’s an Xbox 360 expert

Hello guys, please can you tell me what kind of value is the WR 644 resistor, located next to the chip, because although so carefully I tried to put the clamps on the chip a couple of times because it was failing to read it, but I managed by mistake to undo the resistor there and never found it again. It's extremely small. Thank you!!!

The "little gasket thing" might be clumped hair tightened together. I've had that a few times. Hair shouldn't be able to get in there but somehow hair gets everywhere. Regards from a Tom :)

The official Vax repair video failed to realise that real-world gets dirty, grimly and worn. Also that there's usual more than 1 problem before 'normal' people, like my aspie self, get around to bothering to fix side-issues in our lives. Regards from a Tom :)

Ahh, I lifted the front lights off the plastic cover. Luckily it wasn't glued in. I hadn't thought of unplugging from the mbord. <shrugs> other than that my Vax repair was identical(ish). Thanks and regards from a Tom :)

Brilliant! :) This video was a huge help. I'd gotten stuck but unclipping the top panel gave access to the couple of screws that were blocking me. Different model, heck different make but similar enough to make sense. Thanks and regards from a Tom :)

This was a very enjoyable to watch. I myself have opened up 2 ps3 all the way apart to clean and replace the thermal paste. I have a 2nd hand Xbox 360E that I want to disassemble, clean and apply new thermal paste. I also got a PS4 slim recently from a pawn shop to do same procedures. I laughed when you said wooden fork when it was clearly a knife. lol

This is a Waitsburg 4GB, which is a Corona version. Most of the Corona versions have those resistors that cause overheating, there isn't really any known reason for why they fail.

I fixed a samsung dvd drive by putting a working pcb board in

Only some of the slims had the 4GB flash included. The NAND size varied as well (matters if you do the RGH3 mod). I bought 3 or 4 from eBay last year and I think only one of them had the internal flash storage. Luckily they just use standard 2.5" SATA drives, and you can 3D print an enclosure for using your own drives as well. Plus you can plug in a FAT32 flash drive. I was expecting you to do a lot worse with the clips when I read the comments first. They really are a nightmare when you haven't gotten used to them yet. I think I wrestled with my first 360 Slim for an hour before I got anywhere, but after doing a few I can get them open no problem. This is my first time hearing about those 0 ohm resistors, that's a pretty interesting problem.

Nice video

maybe worth it to repair yourself if your going to use it but not paying someone as you can find em for like $50.

Love your vids bro

Omg cute kitty. Good vid. 👍😸