Phraseblaster

Пікірлер

@s0dfrumbehind 12 күн бұрын

That's high-standard tec-pr0n 😁👍

@neoradjoao7701 4 ай бұрын

Hello, what did you do with the eject button on your cartridge? THANKS

@Phraseblaster 3 ай бұрын

That's the downside with this kit. I needed to remove the two "ramps" that push out the cartridge to make space for the PCB. So the eject slider can't be used anymore. But this isn't a big deal. You can just pull out the games.

@blurplemurple4960 4 ай бұрын

i see that ur console has a modchip

@ahmz1404 5 ай бұрын

Why does my back cover not clip back in properly? I have the exact same controller, everything looks the same, but the bottom bit below the joysticks does not clip back in properly, so the analog button is too depressed

@shannonhenson609 5 ай бұрын

What kind of spray cleaner did you use on the speaker fabric?

@Phraseblaster 5 ай бұрын

Hi, i used a carpet & upholstery cleaner spray: www.dm.de/denkmit-teppich-und-polsterreiniger-mit-aktivschaum-p4058172185540.html

@christianpedersen324 8 ай бұрын

Hi Phaseblaster. Thx for the video. Used it this morning step by step and healed my 690es, and it is working fantastic again.....hoping for the next 30 or so more years😊

@Music-Tech-Life 8 ай бұрын

Wow! What a detailed job. You have great skill and patience.

@nightruler666 9 ай бұрын

Are instruction included with the kit?

@Phraseblaster 9 ай бұрын

You can find them on the creators website: etim.net.au/nesrgb/

@aubsion2670 Жыл бұрын

Spin

@thatguyalex2835 7 ай бұрын

Interstellar theme intensifies. :) Ro-ta-te.

@aubsion2670 Жыл бұрын

Bruv

@vigna8878 Жыл бұрын

my Ta--f690Es sound bad low gain and dirt sound this operation will help?

@mutatedteenagegirl Жыл бұрын

The ultimate return

@treystewart544 Жыл бұрын

It’s like a saw blade spinning cutting the pine trees 🌲🪚😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎😎

@olehmukhin369 Жыл бұрын

by the way, could you explain one thing ? I've tried to adjust bias ( should be 24 mV after 10 min after warming up - in service manual) and noticed that after 10 min I have 24 mV, but after 20-30 min, when elements became warmer, the voltage is 20-21 mV. is it critical ? I have no experience with amps, unfortunately. thank you in advance.

@olehmukhin369 Жыл бұрын

thank you for tutorial, useful. for another homemade engineers : make a note of shaft position ! and good idea to check position of selector before soldering .

@lexi_6669 Жыл бұрын

I……. Going all the way is interesting (I’m new to the pinball scene, own 0 cabinets, have cracked software on my laptop) but… the eyes phase is EXTREMELY unsettling in Pinball Arcade…..

@campampates Жыл бұрын

WOW>...amazing outcome...kudos to you man.

@hadrosaurus Жыл бұрын

really nice work. where did you find the vinyl wrap?

@Phraseblaster Жыл бұрын

Hi, thanks! I used this one: www.amazon.de/gp/aw/d/B07R4YJJ71

@hadrosaurus Жыл бұрын

@@Phraseblaster awesome thank you 😊

@lancewilson83916 Жыл бұрын

It's nice to be the 200 person who liked the video

@caturlifelive Жыл бұрын

Somehow this video can make me sleep 😅😂

@kennerfee100 Жыл бұрын

so thats what a spinning disk looks like

@jakobbrink4682 Жыл бұрын

I tried doing this but may have messed it up somewhere in the process. Should all 3 wipers face downwards like shown at 2:17? Right now the motor doesn't run when I try to change inputs. Only the lights change.

@Phraseblaster Жыл бұрын

As far as i remember the motor axis is keyed, so as long the wipers face in the same direction, you should be fine. But i don't know why your motor isn't turning. Maybe there is a service manual explaining the circuit? I'd check the solderjoints on the motor first.

@jakobbrink4682 Жыл бұрын

@@Phraseblaster I fixed it - it was a cold solder on motor, thanks

@Phraseblaster 2 жыл бұрын

I've made a new version in 4K: kzbin.info/www/bejne/p4mnommgr9OIkJo

@АндрейКотов-е9н 2 жыл бұрын

Great video, thanks! Tell me, what is the output voltage on the transformer?

@Roses4reRed 2 жыл бұрын

This is a great tutorial. Is there another way to clean this without desoldering the board?

