I appreciate you lmk and happy it eliminated one of those things that drove you crazy. I know how that feels!

No it doesn't. Video was made a long time ago I grow tired of long intros as well as slow to the point videos now a days myself. I enjoy sharing information feels good when others find it informative or of value. Since KZbin demonetized smaller accounts honestly I am less motivated. I would spend the hour or so of my time to shorten the intro and reupload it for future viewers however clicking past the intro is best. In future videos I already plan to lay out any important details in the first 15-30 seconds. I'll check out your channel see what videos you have posted and like and subscribe appropriately. Thanks for the feedback.

Just watched the intro 18 seconds I' can probably cut the intro pretty quick.

Was about to sell my hot tub because of the damn rashes that keep appearing on my skin. Switching over to hydrogen peroxide, hopefully this is a solution to my skin irritation from the chlorine.

​@@JujuPig-vz5mqGood move,now you can enjoy your spa.

maybe you already found it but there is a PCV valve tube upgrade and oil filler cap. PCV Positive Crankcase Ventilation. Condensation develops during temperature swings when its cold i believe that water expands into water vapor. When water turns to steam it expands 1100 times. That is what pushes oil out and leaves the milky residue under your oil filler cap. They want $124 for the stupid kit.

You are welcome. Thank you for the comment as well.

That's what I have going on right now. Uses one wire from 10g 120v wiring works.

I paid 600$ for this lil truck it had 360000 miles on it pushing 500 now. Runs great day put a transfere case in and coils guess I did do the water pump too. 4x4

@@Mavericksa I paid $1200 but only 108,000 miles, I've watched a lot of videos and they seem great.

The blower fan pushes it into heat position. I use a thick wire to keep it in the cool position. Ran it through a hole in the back of the glove box. However your air-condition issue may be something else. Good place to start maybe. My AC doesn't work right now neither does my wife's. Same car. We added freon to hers a while back helped some but then went away. I thinking they both will need a new ac pump. Check power to your switch the flap, make sure you can hear the pump switching on and off by pressing the switch while listen for the "clunk sound" and seeing if the pulley on pump is engaging. Turning.

@@Mavericksa I'm pretty sure it's holding freon, I put a gauge on it and it read on the lower end (but still in the green), then went off the chart. I think it's bc the compressor is kicking on and off because it's low, not sure. There's something goofy about the ac on these cars. It used to work, then it didn't. But when I switch from cold to hot it makes no sound so I'm pretty sure the blend door actuator isn't working. I will check the fuses too, since that also seems to be an issue...if the front two fans aren't running the ac won't work right.

I know my video here is not the best however the area where I'm working has the potential to arc from wires that have loosened over time. I would start by inspecting he wire here. Imo.

Should I change the brushes?

@@ronnieferguson8781 if the motor has been used a lot over the years it may need new brushes . You can take a look while you have the back off. Failed brushes may cause the breaker trip. If the motor turns a little before it trips the breaker would indicate the brushes have some life still.

What the thing you hate the most? The jamming or glossy labels failing to load properly then printing a half of sheet before error ing. That last ones my biggest complaint.

Glad to hear it. These vacumes suck.. in a good way. I think the electrical hose connector area finally took ours out.

What's up brother!

No thanks needed for nothing please sarcsim rarely helps What are you stuck on?

The clips are sort of like your wife or girlfriends or a woman's bra . You need to pull the fabric down toward where it's attached enough to the away from the frame. Hard to explain.

Your welcome I'm glad you found it useful. My internal dialog prevents me from uploading sometimes. With this video I said their has to be somebody out there right now freezing cold and if it helps one person its worth it! I would love to have you as a subscriber. Its free. I have a video on doing the front wheel bearings on this truck not yet uploaded. Germans make great bearings but we (wife) had a little incident a couple winters ago into a small ravine and creek that caused premature failure.

You checked the water right? Simple however I never knew untill I knew about the water heats up from the engine then the thermostat opens which then allows hot water to circulate and flow into the heater core. Heater core is located roughly where the aviators is and is basically a small radiator with a blower that blows through this small radiator (heater core) and into the vents etc. Heater core can become clogged with rust, themstats can rust closed, make sure you have water. ..... ??

You can't really have too much. You want it to be at minimum 100 ppm concentration. I like to run it closer to 200 + personally.

Just cold air.

I have to say I love hearing that. This was one of the first videos I shared my parents handed down this vacuum and they mentioned how long they tried to access the belt and could not figure it out. They had the neighbors over one night all working on it. I love finding solutions so this was a welcomed little challenge. Soon as I got it I wanted to share it even if it only helped one person. Seemed kind of silly too but glad it helped and thank you for your kind words. If you feel like subscribing that would be awesome. Every since KZbin changed its policy and stopped sharing ad revenue in be been I little less motivated to upload. Looking for a 1000 subs! Thx.

@@Mavericksa I subbed last evening! I will get my kids to sub too to try to get you to your goal!

www.hydrogen2o2.com/product/25-hydrogen-peroxide-test-strips-400ppm/

Sometimes i forget that others may not know how yet. I usually only do short videos high lighting the crux of the project. I bet you tore into it and got her going. I hope you did and I work on being a bit more considerate and see if I can get you a bit further if you give me another chance. Thx

Don't have this bad boy anymore however. So... Got anything else we can fix?

@amy kelly

I actually was not able to fix it because a part had broken off on the roller. But thanks for your reply.

Im happy to hear my videos are helping people find hidden screws easier and quicker in this busy day and age.

www.hydrogen2o2.com/product/6-gallons-35-spa-science-hydrogen-peroxide/

or LA Salt Co.

www.hydrogen2o2.com/product/2-35-spa-science-hydrogen-peroxide/

www.hydrogen2o2.com/

or LA Salt Co.

or LA Salt Co

It is not the bag I replace it frequently

Forgot to mention that it was a different style board but same issue and was easy to see where the imprinted circuit failed.

Awesome. Glad you found the information of value and I appreciate you lmk. i have tons of this type of information however since google stopped kicking down $ for those with less than 1000 subs i have not been that inspired to upload content for them to sell. those lights are handy.

Sometimes a little piece of paper may still be in the machine if any ripped. Inspect for that and then Make sure all the doors are latched closed.