Great video, thx!

Thanks for the video I don't feel I need fluro for stealth , which is why I didn't want to put it on my main line , I know people can catch braid direct But I realised that fish have teeth and they may end up cutting and fraying the braid so that's what taught me to put it on in the end I've seen people's lures come off and they're lures snap and they lost money , lures and fish which made me want to fish braid direct So I need a good Knott , thanks for your time making this video, much appreciated

Why is it so easy on the simrad app

Man, Garmin is way better with one click.

Thank you please show me how to loop knot for The jig how to retrieve retrieve the jigs thank you this is Oliver thanks again

Thank you Sir

The Tidewater guy is horrible! He acts like he’s on meth! Could he possibly say ok more times…

Impossible. Never works for me. What other options do I have?

I still can't figure out this knot. Definitely the hardest knot I've ever tried.

Geez that takes forever to build out the new route. Once it’s saved as a route does it take it long to pull it back up?

I would like to know how thick is hull on tidewaters? Mine came with bilge pump screwed into the floor. Can that cause water damage? How thick is the bottom? Ty

This doesn’t work, I’ve tied it exactly how he shows over 8 times now and every single time it pulls through

Makes so much sense! I hated the FG knot because of the supposed required tension and I did in fact lose some fish to a knot that slipped as well as when I was cinching it down during the tying process. I'll practice your method and maybe I'll start using the FG again; I've done well with the Alberto knot and haven't lost a fish yet. hmmmmm, decisions decisions. Thanx for a great demo!!

Thank you man perfect 🎉❤❤

I will never subscribe to your channel, Or anyone elses for that matter, If there is annoying as hell, Music playing!!

Great video, all information and no nonsense! Appreciate you taking the time to make it and sharing it!

Can i use it in Direct sunlight ?

Dont sand with finger..

Can you tell me what the issue was that caused this repair? My port side pole is opening up a bit going down the river on its own. Not sure if this is related.

Just some more feedback. Hooked up on a good sized striper in the surf. While reeling it in, an approximately 800-1000lb Grey Seal went after my fish. I knew i was going to lose the fish, but all i wanted was my lure back. After fighting the seal for awhile my mono knot to the lure let go. The FG Knot, however, held through the whole process.. obviously, this knot will hold.. Thanks again..

👍

Do you worry about the scratches from loading the boat or do you leave them as its kinda unavoidable.

halfanus tour. then a lot of nonsense at the end.

Looking to buy my first boat. Love that you shared your facility with us. Great to see the employees and the pride taken in building each boat. I really appreciate the detail you showed in the process of building each boat. Helped me make my mind up on the 1910 Bay Max.

If my boats not getting all the blood and guts or crazy bad, can I just wash the deck with the boat cleaner? Not having to clean it with deck cleaner? I think after washing with deck cleaner, you have to put some wax back on?

How do I get my Simrad to look like the Navionics app? Installed card and switched to Navionics chip on my Simrad and it still looks the same. Been using my phone cause I can’t figure it out. Thanks!

What of oil is used?btw very informative video 👍

Still getting an unable to download system error???

Why is it my vent will not screw off. I feel the hex screw in there and it has tension but will not screw out.

Thank you so much !

This is not for DIY. I bought about 1000 dollars worth of crap just to make my boat look worse lol.

bla bla bla. dislike !

Do you still like the battery?

tried this method with 8lb leader. not as easy to do. the leader doesn't stick out like the heavy leader does.

So my biggest question is how do you like the unit after 3yrs and have there been any problems

I figured they probably had a place to enter your water draft and air draft if they were going to know the proper route to take you. Lol I use Rand McNally gps in my semi, and it has spots to enter weight and height. So it won't take me on routes with bridges under 13' 6" or roads with weight or axle limits. Rookie truckers usually make the mistake of using google maps. 😆

That's how I was taught to tie this knot thank you.

Will these work with Evinrude G2 twin 300’s?

A big thanks from Wales UK. Was just about to give up on this knot until I followed your way. Took about 3 or 4 attempts but when you get it you get it 😊. Nice one 👍

Was the 2000 grit sanding done dry or did you wet the hull?

Have you ever tied a red Phillips knot

Good Stuff.

Best explanation of how to throw a triple load yet. Great video

This is the EXACT same battery as Epoch for twice the money as Epoch. I mean the battery is EXACTLY the same.

How high up the sides is foamed? Would love to it.

Are you still running this battery? And still recommend it?

Great video on the actual application. Speaking of application, I’m looking to add a trolling motor to my TW 232 LXF CC with a 36v Li battery. Was wondering if 1 of the 100ah size would be enough to keep the boat on spot lock for several hours per day? Didn’t know if I’d need 2 batteries for that big of a boat with the hardtop that will act like a sail…

BRILLIANT CATEGORICALLY BRILLIANT

Thank you so much for this video brother, this will make it way easier to clean my boat.

If you change the orifice in your foam cannon to a smaller orifice, it will foam a lot more.... almost every foam cannon is designed to work on the higher 3000+ pressure, gas pressure washers, so with the lower pressure units the "Mix Ratio" in the foam cannon is not optimal, by reducing the orifice to 1.1 size, it reduces the amount of water in the mixture and gives a much better "Blanket" of foam that isn't as thin and "runny" which allows it to cling better and really work on that dirt. The orifice is located behind the quick disconnect abs just unscrews with a flathead screwdriver.