JK Garage

Пікірлер

@tobyw9573 Ай бұрын

Should check the spindle for play before fiddling with the runout.

@JoeNunya-oz1nd 3 ай бұрын

Thanks for the demo. Also, ignore the comments criticizing the music. I don’t hear so well and I hear you just fine. I’m certainly not distracted by it. 🤷🏽‍♂️👊🏾 A few years ago I owned a large tow behind stump grinder. I used this idea to sharpen the carbide cutters. It worked great.

@Wandrng_drifter 4 ай бұрын

Hey I have a getrag 250 in my garage that does the same thing in 2nd but no noise like it’s in neutral This video and other search results kinda makes me glad I’m going with a g260 in my m52 e34 instead

@BMVaaay 8 ай бұрын

Does anyone know the color code to that orange ?

@closery 9 ай бұрын

Thank you so much for this video 🙏

@ThomasBilt 11 ай бұрын

Was this with a getrag250 behind it?

@JKGarageBMW 11 ай бұрын

No, zf320z

@robertwikeljr-1522 Жыл бұрын

Tungsten welding tips work best when using a "dedicated grinding surface" to avoid contaminants from being embedded in welding tip.

@ALKUKES Жыл бұрын

I got the system that has ac, but my problem is its not blowing in the centre or the door sides, its blowing under feet well and the screen? Any help appreciated thanks

@2secon926 Жыл бұрын

same here, any answers?

@mysraalokbe817 Жыл бұрын

It's been an entire video and you haven't fired up the drill once

@blanky1876 Жыл бұрын

Do you know where I can find new seals and stuff to rebuild these? I checked realoem and found nothing

@johnnybahngload1673 Жыл бұрын

I had a lot of old pipes and rebar to cut up and from what I read kzbin.infoUgkxPDBfLu68o58Aw85O_J-zIFfjJARBhp-3 this would be the tool for the job. Since I had never used one, I watched a couple of youtube videos and I'm so glad I did. Some really good safety tips, which I followed, and this tool did a splendid job. One good thing to know is the weight of the tool puts just about the right amount of pressure on the metal I was cutting, so I didn't have to use a lot of pressure, which is more likely to jam the tool. It made fast work of my job.

@chaseweltzin5853 Жыл бұрын

What’s the blue thing called

@carreteras101 Жыл бұрын

this video is helpful and relevant after 10 years of creating thanks

@SquirrelsForAll Жыл бұрын

Very nicely done and extremely well thought out.

@SquirrelsForAll Жыл бұрын

Really great work, loved the stand. Thanks for creating and sharing.

@Sportyg1960 Жыл бұрын

OMG U I CAN’T say you tried

@paulwaldrop Жыл бұрын

Bought this, from Lowes, 7 years ago. Got a 10% military discount on it. Use it all the time. Just keeps working. Very nice tool, for the price.

@josepeixoto3384 Жыл бұрын

edit: no need for that air setup, just blow on it wow, that radio is still on after 9 years

@cartergingue2793 Жыл бұрын

i have an n26 and i cant find any midpipes only n20 midpipes

@JashanVlogs Жыл бұрын

U can use n20midpipes

@alfredocuomo1546 Жыл бұрын

The greatest killer of drill bits is heat especially M35 & M42 Cobalt drill bits so cutting fluid is critical, granted not a steady flow but at least intermittent reapplication at the very least. Also the type of steel really determines the use & volume of coolant/cutting fluid, hardened, Spring or Stainless steel you should always use cutting fluid.

@crashedking1931 Жыл бұрын

I know this is an old post but how do you stop the coolant from rusting your table and other parts.

@ichbins2545 Жыл бұрын

Sir, I 100 % agree with you. If you don't like wear at your Phillips Tips, take a closer look at PB Swiss Tools, or Wera with the Orange Handle 💫

@gatorwing6231 Жыл бұрын

Great idea. The Harbor Freight 9 Amp Circular Saw Blade Sharpener comes complete with the same diamond wheel plus it has a factory installed eye guard. I stripped off the circular saw holder and it is done. No machining involved. Total price $55. I also purchased the same replacement blade.🤞

@mavericktopgun7564 Жыл бұрын

Good video but loose the music it’s annoying

@stoneyprowell2601 Жыл бұрын

Ware can I buy one of those that you have??

@TJB1510 Жыл бұрын

HIT IT WITH A NYLON BRUSH..?..

