Ahoj prosim ta kolko percent musí mať tá kyselina aby oddelila zlato? a čo si potom nato nalial ked si to dal von z kyseliny?
@BohumilGraman5 күн бұрын
V podstatě je to jedno, jen když je slabší, trvá to déle. A co jsem to nalil? :-) Nevím, dej čas, ale pokaždé to tam píšu :-)
@DK-ze8mq4 күн бұрын
@@BohumilGraman Díky za odpoved na kyselinu a to čo si nalial som myslel od času 3:10 ten AR solution že čo to je :D dakujem
@BohumilGraman4 күн бұрын
@@DK-ze8mq To je Aqua Regia, neboli Lučavka královská. Tedy směs Kyseliny chlorovodíkové (HCL) a dusičné (HNO3), nejčastěji v poměru 3:1.
@DK-ze8mq3 күн бұрын
@@BohumilGraman ok diky za odpoved :)
@omarnail62406 күн бұрын
You did not mention the methods, and this is a negative point. Did you use nitric acid first or aqua regia?
@BohumilGraman6 күн бұрын
I mentioned it, it's clearly described in the video.
@jasonteem991715 күн бұрын
So you got like 10 dollars worth of silver for all that?
@BohumilGraman15 күн бұрын
How did you calculate that??? 😀 I mined 153 grams of silver, you think a gram of silver is worth six and a half cents?
@TechTrashCash20 күн бұрын
Can't stress this enough, wear an N95 or even a respirator while breaking these plastic connectors apart. The amount of dust and environmental contaminates these computer fans ingest and deposit on these things cannot be at all good to breathe in. Thanks for the video
@marcelopizzutipes2695Ай бұрын
Hello! I noticed that your solution has tin slag after dissolving pins that were not previously cleaned for tin with nitric acid. I usually have problems with this if I do not remove the tin, which makes it difficult to filter the solution. Do you have any ideas on how to avoid this?
@BohumilGramanАй бұрын
See this: kzbin.info/www/bejne/iJrIfn1uq9Okos0
@bbbgun4882 ай бұрын
Add any acid to the water?
@BohumilGraman2 ай бұрын
When?
@bbbgun4882 ай бұрын
At the video point 3:41
@bbbgun4882 ай бұрын
Once the reactions are complete, dilute the solution with water in a 1: 1 ratio. !VERY CAREFULLY! add the acid to the water. The reaction is STRONGLY EXOTHERMIC.
@bbbgun4882 ай бұрын
Add any acid to the water?
@bbbgun4882 ай бұрын
I want to know more acid names
@salema212 ай бұрын
What is this product thrown in at the end to extract the gold! Denox? I couldn't find it
Wouldn't it be better to just use HCl to remove the solder?
@BohumilGraman2 ай бұрын
No :-)
@dfuller34472 ай бұрын
What was the percent solution your acids?
@dannysearcy33733 ай бұрын
Best videos I've come across yet
@Boleh-k7r3 ай бұрын
Ijin download
@sahinsenel8523 ай бұрын
Wie lange soll bleiben denn Silber so lösen kann? Gruß Senel
@abnnuzzinicholasclay6863 ай бұрын
Click bait he said 1000 grams and it was 999 grams. Where is the government fact check ? We need more people to tell us what it is before I loose my miiinnnddddd
@ΛεοΠουλιαν3 ай бұрын
Hello sir..great video...i have a question please...for the 11 gr of material how much dmg powder we must use? I took a n old tesla telephone center...thank you very much for your videos...
@edwardmicoo49253 ай бұрын
It won't hurt yuh
@edwardmicoo49253 ай бұрын
Don't neglect to filter between rinses
@bakulonline-jv2xd3 ай бұрын
Which type of citric acid is this, sir? for food or for cleaning ceramics? does it have to be 1g for the dose? If there is too much citric acid, for example 1.1g, will the concoction not work well, sir? I really need your method to remove tin and be able to extract the gold in the tin!!
@orange-dd5rw4 ай бұрын
total chemicals used by liter list plz mister Bohmil Graman
@sashabelik93034 ай бұрын
Спробуй перед плавкою стиснути осад в брекет ! За допомогою 2 поршнів від шприца вставлених в один корпус !
@aberagebretsadik40405 ай бұрын
Thank you sir ! I got good study !!
@PardeepSingh-sx9fw5 ай бұрын
Nice yield and very informative video. One question remain what material is used for denox?
@ricardocrivellari10856 ай бұрын
Mentiroso
@8bitrainbowdash6 ай бұрын
Damn, I wish I could do this at home, have a bunch of cpus and work at a electronics scrap place, but I do not have the rom for the fumes or risks.
