Thankyou for showing the full process. Really helps out man.
@colgandj3558 күн бұрын
Great info and good job on the video! God Bless
@geoffl20 күн бұрын
awesome, thanks
@CheeLee-c4r25 күн бұрын
Hey Man, You are talking too much waste a lot times to watching the video
@nicopolis737726 күн бұрын
No underlayment under the shingles ??? This roof is going to leak . Your roofers never put underlayment on your roof and you did not notice that ??? The reason your roof leaked is that a shingle roofing nail rusted and caused your roof leak . Best thing to do is apply water proof coating by roller . Cheaper than a new roof . Many commercial products : Henry , Somay , etc .
@pkfan5112Ай бұрын
Very poor repair, why don’t put black paper first
@jmb11643Ай бұрын
How long did that JB weld last for the hinges??
@johnschiffermuller4930Ай бұрын
Good video. A couple of minor suggestions. I found it easier to open the liftgate, THEN remove the lower end of the gas struts, then remove the c-clips. That way the glass was supported on the open lift gate. Then I carefully lowered the liftgate, slid the glass over and off the hinge. Putting it back on I partially opened the lift gate to support the glass, but still give me access, then lifted the gate the rest of the way and hooked everything back up.
@pcatfulАй бұрын
Put in new underlayment below the shingles. Of course this will probably do for a year or two.
@johli2 ай бұрын
Thanks for the info dude!
@jamesdean42822 ай бұрын
Only video that actually showed the detailed process of changing out the pump. Not just the pump assembly
@-mejor-que-nostradamus-61522 ай бұрын
There Is A Secret That I Invented My Self To Donot Screw It 😊 And It Will Be Double Longer Life And WaterProof Leak And 10 Times Stronger For Hurricanes. Amén.
@johncane41273 ай бұрын
The best video out there. I did this years ago and it’s still holding
@keith455-733 ай бұрын
👍
@frankjones52833 ай бұрын
There is a better tool for reaching under a shingle and removing or installing a nail.
@rustyhurd36463 ай бұрын
Thanks. Step by step just like you showed
@oldmansilas5593 ай бұрын
Terrible lighting. 🤦🏾
@firstpitstop4 ай бұрын
Did the repaire hinge still working after all these years or how long it lasted? I'm about to do mines it broke after replacing the shocks with new ones.
@ShadowHunter3324 ай бұрын
What about the underlayment?
@kinglui94844 ай бұрын
Where’s the dam paper @ dude
@Cata26905 ай бұрын
Was there a reason you didn’t use paper under the shingles?
@raczyk5 ай бұрын
Hi, thanks for the video. If you put cement fork shingles, is that permanent? Im truing yo fix a shimgle leak. Akso how to remove mould ftom undrt the plywood, from the leak?
@Autoshyne796 ай бұрын
Thick coat wax protects the paint from the sun
@robertramos85857 ай бұрын
Just came across this video. Mine did the same so it’s a little awkward but close.
@gasfeesofficial35577 ай бұрын
Great work brother! Loved the simplicity of your video.
@Sam9wilson97 ай бұрын
❤
@paul-rc7mh7 ай бұрын
Not bad for do it yourself but as a professional i would so some things different but expensive compared to yours Lol
@paul-rc7mh7 ай бұрын
They some stuff i used in between valley and pan that expans after use works very well
@paul-rc7mh7 ай бұрын
If you measure from where you end to where you start top and bottom same you will never saw tooth bottom
@paul-rc7mh7 ай бұрын
They still a vent you can use for metal
@paul-rc7mh7 ай бұрын
Venting in Florida is so important
@paul-rc7mh7 ай бұрын
2 inches off bottom prity tight with no room for error
@paul-rc7mh7 ай бұрын
In flats know because some contractors over tight the screws and the metal split
@paul-rc7mh7 ай бұрын
As a roofing contractor I've heard that before lol metal here is about 4 dollars a foot for instance a pan 5 ft 20 bucks
@iDionSingh7 ай бұрын
Super thank you bro
@shannonvaughan92618 ай бұрын
Run a plastic putty knife down the side to pop and pry the moulding off. Wash away whatever debri you can wish dish soap and water and then use decal remover wheel on a drill to get the adhesive off. Had both sides done in no time.
@ThomasBonnett-qx1ot8 ай бұрын
Where is the fuse on a Yamaha quad four
@ellecrowe32468 ай бұрын
Thank you so much for this! Did you remove the fuel pump fuse and relay first? I’ve got over a half a tank of fuel, should I wait until it’s near empty?
@carlosrebolledo13208 ай бұрын
Hello where can I buy those hinges for my 2005 yukon 5.3 motor I thank you in advance.
@sarah_farm8 ай бұрын
I never missed one video of yours,the food you made for your family looks very delicious and healthy,you are blessed to have an extraordinary talent,thanks for sharing your life with us
@Arandomwoman10 ай бұрын
The purpose t I build anything is to use the best options for the best outcome. I hate the use of cheap materials that go into the construction of houses. It makes sense to use materials that won't need replacement for decades, giving homeowners more time enjoying their homes rather fixing damages that were avoidable or hiring someone that may rob them. Thank you the video.
@NathanSummers-sh3ru11 ай бұрын
Hey man. I appreciate the video. This with help me with my upcoming roof repair. Thanks again.
@Poordirtfarmer11 ай бұрын
👀👍🏼
@martinsmythe341411 ай бұрын
Watched and used your video great. On question when you got to the top and slid the last repair shingle up under the existing shingle how were you able to nail it? thanks
@dentron9885 Жыл бұрын
Thanks for the vid, if you just have a little block you dont even have to jack the car. Get a hose with a jet nozzle and point it up there in the general vicinity next to the cat and blast while sweeping it a bit. Itll usually break up the clog and takes all of 20 seconds.
@whatscomingnext3605 Жыл бұрын
Thats what i thought watching this....
@JimmyHardy-cx5et Жыл бұрын
When did you do the roof job? How is it holding up?
@annabushka2686 Жыл бұрын
This is absolute genius!
@oldmansilas559 Жыл бұрын
That’s a bad design by GM.
@davelafaille2518 Жыл бұрын
Tapping metal to metal, no bueno! Put at least rag or shop towel inbeteen…playing with gas fumes bud…