Andy Maverick

Пікірлер

@samgolden4921 14 сағат бұрын

I would leave ur disk n a cd sleeve n the case.

@rezistentlaconsiliere146 15 сағат бұрын

Excuse me...wich were the symptoms? Thanks!

@naderkaddoura8588 5 күн бұрын

Personally I find the clones somehow better in terms of button longevity.Original Sony ps2 controllers have film contacts that once fail cant be repaired. I prefer clones.Just my opinion for ps2 controllers only.

@randallfallin1423 12 күн бұрын

You'll also need to find a video on removing stripped screws, especially if you've already done this lol

@SuperHamlet666 15 күн бұрын

I’m about to try replacing my thermal paste after using cleaned my heat sink and my ps4 shuts off every time I load a game. Any thoughts on this?

@ele_112 18 күн бұрын

Make sure you change the coin battery while your in there you can see it at the bottom of the board at 5:47.

@killerking2346 21 күн бұрын

What screwdriver is that?

@Ahmed-bi3ye 21 күн бұрын

Can i take the mother board out to replace the rhermal paste without opening the other side like the power supply and the other stuff? Because i have one of the power supply screw stuck i couldn’t open it

@sandorcsata9687 29 күн бұрын

Hi, Can you tell me whatis the internal diameter of the tube you used to take out the fuel pump house? Can it that was about 140 mm?

@andymaverick 28 күн бұрын

Hi. Sure, it was a 150mm, theoretically a 140mm one would also work. Mine was a little bit loose but a 140 seems quite snug.

@sandorcsata9687 28 күн бұрын

Thanks a lot.

@annamariapoelmann2611 Ай бұрын

I have recently acquired a Bernina Jubilae, but without the electric cord, or . There is no “hole” to plug in a knee handle. Does anyone know if a foot pedal would go with this model?

@andymaverick Ай бұрын

What model do you have? Later models had foot pedals.

@reyrrz Ай бұрын

Was it hard to put the locking ring?

@andymaverick Ай бұрын

Not really, aligning it is the hardest part.

@reyrrz Ай бұрын

I’m having a hard time twisting it, is crazy, I’ve been 30 minutes just trying to align and twist, I’m even thinking I got the wrong ring.

@andymaverick Ай бұрын

If It's aligned properly then you have to push down on it and twist it while doing it. First try twisting it anti clockwise to find where it "bites". When your at that point you just turn it clockwise. If you have someone there then ask them to push it down, its better that way.

@LudusAurea Ай бұрын

Most of this is unnecessary. Clorox wipe, alcohol wipes, jobs done - no more adhesive, sticker, or germs.

@andymaverick Ай бұрын

Never tried Clorox wipes, will give it a go. Thanks

@wellingtonalves1774 Ай бұрын

Very cool video! Thank you for taking your time to explain everything 👍🏼

@andymaverick Ай бұрын

Your welcome, I'm glad you liked it!

@martinward691 Ай бұрын

This TV is amazing. Games play so well on it. Best ever. It actually makes me better at games because they play so well on it. And the sound is like an arcade. Impressive. (Snes)

@andymaverick Ай бұрын

I'm glad to hear it, how long did you have yours?

@benmassi8333 2 ай бұрын

Thank you for the video you are the only one that really shows how to fix this crap.

@andymaverick Ай бұрын

Your welcome, I'm glad it was helpful.

@薬師シャルル 2 ай бұрын

awesome，but how it felling，does it better in games or just rude rumble

@andymaverick Ай бұрын

Its not perfect by any means. I Think its too strong and not optimesed. I'm thinking ways of fixing it. I hope that xbox releases the offical one soon.

@theMF69 2 ай бұрын

Great video, no unnecessary music, clear and straight to the point 👍

@andymaverick 2 ай бұрын

Thank you, I'm glad you liked it.

@jb14ops Ай бұрын

@@andymaverick I have fix my ps4 and re-applied thermal paste but my problem is once I try to start a game the screen goes static and then the ps4 shuts off black screen dead! I try to press the button but it doesnt work and I have to re-plug the power cord to turn it back on.

@Lucas-Amaterasu 2 ай бұрын

I recently found the same TV at a thrift store in Canada. Mine looks almost identical, but it's a Chinese version (with the model number of "LCD14E1A"). It has two AV inputs (with one being an optional output), one composite input, and one s-video input. It also has the same handle and kickstand on the back as yours. Something to note is that it has much better viewing angles than other early LCD TVs and monitors, in my experience. I'm using mine with a modded Nintendo Wii.

@andymaverick 2 ай бұрын

You're right I didn't even noticed the view angeles, had to check just now. I'm happy to hear that you found one, and you seem to be satisfied with it.

@pauljacob99 2 ай бұрын

You lost me at “use razor blade.”

