Nice!

Are those Rota's with wheel spacers? 20mm or 15mm. Looks good flush. Good work!!

So Jelly! Came out Amazing man, good job

Junkyard civic cool ok i keep follow you channel KZbin ok bro

Junkyard civic ok

Salvage/junk yard junkyard eg hatch i follow you channel KZbin ok

How's the results looking now?

Also do you have the torque specs for the drivers top mount?

Your video is way better than all the other ones I’ve seen thanks for being detailed!

Dude I forgot how the thing was positioned under the 10mm, thanks so much

It's in the fuel tank, lol

Where do you order that part?

Thanks for this video i have a 99 stb with similar problem. I hope this solution works on for me. Thanks 🇰🇪

Great video and thank you for showing the bolts on the fire wall it helped out a lot

No sound?

Song name???......its a sick riff

How many solenoids are there and where did you buy it?

thank you! video is very helpful to replace the ones on my CRV volume kind of low hard to hear

Wish it wasn't in fast motion

Did you charge the system yourself? If so how much pag oil did you add?

Outer end of bushing you just changed is not bolted in. Hope you fixed that.

Thanks my man ❤

umm Ummm ummm umm

How did you get the crown done additionally bro? They told me they can only do my front or crown

How long you were in Thailand for this procedure?

How many grafts?

Good job bro it's hard to find anything on for information the 01-03 cl. I usually use the dealer diagrams so I don't have but a shop manual for everything

Dude! Thank you 😊 that was an awesome video. I'm removing this trans and this is the last thing I needed to remove lol hope I didn't screw up my cable 🙃 I thought it unscrewed 😮

Going to the same place in 2 days mate thanks for the video!

is there one on each side? left and right side of the vehicle?

Very helpful. Music was distracting

I scoured youtube for this information and there are only two videos showing how to remove the door. Depends on which year CRV but here are your steps: Remove door panel unplug the main harness and then remove bolts . Easiest way is to remove 1 bolt from each hinge, ( make sure you have something or someone holding the door ) then personally I always remove the top hinge 1st then bottom. Reverse steps are the same. Shouldn't take more than 20 minutes for each door

Almost bought the same ones. Thanks for sharing man!

Useful video and much better chisel job than I watched on the video I clicked before this. Trying to diagnose my own issues with rpm and car rough starting after running temperature. But ultimately, my car is 24 years old now, and I'm sure a lot of those parts and gaskets are needing replaced..

So hard to find how to videos on these. Thank you!

the allen screws thats holding down the cover what size? ive tried the last 2 sizes and didnt fit

This video is the worst!! You cut out the hardest part of the entire project!! I tried doing this stupid scooter tire for 2 hours now and have gotten nowhere, these scooters suck and I’m just going to ride a bike instead. This video is the reason I don’t sleep at night and I want to just go out side and walk because it would take me faster to go places than to spend 10 hours on this stupid tire!!!

Muy bien explicado

2024, bout todo this in my lawn so my boss doesn’t see the car he let me borrow is leaking fluid 😂

Hey man. Appreciate the Vid. My lady was hit at a 4 way intersection last night. I’m headed to the Pick n Pull tomorrow out here in Lakewood , WA. Hopefully they have a white door!! 😎

You still got this?

I changed my rear tire and I tried putting it back on the scooter but the wheel doesn’t wanna go in place do you know what is going on ?

Hello, when I removed the cover, a small spring coil and a tiny washer without hole drop on the floor. Do you know where it goes?

Hi, Do I have to put it in Neutral? Edit: never mind, I realized you mentioned this important step at the end. All the other videos I found don’t mention this step. Thanks again

Im trying to find a video on replacing the knock sensor

Excellent video.

You need to talk step by step saying what you're doing..... Keep talking keep communicating the whole way through....👎👎👎

How long did it take?

Thanks for this video man 👍🏽

Great video, watched a few times before I headed out to do it and the install went super smooth. For anyone wondering here’s some tips: -Ramps will give you plenty of room -Use PB blaster ~5 minutes on the sensor and it’ll come off pretty easy -02 Sensor socket is a must (22mm I believe but I’ve heard 7/8 works, just make sure not to round it off) -Do a favor for whoever will have to change the sensor next and use some copper anti-seize on the 02 sensor threads before the install but make sure to not get it on the sensor itself -it’s definitely doable to pop off the sensor clip from under the car with one hand, you can practice on the bank 2 sensor 1 A/F sensor as it’s easily accessible from the engine bay -Disconnect the negative terminal on the battery any time you’re working with sensors -Make sure the exhaust is cool to the touch before you work on it