Great video. Code of the ngk sparkplug? Thanxs

Hey, I got a leak in my power steering return line and it’s a metal line that loops to act as the cooler. Was wondering if it would be possible to cut the metal line at the leak and attach a cooler like this to it ?

Makes me just wanna buy a whole new car instead of replacing the dash 😂

Can you remove the bearing behind the clutch too ? Mine is noisy

Man your the only mechanic who tells you everything and don't skip steps like these other KZbin mechanics. Good stuff miss keep up the good work and show these mechanics how is really done.

Torque spec for the spark plugs? And for the bolts (10mm socket) holding on the ignition coils?

Thanks so much! Excellent!

Very good video, and instructions, great job. ❤

This method does not work on a V50 D2 from 2011. Or, basically it does work, however, the way to remove the clutch is different. The holes are not 5mm bolt holes, but just holes. There are 3 holes, and there's a tool which fits these holes to be able to hold the clutch to remove the nut. So you need a different tool and a different method.

I have a 2005 Volvo S60 do you think this fix will work on my AC compressor? I'm having the same issues currently

Will that hood fit on my 07 Yukon Denali????

Hi :) What about check engine after ??

U a bad chick !

Where did you purchase the dash from?

Help help. So what can my problem be on my 04 maxima if I replaced both oxygen sensors bank 1 and 2, the mass air flow sensor and cleaned the throttle body, what can be the reason it still stalls out?

If only the Bank 1 O2 sensor was that easy on the '07 3.5L Altima. The clown who designed that engine and the connector for that sensor should look for another line of work. The space behind the intake manifold can barely fit a fist. So disconnecting with removing the intake manifold is pretty much impossible. It's a totally different type of connector.

What is the torque spec for the subframe/ crossmember and torque spec for all the stuff?

Good Clear video. Thank You.

Why isn’t the warning of pulling the axle shaft out and possibly getting a vibration in the factory instructions? All that happened to me on my 2020 rav4 XLE AWD

Did that cause knocking noise or any misfire in a cylinder ?

So you used that sealer and nothing else? No gasket? No gasket maker? Just the sealer?

Where dit you put your spare tire with same size you put on your car?? It will fit on tire compartment??

Is this the same as a 7th gen install?

Can you put a remote switch on the BD to trigger the parallel for all batteries to be available?

*PromoSM*

Very helpful! Thanks!

Man's installing headers yet is still rocking the OG airbox with paper filter. At least pop in a K&N cotton filter to let the engine breathe a little better. As I comment on a 3 year old video lol

The one thing he didn’t even touch was how to get the bridge off wtf

Not gunna show us how it sounds?

Just installed mine!! Any tips to get these flanges to seal? every flange leaks, so I need to loosen and redo, but they look straight!

What a F.ken mess!!😅 I really don’t want to do it..🥴🥴🥴

Good job bro

nothing was covered

it helps to show the cover auctlly coming off and how or what you did to break the seal

I've got an idea what to do when my tires need to be changed

Nice, the PT's engine bay is so crowded I'm researching this for our 05 GT. What gauge wire did you use for the relocation and brand/type of terminals and fuse/breaker on both ends. I also saw you used a spray in the trunk area, and by the end of the video it was all black, was that something spraid only or laid on top? Curious on types, brands, etc for everything! Because ebay kills old links unfortunately. Thanks for sharing!

Hi! I wanna install the same kit in my Rav4, any issue so far with the lifting?? Greetings from Chile, South America.

Amazon, 40.00 for the tool kit

Did this on a 2010 maxima, b1s1 02 sensor unfortunately was frozen, so had to remove the intake manifold, and spray wd40, then torch. After i was able to free it, the threads were damaged so i had to rethread it, for it to work. Its a job that can either be easy if your able to free it or extremely difficult.

Is the exhaust stock besides the resonator delete and catless downpipe?

P r o m o S M

I have a green wire red wire black and blue wire on my summit box

Me thinking it would be difficult putting headers on because of the amount of work needed, it looks like an easy 5 hour job times my experience making it an 8 to 10 hour work 😭😭😭😭

Thank you for this tutorial. It helped me a lot today when I completed my bank 1 sensor 1 change. I thought it through for about a month during other Maintainance to the same area. The brainstorming time lead to doing the repair from the top and moving the mass air flow manifold to access the 02 sensor with and extended socket, torch wrench and swizzle connection. Bought a new jack from auto zone just to familiarize myself with the best wire route to take to execute the change without cutting the wire or keeping the car jacked up without jack stands. 🫡 @OnlyTheArts_

Thanks for the video! I just did this job this afternoon on my S40. I didn't replace the oil cooler hoses, so I didn't have to drain the coolant and just left the cooler hanging. No problems.

Is that the turbo or non turbo? I saw some motor mounts just like that on ebay.

How long did this take you to install?

I absolutely positively hate the hard CHEAP plastic dash in my 2012 sierra Denali. If I were to replace the dash when it cracked, I would look at covering it with faux leather and French stitching.

Exhaust leak in rear