@gamesstation607 2 ай бұрын

ooooooooooooooooooooooooooo. soni

@RealestKhalil 2 ай бұрын

Even though I’m late to seeing this video I’m glad that we have similar ways of cleaning games. I wasn’t always cleaning games. I used to just leave them as is but about a year ago started to focus on making them look like new. It’s amazing what can be accomplished with patience. Unfortunately if cover art is water damage there is no way of bringing it back I had a few damage artworks in the past I ended up swapping them out for better ones. That’s the only thing I would say that I don’t have information on far as making it look like new if it’s even possible. I’m glad that I’m not the only person that likes to take care of my games & make them look like new completely. Thanks for making the video! Peace and love

@andymaverick 2 ай бұрын

You're welcome and thank you for the kind words, I'm happy to hear that you enjoyed the video. Water damage is a tough. To my knowledge there is no other method besides that you just said. I tried soaking them with minimal water than I used flatiron trough a cotton fabric. The outcome is not perfect, best option is to get a replacement like you just said.

@RealestKhalil 2 ай бұрын

@@andymaverick you’re welcome and yeah, I tried the flat iron trick. It didn’t really help much unfortunately.

@Sandrinilango 2 ай бұрын

Thank you!!!

@andymaverick 2 ай бұрын

You're welcome!

@ptaylor81 2 ай бұрын

WD40 works for me to get old glue off

@KimMerta 2 ай бұрын

Yeah i learned about that some time ago, oil in general works.

@andymaverick 2 ай бұрын

I didn't know, will try it next time. Thank you for the info.

@Disaster_Circus 3 ай бұрын

Dude I've worked on a LOT of computers and consoles and i swear the thermal paste on the Xbox 360 was the hardest to remove out of anything I've ever worked on.

@andymaverick 2 ай бұрын

Your right, did you worked on the original xbox too? The thermal paste on those is even worse.

@nenoroalzafen30 3 ай бұрын

Those stickers were paid actors It's rare i remove one without leaving the glue on the case 😭

@andymaverick 2 ай бұрын

I chuckled😆. From time to time I find some stickers that are pain in the... belive me.

@richadjimenez4017 3 ай бұрын

Is the 3yk same as 3YJ what is the different ?

@andymaverick 3 ай бұрын

@@richadjimenez4017 The frame is almost the same. The main differnce is in the front fork and the cowling for the handlebar. The 3YJ has drum brakes in the front and the 3YK has disk brakes in the front.

@lukasgyudinec1293 3 ай бұрын

what is the diameter of the pipe?

@andymaverick 3 ай бұрын

8mm if I remember correctly

@sapphy2 3 ай бұрын

I thought I could easily get to starter electrics hoping to find a loose connection. But I can't find way into electrical connection parts

@andymaverick 3 ай бұрын

I would check the switch first, it can be oxidized.

@sapphy2 3 ай бұрын

I have a very old Bernini which suddenly will not switch off. Mid use.

@andymaverick 3 ай бұрын

It sounds strange, what model you have?

@MadastheHatter13 3 ай бұрын

Ive got a game with a sticker attached to the actual front artwork... And another one with a sticker attached to the manual... Anything I can do?

@andymaverick 3 ай бұрын

I tried tackling these before with little to no luck. I would not recommend messing with them for now. I tried freezing them off before but that left the glue on the artwork.

@LPaudaxviator 4 ай бұрын

This instantly fixed my issue. Thank you so much!

@andymaverick 4 ай бұрын

Glad it was useful, you're welcome.

@CheesusSweet 4 ай бұрын

I have some indentations left over from where I've peeled stickers off. Will these go away over time? Or am I going to need a replacement case?

@andymaverick 3 ай бұрын

You can try empting out the case than use a hair drier on it. It will not go away completely.

@anterometso276 4 ай бұрын

Hello. I am looking for the location of fuel pump relay / fuse. There is no fuel pump sound when I turn the power on. I have 1.4 hatchback 16V pre-facelift, fuel pump does not have a return line. I had another one, also without return line from 1.6, so there are probably different versions. I connected it (I had no "special tool', I could not remove the old unit like in the video), still no fuel pump sound when power is on. I am not 100% sure, but I suppose the second fuel pump should work, so for some reason the fuel pump does not get power. I also can't find the location of fuel filter, it is not where it is supposed to be in this video, I can't find it. I get "check ignition" message, engine rotates, does not start and I believe it is a fuel problem.

@andymaverick 4 ай бұрын

Hy. I checkd before and I never found a fuel pump fuse/relay in the car. I'm not sure but I think that its integrated inside the ECU. I think all of them have returnless fuel systems and only have one fuel pump. If you connected your fuel system directly to a 12v battery and there is no sound it's probably has a faulty fuel pump. I never worked on a 1.4 hatchback but try to trace down the fuel lines, there should be a filter somewhere. I think your problem is different, If I where you I would check the top dead center sensor on top of your gearbox next to the side of the engine block. Take it off and clean it first and check the connection, once It made the same symptoms for me.

@oze-bikes4life663 4 ай бұрын

100% pure Eucalyptus Oil is more effective than Isopropyl Alchohol for removal of Sticker residue on Disk Covers.

