Corbett Mower Repair

Пікірлер

@michaelnugara1 10 күн бұрын

So this is the mixture screw adjustment? Thanks for the vid. Much appreciated

@christophercorbett7307 7 күн бұрын

@@michaelnugara1 yes sir...well hidden huh?

@michaelnugara1 3 күн бұрын

I just removed that cap and adjusted it a little, as I needed to use the choke each time to start it even when warm. I gave it a bit more fuel and Problem solved and I thank you for your help.

@christophercorbett7307 3 күн бұрын

@michaelnugara1 good job buddy!!!

@fastalk 11 күн бұрын

It worked to my surprise. Im only getting 9.5 volts while running at the battery. Any suggestions battery looks brand new has a 1.5 year date.

@christophercorbett7307 11 күн бұрын

@@fastalk voltage regulator either bad or lost 12v source to the voltage regulator.

@dpm1964 20 күн бұрын

Thanks. Will try it out. Do you have to replace the welch plug after adjusting the low jet screw?

@christophercorbett7307 20 күн бұрын

@@dpm1964 not at all

@fermore6841 Ай бұрын

Thanks for the video!!

@jesustrevino2023 Ай бұрын

I should’ve watched your video prior to breaking locking tabs on fuel bulb primer. Any suggestions as to where to order replacement part for my Husqvarna 525L? Please advise. Thank you in advance for your assistance and stay the course. ✌🏼

@kevinhinds5410 Ай бұрын

Thanks. That helped a lot

@skipperup Ай бұрын

Thank you!

@kenlowrey5612 2 ай бұрын

Thanks for a nice video. I was trying to figure out how to disconnect the throttle linkage without breaking it. I was on the right track but I wanted to see how someone else removed the link.

@christophercorbett7307 2 ай бұрын

@kenlowrey5612 yeah, no fun when they break

@rey9917 2 ай бұрын

Where can I buy those plugs please

@albertharrell3780 2 ай бұрын

Great job of showing everything you were doing

@12B4Christ 2 ай бұрын

Ok, perfect take down with great info and love the humor. For that exact Mikuni carb, where do we find a replacement needle or overhaul kit for this carb? I dare not attempt the part number for this carb but its something close to Jxx-14101-0x with the vent tube. I know the Mikuni is good so if i can just find the kit or needle, what do you suggest for tracking these parts down?

@6gatornation 2 ай бұрын

do all the gravely pro turn mower have the same bearing size I would like to order the bearing before I take it apart it's a pro turn 52 commercial model 991208

@christophercorbett7307 2 ай бұрын

@@6gatornation I believe the gravely pro master series uses larger bearings than the residential series. The mower here is a gravely/ariens residential mower

@6gatornation 2 ай бұрын

@@christophercorbett7307 ok thank you

@DisgustedGenXr 2 ай бұрын

Nope. I replaced every single thing in my fuel system, new hose, new rollover vent, new gas, new filter, new carburetor, new intake, manifold, gaskets, new carburetor, gaskets checked for cracks. It does exact same thing hasn’t changed a bit.

@christophercorbett7307 2 ай бұрын

@@DisgustedGenXr did you do this adjustment on your new carburetor?

@jjcc2192 2 ай бұрын

You do not have to remove the black plastic piece. Just rotate choke plate towards you and the link can slide right out. Also there is a slot for the kill wire almost directly behind the choke lever. Snap it in or it can wiggle loose from its mounting position.

@christophercorbett7307 2 ай бұрын

@@jjcc2192 cool man thank you for the tips!!

@guadalupemagna4227 2 ай бұрын

Hi thanks for the video is this one turn out low and two and 1/4 for the high apply for all sizes chainsaws .? Thank you

@christophercorbett7307 2 ай бұрын

@@guadalupemagna4227 pretty much

@guadalupemagna4227 2 ай бұрын

@@christophercorbett7307 thank you

@diastoleny 2 ай бұрын

Great advice. Thank you

@carrotcake1955 2 ай бұрын

Very good job. Saved me from taking it to the shop. I’m going to buy some gas in the can tomorrow! Haha. Just a note…you can take the choke linkage loose if you twist silver choke up. It matches and will slip out. I did use needle nose for a light push, but works! Check it.

@christophercorbett7307 2 ай бұрын

@carrotcake1955 thanks for the tip!!

@danieldextre56 3 ай бұрын

Thanks

@christophercorbett7307 3 ай бұрын

@@danieldextre56 absolutely man!!

@Ericbumperpunch 3 ай бұрын

excellent video, thanks!

@christophercorbett7307 3 ай бұрын

@Ericbumperpunch thank you so much my friend!!!

@roberthumphreys1316 3 ай бұрын

I've watched six or eight of these videos on this subject and your's is by far the best of them. My parts are on order and my fingers are crossed. Thanks for the instruction.

