What are different tyoes of joints used in frp piping
@balasubramanian87386 ай бұрын
In how many ways the frp pipe spools can be joined
@SameerMalik-bw3cb7 ай бұрын
Frp ka kaam hai job kar ni hai
@Emezepe3 Жыл бұрын
What are some good tools to have for this
@malkinsz80 Жыл бұрын
1 step - train Step 2 -tissue mat + 3mat, and press this program into the chamfer. 4 step putty 5 step train 6 main program Making a chamfer to fill it with putty is not right !!! If you are not going to put a protective layer with tissue mat, then it makes no sense to make a chamfer!
@WanXinFRP Жыл бұрын
We are specializing in the manufacturing, design and development of various FRP products, including FRP pipe fittings, FRP flanges, FRP Elbow, FRP grilles, FRP storage tank containers, FRP winding equipment, FRP pipe molds, etc.,
@shohelrana30 Жыл бұрын
কোন কেমিক্যাল কতটুকু দিলে কি হয় একটু জানিয়ে দিন
@shohelrana30 Жыл бұрын
পাইপিং ল্যাবরেটর এর কাজের কেমিক্যাল গুলোর নাম কি ভাই
@cheyennemedicine2853 Жыл бұрын
What is the clear paper used to lay the material down?
@vapaustuonelassa Жыл бұрын
Muovia, muovia, muovia.... Nämäkin Käytössä "ehkä" 100v Mutta ongelmajätteenä vielä varmaan miljoonan vuoden jälkeenkin...
@Perintis0623 жыл бұрын
Salam.. I am from indonesi
@macktyler52683 жыл бұрын
I have a 4” pipe that sticks in a 30” frp pipe or it’s actually the underground sewer but I need to make a frp weld wrap where the 4” branches into the 30”. I’ve got all water stopped, I have the old existing weld ground off and it’s clean. I will put putty in the 1/4” crack before I weld. My question is does anyone know if they sell a 4” branch connection kit. I’ve not done this in 25 years but I believe I remember just using a kit and cutting short pieces with a split in them half way into so it can adhere to the 30” and 4” and same time or rather go on around the connection. Just a shot in the dark if anyone understands what I posted and if anyone has purchased a branch connection kit
@anilkumarsreekumaran65783 жыл бұрын
Are these steel moulds for flanges?
@johnveloz96404 жыл бұрын
How long do you allow each stage of epoxy to set/dry?
@litekcomposites9213 жыл бұрын
Apologised for the late reply. we are using vinyl ester and it take appx. 2 hrs to dry
@geabea28064 жыл бұрын
Agree with comment above regarding pre-gel / bog used in the beveled area of join. Even rovings wouldn’t do a great deal. There’s no extended stagger or graduation in the additional layers , no mention of overlap length or the stagger of overlap locations ( 12 o’clock- 4 o’clock -8 o’clock) let alone the fact that it’s CSM used in joining laminate! Use triaxial weave with the uni running along join , 20% over lap and increase ply width each layer . Remove air by screening by hand massage then wrap in stricture ( high temp stretchy clear film ) to consolidate . Use peel ply between laminate and stricture if coating necessary otherwise coated or add additional laminates within green stage of cure ( chemical adhesion ) OFFSHORE OIL & GAS method
@angkiykumar67924 жыл бұрын
All chemical name
@muhammadazlankamaruddin87985 жыл бұрын
how many layers that i need to wrap with fibreglass sheet on 2",4",6",8" & 16" diameter of frp pipe?
@nivethamathi45895 жыл бұрын
wantad irutha sollaum
@sunjune62155 жыл бұрын
Tis is useless video... to be frank... at site condtion hw can u do tis kind of lamination by rolling pipes..tis lamination luks like surgery being done inside an ICU...
@MarcosAntonio-ec6wv5 жыл бұрын
Neste caso ae eu uso foi rolving pra Barreira Química
@hamdihamaadi60516 жыл бұрын
Pourquoit le mastique c'est une faute
@syedsansar30644 жыл бұрын
What they are putting white second layer
@JOEGGGJOE6 жыл бұрын
I would of wrapped a strand/s of woven roven in the beveled gap first with the slurry mixture you made. That slurry is more of a filler with no strength properties.
@worldnews28936 жыл бұрын
Pls tell the resin formula
@sunjune62155 жыл бұрын
WORLD NEWS உலகச் செய்தி resin ke enna formula venum?
@waydesemmons64996 жыл бұрын
please give email address so can inbox my questions