@Phraseblaster 2 жыл бұрын

Hmm, i wouldn't recommend it. You could try to get some cleaner through the underside of the switch. But you should then move the switches to clean the conductive tracks. But that will not be possible with the motor connected. I think desoldering is the easiest an most reliable way.

@ryanabrahart5300 2 жыл бұрын

Grovehill & Woodhall Farm Adventure Playground

@marcelvanooststroom1733 2 жыл бұрын

Great tutorial. Before you start, do you need to set the input selector in a specific input like phono or tape 1?

@Phraseblaster 2 жыл бұрын

As far as i know, this shouldn't make a difference. But the wipers should face the same direction when you reassemble the switch.

@hossammoghrabi1021 2 жыл бұрын

good video and production. keep going.

@sawekschauer6846 3 жыл бұрын

Great tutorial. Thanks to him, I healed my TA-F590 ES yesterday. The source selector was also very dirty. After cleaning, the amplifier sounds like it got a second life. Thank you and best regards :).

@Phraseblaster 3 жыл бұрын

Hi, thanks! That sounds great! :-)

@m.burdelis 3 жыл бұрын

Hi @Phraseblaster, thanks a lot for this video, I've watched it a few times to make the same installation on my console. I was actually about to give up on getting that PPU desoldered and thanks to your video (and your comment on the soldering temperature) I was able to make it!!

@Phraseblaster 3 жыл бұрын

Thanks for your comment! That's great! :-) But you're right, desoldering the PPU wasn't fun. ;-)

@mik_7605 3 жыл бұрын

Thanx for video!!!! I hope my F870ES will be working :)

@megamariofan4009 3 жыл бұрын

I cant find the points to put my temp battery on my Zelda OOT cartridge. How do i do that

@Phraseblaster 3 жыл бұрын

I just had a look inside my (PAL) OOT Cartridge. There are two resistors R1 and R2. You can use their solder points near the battery. R1 is positive and R2 should be negative. If your PCB is different it might be a good idea to trace the track to a different point and check if battery voltage is present there. Assuming the original battery isn't dead.

@jasonclark9462 3 жыл бұрын

What size screwdriver did you use

@Phraseblaster 3 жыл бұрын

I used a Philipps PH0 ( x 60 made by wiha)

@plotskii 3 жыл бұрын

You spin me right round baby right round

@poodudeelite 4 жыл бұрын

Its great there is support for the original famicom, but wow That's a lot of work to have to completely replace the PSU in the process. I ended up using the original PSU with my famicom Twin when these first came out. This video still makes me want to mod my fami though. 😬

@stefhatton2703 4 жыл бұрын

Fantastic video fella , ive just ordered a new Ingo Clock and was kinda dreading this but your video is superb ..im no longer afraid ....could i spray those gears with some Pro Power silicon lubricant as an alternative?

@Phraseblaster 4 жыл бұрын

Thanks! Glad, it helps. :-) I searched for the spray and found: "...effective on plastic gears..." So i think it should be okay.

@mandeygaming7169 4 жыл бұрын

12 years ago 😯

@inigoperezdeisla4657 4 жыл бұрын

I see your speakers are not the stock ones. Which ones are you using? I need replacements in mine. Thaks.

@bjlrr 4 жыл бұрын

Where would the backup power solder points be on an NES cartridge? Thank you.

@Scribblescrabbly 4 жыл бұрын

This video would have been 100% better if you took the time to explain your battery rig and where to temporarily solder them.

@canalretro4152 4 жыл бұрын

Nice video... but how to splint the rom to flash in eprom?

@thomasbarron1615 4 жыл бұрын

Great video I,ve just bought my supplies to do this! Which programmer are you using? I’m using the tl866plus with a AliExpress TSOP adapter

@Phraseblaster 4 жыл бұрын

I'm using the TL866II Plus :-)

@thomasbarron1615 4 жыл бұрын

Phraseblaster sweet!

@gregrable3756 4 жыл бұрын

rgb mod how does it work when you connect it to a new TV with scart input?

@Phraseblaster 4 жыл бұрын

The scart cable is wired to standard scart RGB specs. So any TV with an RGB capable scart input should work.

@gregrable3756 4 жыл бұрын

@@Phraseblaster thank you for the quick reply. so a full hd tv won't have a picture problem?

@Phraseblaster 4 жыл бұрын

@@gregrable3756 If the TV supports RGB over Scart it should work. Sadly most modern TVs don't scale analog inputs very good. If you're looking for the best quality you can use an OSSC or Framemeister for example.

@gregrable3756 4 жыл бұрын

@@Phraseblaster thank you very much! You helped me