@christophercorbett7307 3 ай бұрын

@roberthumphreys1316 absolutely man!!! If you have any issues/questions please feel free to hit me up

@Larry-d3i 3 ай бұрын

I was thinking of putting a kit in the carb I took off, but only if you do a video on it. I don't trust anybody else. I am going to try to replace the carb and lines on an old Poulan Wild Thing 2375, hope to get enough help from youtube videos.

@christophercorbett7307 3 ай бұрын

@Larry-d3i I may have one in the pile. If I do ill do a carb swap on it. Just make sure you make hole in tank bigger so you can run the bigger fuel line.

@Larry-d3i 3 ай бұрын

@@christophercorbett7307 I'm not knocking these other guys doing videos. But what novices like me need is a step by step how to guide like you posted. It's obvious most of them are trying to figure it out as they go. I tried to get ahead of you once in this video, it didn't work and I had to backtrack. I saw a good tip on Amazon on the Chinese carbs. I used a dremel to cut a slot in the needles so they cut be adjusted with a screwdriver. There was no limiter on the one I got. It's doing just fine.

@christophercorbett7307 3 ай бұрын

@Larry-d3i yes sir. They make you have to use these odd ball tools to adjust them. Can never go wrong with a good ol flat head!!

@Larry-d3i 3 ай бұрын

@@christophercorbett7307 I bought a Chinese knock off a few years ago called an X Bull. It's cheap junk, but has some good qualities too. That sucker cold cranks on the first pull real easy with a spring loaded wind up starter and runs strong and smooth. Chain oil leaks, to get to the purge lines you have to take the thing aparr, chain brake won't stay off, choke won'tstay pulled out, but it is a 62cc 18 inch bar and it has never failed me. $130 Vs about 400 for a husky.

@christophercorbett7307 3 ай бұрын

@@Larry-d3i I'd like to check it out

@JamesSuitt-q3z 3 ай бұрын

Thank you for this informative video. I did as you described and it cleared up the idle surge problem on my Kawasaki FR691V. Is it necessary to recover the adjustment screw access after making the adjustment? Thanks again.

@christophercorbett7307 3 ай бұрын

@JamesSuitt-q3z no sir it's not necessary at all. Literally the only reason they put it there is so you can't find the adjustment

@Axel-tk3tk 2 ай бұрын

Hey man! Did you have to knock. Black plastic piece out to get to the adjustment screw?

@christophercorbett7307 2 ай бұрын

@@Axel-tk3tk no sir, just the cap

@trevornaas9676 3 ай бұрын

Been a marine/small engine and millwright for over 30 years one of the best small engine videos I have watched. Very good job!

@christophercorbett7307 3 ай бұрын

@trevornaas9676 thank you so much my man!!! If I could have all that experience of yours now I'd be good to go

@jettramel 3 ай бұрын

Great video, just what I needed, even though its late in the season I'm tired of pulling the plug & priming through the cylinder lol.

@overexposurevideo 3 ай бұрын

I had a hard time getting the the gland nut off, went to a local farm repair shop and paid them € 20,- to do the job ( for all 3 ) . They had a much better torch and a much better spanner wrench to do the job then I did. The rest is a diy job.

@Philjr-h7j 3 ай бұрын

Is the o ring on the carburetor is it a SAE or metric cause my didn't come with one and the used one I got from e bay didn't come with one also

@christophercorbett7307 3 ай бұрын

@Philjr-h7j I don't but it doesn't have to be perfect. Just a snug fit, if you have to use one bigger that's fine

@m-1rlg26 3 ай бұрын

Where did you buy your kits?

@RT668 3 ай бұрын

This is the best repair video I've seen in a while. Very well explained.

@christophercorbett7307 3 ай бұрын

@RT668 man ill take that any day thank you

@nathanallsup1224 3 ай бұрын

How can I set the carb back to stock settings. I just replaced one and I got it all jacked up . I just need to know how to get it back to a good starting point

@christophercorbett7307 3 ай бұрын

@@nathanallsup1224 you need to screw both jets all the way in. Do each jet 1.5 turns out.

3 ай бұрын

Where yu get yur cards at

@DKBrainard 3 ай бұрын

Great video, thanks! “Shazam! Little bitty zip tie.”

@christophercorbett7307 3 ай бұрын

@DKBrainard thank you man!!!

@joshratcliff3065 3 ай бұрын

Thanks a bunch man ,sure appreciate it ,the idle screw did the trick ! I had to remove the jet a blast it with some of that carburetor dope ! Lmao it musta have been clogged up .

@christophercorbett7307 3 ай бұрын

@joshratcliff3065 glad you got it going my friend!!

@Fade2Zero 3 ай бұрын

Greatly appreciated, thanks!

@humbertobetancourt2934 4 ай бұрын

Thanks for the knowledge. God bless you

@ngwamartin8687 4 ай бұрын

I have a problem with mine just starting and gose off in a while

@christophercorbett7307 3 ай бұрын

@@ngwamartin8687 yes sir I understand. That sounds like one you could simply fix by adjust the carb. Turn up the idle screw until chain begins to spin. Then slowly turn out the L screw (one closest to engine) until rpms drop enough for chain to stop spinning.