@radiocomponent6 ай бұрын
Sodium pyrosulfite (Na2S2O5) stimulates the development of allergic reactions and causes diseases of the gastrointestinal tract. Releases toxic gas on contact with acids. If in contact with eyes, may cause eye damage. But this does not prevent this chemical compound from not only releasing gold from solution, but also being a food additive E223. Пиросульфит натрия (Na2S2O5) стимулирует развитие аллергических реакций, вызывает заболевания желудочно-кишечного тракта. При контакте с кислотами выделяет токсичный газ. При попадании в глаза может вызвать повреждение глаз. Но это не мешает этому химическому соединению не только выделить золото из раствора, но и быть пищевой добавкой Е223.
@РусланБабух-ю2м6 ай бұрын
Лайк тебе и подписка 👍🔥
@SunRabbit6 ай бұрын
Podle mne jste nedostal vsechno Stribro hned pri prvnim postupu. Na tech folii nema spravne zustat nic krome nepatrnyho a pruhlednyho stinu tech puvodnich nanosu. Ja jsem videl video kdysi davno kde pouzival varici kyselinu dusicnou aby docilil prave toto. Mimo jiny, KDE jste sehnal dusicnou? Ja mam folie z asi 1000 klavesnic (bedna asi 60 x 40 x 40) a ja asi to cely spalim, pak odstranim ten popel s tetrachlorem, pak to vyredukuju elektrolyticky. Jeste se ale musim poradit s jednim profesorem chemie ohledne nejlepsiho postupu.
@YourDailyVideoNews6 ай бұрын
Great video ‼️‼️
@coinkiller54956 ай бұрын
And it will go green and you can reuse it time and time again if slowdowns just add some more HC it will go dark green and put all kinds of boards in with gold flashing on it floats of and strain gold off and do it again and again put gold fingers in and over night gold floats of copper chloride two it’s called
@coinkiller54956 ай бұрын
AP is hydrochloric acid and food grade peroxide for shop put 50 mill in 2 litres of hc
@YourDailyVideoNews6 ай бұрын
Cool Video - please do more 👍👍👍
@IsmetBiljali-vg4hu7 ай бұрын
Perfect
@IsmetBiljali-vg4hu7 ай бұрын
Very nice work
@andrebattis94107 ай бұрын
Good job
@andrebattis94107 ай бұрын
Second AR you should added sulfuric acid to dissolve tin or lead
@patrick81987 ай бұрын
24k pure nice gold ❤😂
@patrick81987 ай бұрын
Wow!👀🤩….. That is a nice lick👅❤️😂
@vanquynguyen82987 ай бұрын
Hơn 1 kg các chân mạ vàng này ta thu được 6,5 g vàng , cũng nhiều hơn so với lượng vàng có trong IC thông thường ( không kể những con chip máy tính ) ?
@patrickwilliams46137 ай бұрын
Nice video good job
@knowldedge50127 ай бұрын
how do you separate capacitors from the pins?
@okboomer62018 ай бұрын
Next time talk a bit so we know WTF you are doing
@ScienceInspiration-ot1le8 ай бұрын
Hello can i know whats mean denox mean .if use any chemical for denox
@goldandsilverminingintheci89428 ай бұрын
I once did a small moving job for a handful of gold crowns. Worked for me!
@coinkiller54959 ай бұрын
One thing bro you had to denox?? How much nitric did you use?? If you start with few mills at a time on heat and with lid on reaction stops put few more mills in until it’s resolved and the more legs you remove before you start you will use less nitric because copper takes a lot of nitric and the more copper you need more liquid to dissolve the salts in but good job we’re is the water for SMB you drop gold you need double solution water???????
@coinkiller54959 ай бұрын
Hi moose coin killer from Australia here what I do with my chips first is I put in AP for few weeks or so and it eats all the magnetics out of the chips all the way up and inside 85% so less to eat away with expensive nitric great video should try it out and make a video on it
@YourDailyVideoNews6 ай бұрын
What is AP ?
@NanamiKairyu9 ай бұрын
sulfic acid should be like 96% atleast 86 will not work actually(only little bit). It's long time taking, dangerous, also usage of acid is high. Only one bonus that gold not lost in the process like you can do when burning.
@김한준-y1d9 ай бұрын
I think too much that the gold and pal from 7.5g (0.2g and 0.44?)
@lukasrosko14809 ай бұрын
Chapem to spravne 200g pinou a jeden g zlata ? Cca 30e +- ?
@ezatsheshtawy97669 ай бұрын
Excellent ❤ nice time
@otorejthar347410 ай бұрын
Hi Bohumil,I have question. How long did you soak the plates for? In your first step
@BohumilGraman10 ай бұрын
Until all the metals are etched away.
@otorejthar347410 ай бұрын
How I can you contact (pm)? FB or something. I need your help
@otorejthar34749 ай бұрын
How I can contact you private? Can you give me email? I have any more questions.
@henrykmielczarek318910 ай бұрын
Jaki sens ważyć z metalem w 0,55 min.
@BohumilGraman10 ай бұрын
Abych měl alespoň přibližnou představu, kolik HNO3 budu potřebovat.