@Kraxt0n Жыл бұрын

Were you hearing some kinda "slapping" before any gear left ya? I'm getting some slapping now. Kinda curious to if my smf bolts backed out somehow. As I have a stage 5 6 puck disk installed, and have a new stage 2 (way less aggressive) disk to install. Which is in my BMW 330ci. Getrag 220g... Hoping the best as it's only been manual swapped since August.

@JKGarageBMW Жыл бұрын

No, no noises - this was on a 100% stock m50TU E34 w/ stock Getrag 250 trans. The puck clutches will definitely have a slapping noise while engaging, but other than that you shouldn't have any issues. I was sliding this car and dumped a wheel in a pothole and 2nd gear was just completely gone. I still have the trans to open and see what happened.

@Kraxt0n Жыл бұрын

@@JKGarageBMW yes, I'm aware of the slap when clutch is being engaged. But this is during natural at round 1500rpm. Happens at higher rpm as well. I'm hoping it's the clutch disk warped somehow. As I have a new oem disk. As I can still stomp the throttle down and it'll get. And spin, but I haven really clutch dumped since the noise came about. Shifting is fine as well. So thus my confusion. I suppose I'll know when removed if there's an issue staring me in the face or if it's for sure inside the trans. Found a 330i 5sp wrecked near me for 1,000 us. Dude don't have it listed so, I may purchase for the zf trans and extra goodies it has.

@ringaddict 2 жыл бұрын

The dial gauge you are using, each increment is 0.001 one thou, not 0.0001 one tenth of a thou.. it’s written on the dial face.. >| |< 0.001 inch

@easternarmory7617 2 жыл бұрын

Each tick mark is .001 inches, ie. 1/1000 of an inch, not 1/10,000 as you suggested

@Onizukachan915 2 жыл бұрын

Glad to see it is still running!

@sandise3499 2 жыл бұрын

sick 😀😀😀

@iconicars3050 2 жыл бұрын

Hey Jon. What ecu are you running?

@JKGarageBMW 2 жыл бұрын

Hi! This car is running a DTA S80 Pro

@leecherlarry 2 жыл бұрын

i like the Wiha 40331 (or Wiha 76000 in the US), combined with Felo blades

@zorantb 2 жыл бұрын

Any chance on getting that part 2 of your MPerformance Big Brake Kit video? :D

@michaelhallas6450 2 жыл бұрын

Drill press can do wood and metal . What thickness of metal can this machine drill to ?

@StacheCam 2 жыл бұрын

Miss your videos !

@aceofspades9845 2 жыл бұрын

@pharmdiesel 2 жыл бұрын

Thank You! Love the idea! As a community our exchange of knowledge is the equivalent of peer reviewed journal publications and this ought be the idea. This exchange of ideas is what built up Western Civilization and then spread to the global infrastructure of today. It allows us as individuals (if we are allowed to be that these days) to flourish, be enriched and satisfied. CAN DO and F..CANNOT

@danielallen5181 2 жыл бұрын

Lol

@JKGarageBMW 2 жыл бұрын

;)

@ziggykyndal 2 жыл бұрын

I need to machine the inside of a socett to use to pull sparkplugs from aircraft. Any suggestions?

@keneillawrence2961 2 жыл бұрын

*Bought as a gift for my son and his second grade son to use on a Pinewood Derby car. Wanted something relatively safe and able to be packed away when not in use. Worked well. **MyBest.Tools** Easy to use and set up. Case provides good storage.*

@markproulx1472 2 жыл бұрын

From other videos that I’ve watched, the setup step requires that you index the chuck to a particular slot associated with the desired angle. Is this not the case?

@zorantb 2 жыл бұрын

No part 2?

@professordrmao6321 2 жыл бұрын

I gotta do this to a "popular mechanic socket"

@professordrmao6321 2 жыл бұрын

Better to turn the Williams eBay socket ok Oses to the brand new tool truck socket. Big big price difference

@artyfhartie2269 2 жыл бұрын

I bought an expensive Wiha non contact voltage detector. When I got home, I took a close look at it and saw in very small print barely visible Made in China. Not bloody happy. Ripped off.

@JKGarageBMW 2 жыл бұрын

Was it from a big box store in the US? If so, there is a line of Wiha being distributed that is chinese made and I agree.

@travhurst4167 2 жыл бұрын

Thanks dude

@SK-su5xx 2 жыл бұрын

Wrong way to sharp tangstan

Ең жақсы KZbin

Пікірлер