@pelayoasturias6650 4 ай бұрын

What blue fuel do you recommend? I use Trump Fuel from Ace is that good?

@christophercorbett7307 4 ай бұрын

@@pelayoasturias6650 I use VP can gas

@waylonratcliffe 4 ай бұрын

What is the little black plastic piece on the right side? I broke it off mine and now it’s surging, don’t know if it’s related.

@christophercorbett7307 4 ай бұрын

@@waylonratcliffe you'd have to shoot me a pic or give more details.

@chuckhuff7123 4 ай бұрын

Junk,junk,junk, that cost a whole lot more, morons😅

@malibu7935 4 ай бұрын

What happen if is no primieing or the the gas doesn't stay in the bubble

@christophercorbett7307 4 ай бұрын

@@malibu7935 usually failed check valve. Just put you a new carburetor in and rock on

@malibu7935 4 ай бұрын

Ok thank you very much God bless you and ur family

@christophercorbett7307 4 ай бұрын

@@malibu7935 Right back at you my friend! Jesus sure is good!

@ricksanborn6667 4 ай бұрын

This may be the most helpful video I've seen on KZbin.

@christophercorbett7307 4 ай бұрын

@@ricksanborn6667 well buddy I sure appreciate that!!

@garymercado6707 4 ай бұрын

Was all messed up with the throttle cable until you showed how it fit into the molded piece down below…thanks

@murraywilkins9268 4 ай бұрын

Thanks ,,needed to adjust the screw,,,brand new .mower also.

@christophercorbett7307 4 ай бұрын

@@murraywilkins9268 yeah they come from the factory just not running quite rich enough

@ChosesinWon 4 ай бұрын

Thank you. Your detailed video really helped.

@elong35 4 ай бұрын

This is a great video. The pouring out of gas and replacing with fresh fuel was perfect advice. I did pick up a new carb etc… on Amazon for around $20 just in case and will just save it. Great step by step video!

@christophercorbett7307 4 ай бұрын

@@elong35 thank you buddy!!

@craigkeller 4 ай бұрын

If you’re looking for a vacuum leak, spray bottle with water. Water gets sucked in, runs bad. Easy.

@michaellicholat 4 ай бұрын

Wish I had seen this before a local repair shop soaked me. They replaced the carb and after a few hours the same problem recurred. Thanks for posting this video.

@christophercorbett7307 4 ай бұрын

@@michaellicholat yes sir no problem. New carb plus the adjustment, it'll run better than new. Please consider subscribing. Thank you sir

@fermore6841 Ай бұрын

So what was the issue if you still have the same problem after the nex carb.

@Dboyquicks10 Ай бұрын

Check your gas cans for trash in them

@lancemcwhorter8109 4 ай бұрын

Crazy good video !! Thank you for being a great teacher!!

@christophercorbett7307 4 ай бұрын

@@lancemcwhorter8109 thank you sir! So glad it helped. Please consider subscribing

@Barneysnniper 5 ай бұрын

This worked exactly like you said. I was worried about drilling that out. Sure enough it fixed my idle issue! Hod bless you Sir.

@christophercorbett7307 5 ай бұрын

@@Barneysnniper so glad it helped!!! Please consider subscribing have a blessed day

@DutchieThePromoter 5 ай бұрын

i've got a hustler fastrak with a kawasaki fh580v Kai ... seems to run fine but you engage the blade it doesn't necessarily bog down but it doesn't rev up... but it will bog down and nearly die once u get in grass and ride very slow... New carb etc.. could this be me problem?

@christophercorbett7307 5 ай бұрын

@@DutchieThePromoter sounds like it's only running on one cylinder

@Dieselhorses 5 ай бұрын

I'm surprised you don't have more thumbs up on this video! Worth watching and very informative!

@christophercorbett7307 5 ай бұрын

@@Dieselhorses thanks so much my friend!! Please consider subscribing

@Dieselhorses 5 ай бұрын

@@christophercorbett7307 I did! Changed everything imaginable on a Husky 224L except waiting on the one part I didn’t change-ignition coil. Seems this was a problem with these?

@christophercorbett7307 5 ай бұрын

@@Dieselhorses yes but I have to say I love those machines!!

@Dieselhorses 5 ай бұрын

@@christophercorbett7307 I installed new Harbot carb on Husky 455, changed all hoses, primer bulb, plug. Adjusted high out half turn, but still not wanting to idle and bogs down when squeezing throttle. There were 2 gaskets that came with carb, but the rubber on the intake still looked good. Is there a standard generic starting position for adjusting screws?

@Dieselhorses 5 ай бұрын

Correction, I adjusted LOW side out half turn.

Ең жақсы KZbin

Пікірлер