@andymaverick 4 ай бұрын

Never heard of it, I will give it a try. Thank you for the information.

@oze-bikes4life663 4 ай бұрын

Thanks for the upload, a good video... cheers 🍻

@OgashediTv 4 ай бұрын

Hi my ps4 pro got struck by lightning ⚡ could power pack possibly be damaged?

@andymaverick 4 ай бұрын

If it does nothing when you plug it in then most likely your power supply went bad.

@sullysuvann1380 4 ай бұрын

Had too use butt of a screw driver to hammer the x brackets 😢

@andymaverick 4 ай бұрын

It was that hard to get it back on?

@raymondwong4645 4 ай бұрын

Very interesting, Xbox definitely need to replace the old ERM with the LRA, just wondering how are they going to change the wave format to achieve immersive haptic effects. Signal format will be quite different. Same for the trigger, can be replaced by 2 small LRAs.

@andymaverick 4 ай бұрын

You're right, they have to change all that to be left with a basic haptic effect on most games. I'm curious to see how many games will make use of it and support it in the long run.

@TucBroder 5 ай бұрын

Should you use Isopropyl alcohol when cleaning the case with the cuetips?

@andymaverick 4 ай бұрын

It wont hurt, that is good for removing any left over grime.

@Playvoodoo 5 ай бұрын

My PlayStation stops at PS logo screen, tried potentiometer tweak, some games load, some don’t.

@andymaverick 4 ай бұрын

Sometimes this happens with the playstations I work on. I usually change the laser for a used good one or I buy an aftermarket one when this is the case.

@serggurkov7559 5 ай бұрын

Hi dude. First of all - you are awesome!! And now to the point. Did you try to connect haptic motors not to the rumble motors soldering area, but to the audio socket?

@andymaverick 5 ай бұрын

Hy. Honestly, it never crossed my mind before. I can do it in a shorter video in the near future. Thank you for the kind words and idea!

@MihaiStreames 5 ай бұрын

Such a great guide, I cleaned up some of the worst games right after this and the difference was insane

@andymaverick 5 ай бұрын

I can imagine, people tend to look over these things. Thanks for the feedback, I'm happy that my video was useful.

@ricicloriparazionimr.g 6 ай бұрын

Great! thank you very much 🙏

@andymaverick 6 ай бұрын

You're welcome, I'm glad my video was usefoul!

@ricicloriparazionimr.g 6 ай бұрын

@@andymaverick yes 🙏💪 greetings to Italy 🇮🇹

@eibes 6 ай бұрын

Well done ! I just saw one this morning with the same problems at the ressourcerie. I was strong, I didn't buy it ! I already have a Bernina 700 and several Singer, my wife would kill me ;)

@andymaverick 6 ай бұрын

You have a strong will! It's always nice to hear about other peoples collection :) . I think these problems develop when they dont use the sewing machine for years or decades. Anyway, thank you for the kind words and good luck with your existing projects ;).

@brad6619 6 ай бұрын

Damn bro that is way too much thermal paste

@LuchezaRStoineV 6 ай бұрын

2:55 I was scared for your finger close to the blade 🤣 anyway thanks for the video I cleaned before second hand games that I got but now I will ''deep'' clean them so they look even better

@andymaverick 6 ай бұрын

Thank you for your concern😅, watching it back gives me the chills. You're welcome, I hope the games come out great.

@LuchezaRStoineV 6 ай бұрын

@@andymaverick yeah they came out pretty good not like a brand new game but better than just wiped with wet wipes. Stickers, dirt inside the case, dust under the transparent protection for the cover art all gone. I didn't had alcohol so I used sanitizer as you said and it works.

@Blastermaster113 6 ай бұрын

bro ive never thought about usig a raser blade. i always used my nails

@andymaverick 6 ай бұрын

We learn something new every day, I'm glad I could help. By the way, I used my nails before but it didn't work out for me.

@ceydarus 6 ай бұрын

I need this mchine hw can i get

@andymaverick 6 ай бұрын

This was a local Facebook Markatplace find for me. I'm not sure how rare this is.

@Whoisjase 6 ай бұрын

This is an amazing video, bro. You just need a little background music. Add that and you’ll have a very engaging format.

@andymaverick 6 ай бұрын

Thank you for the kind words. I will add it in part 2, It's hard to choose music what is good and not copyrighted. There were a lots of good ideas from the viewers so I want to try them and I will search for some music.

@jorgerivera5003 6 ай бұрын

After months of search, somehow I got a copy of FF7 Remake Integrade for PS5. The case is like-new, but the plastic outside was a bit dirty. Thank you for the video

@andymaverick 6 ай бұрын

I didn't know that it was that hard to come by, your lucky. I'm glad I could help!

@Gabriel-oj5db 6 ай бұрын

Great Work 👍👍👍

@andymaverick 6 ай бұрын

Thank you!

Ең жақсы KZbin

Пікірлер