What colour was the wire to splice into on the traction control button?
@mike_hayes16 күн бұрын
Have you got a part number for the sensor?
@RJW_Customs16 күн бұрын
Yes it is 1J0 907 543 A
@mike_hayes16 күн бұрын
@@RJW_Customs awesome thank you
@AZpatriot69.20 күн бұрын
What the set up on the engine and trans?
@RJW_Customs20 күн бұрын
Hi, so 700r4 with a shift kit but other than that standard. Engine wise it's a 350 small block, 4 bolt mains, stock bottom end as far as I'm aware, comp cams xe268h camshaft, with matching valve springs. Stock heads but some one at some point has had a go at porting them. Edelbrock dual plane I take, 750 cfm holley vacuum secondary carb, electronic ignition, hedman shorty headers. I think that's about it
@ryanwestwood925422 күн бұрын
So glad You found some power down low!
@RJW_Customs22 күн бұрын
It's where we all want it!
@trashpandaautomotive22 күн бұрын
Solid 💪 💪 💪
@RJW_Customs22 күн бұрын
Thank you 🙏
@britdragster22 күн бұрын
Nice. I was thinking peak power would be around the 290 mark so that's probably around 350-360 at the crank, which is a really nice street engine. Well done on dialing it in within 10% too. Did you change the timing at all to see if it pushed the numbers a little higher?
@RJW_Customs22 күн бұрын
Cheers roger! Yeah I wqs happy with how I got it, yeah we played with the timing a bit, initially we advanced it a touch and gained a little bit up top, then we retarded it a bit oast were I had it and thays where it gained the most up top but also all the extra it gained down low and across the board
@danleflem965124 күн бұрын
Hi mate, I’ve done the same in my T5 09 plate and the airbag light is always on, changed the loom for a new one and still the same. Any ideas ? Thanks
@RJW_Customs24 күн бұрын
Hi, if you did it with it live and it saw the airbag not connected at any point, the stored code will put the airbag light on until it is cleared using diagnostic software
@jknightssyiem9971Ай бұрын
This page deserve a follow.
@RJW_CustomsАй бұрын
🙏
@jknightssyiem9971Ай бұрын
Pin me bro before this goes viral 😍👌🏼💯
@jknightssyiem9971Ай бұрын
You deserve a follow.. I've followed this account From all the members at home . Took their fones and I subscribed your channel ☺️😅 I wanna see more coming 👀
@RJW_CustomsАй бұрын
Thank you
@RJW_CustomsАй бұрын
Let's hope so
@DDG-DownfallАй бұрын
BRUTAL
@RJW_CustomsАй бұрын
Absoloute savage isn't it!
@ryanwestwood9254Ай бұрын
Nice work, you made that look fairly pain free!
@RJW_CustomsАй бұрын
Genuinely don't know what people moan about when doing it!
@Skibidipotato123Ай бұрын
I was at goodwood today and it broke down when doing donuts
@RJW_CustomsАй бұрын
Oh really? Rotary reliability shining through?
@Skibidipotato123Ай бұрын
@@RJW_Customs Lol can I have a shout out in next vid please
@LeonRiviaАй бұрын
@@RJW_Customs nah it turned off for like 10 sec, and then went back to drifting
@RJW_CustomsАй бұрын
That's good then! I imagine it's pretty highly stressed
@rioalfiansyah6919Ай бұрын
Absolute beauty of a beast🔥perfectly the walk of an art by mad mike🤩
@RJW_CustomsАй бұрын
Combination of crazy parts all in one!
@henrylynch9437Ай бұрын
Oh my fuck that thing is insane!!
@RJW_CustomsАй бұрын
It is crazy isn't it!
@jknightssyiem9971Ай бұрын
@@RJW_Customsabsolutely A beast
@SmokeStack-yk3kzАй бұрын
This car is absolutely BONKERS 💯👌🔥🔥🔥🔥🔥
@RJW_CustomsАй бұрын
The video doesn't do it justice on how crazy it sounds!
@charlpieterse3529Ай бұрын
How did you get the deal board off?
@RJW_CustomsАй бұрын
I'm sorry I'm not sure what you mean by deal board?
@lknightsdotcomАй бұрын
Nice van. How many miles were on the clock when you bought it? Also, where did you find it? Autotrader, eBay?
@RJW_CustomsАй бұрын
Thank you! It was on about 140000 miles when I got it and I've had it about 7 years. I found it on Facebook marketplace
@SpiderjollyАй бұрын
what's the Kenwood model you bought? Cheers.
@RJW_CustomsАй бұрын
I'm struggling to find the model number without pulling it back out
@user-wq4ro6le2zАй бұрын
Someone trained her right! I wish she was my girl !!!
@MrGierosikАй бұрын
You could have moved it lower once you made the new pipes and fittings. Most of the intercooler is now covered. Additionally, the flow is worse when it is pressed against the bumper.
@RJW_CustomsАй бұрын
Yes I agree I could have moved it lower down but this was the simplest and cleanest option, yes it's maybe not in the most optimum position but it will still be getting plenty of air flow. Otherwise 90% of cars on the road there radiators would only be working at 50% as they are behind bumpers
@looneyrickstarАй бұрын
Hi RJW , if i already have cruise control on my multi function steering wheel and I upgrade the steering wheel with the ACC button can that be coded in or is it more involved? Many Thanks.
@RJW_CustomsАй бұрын
Hi Rick, Does your van have the distance sensor on the front of it to be able to use the ACC function?
@realMaverickBuckleyАй бұрын
Whut?? A Chevelle.. in England????? 😮😮😮😮😮😮😮😮😮❤❤❤❤
@RJW_CustomsАй бұрын
Yes indeed!
@Lucifer2.0287Ай бұрын
She can’t handle that thang
@RJW_CustomsАй бұрын
Damn right!
@ryanwestwood9254Ай бұрын
What an epic machine
@RJW_CustomsАй бұрын
Cheers man!
@user-yc9uj9on9uАй бұрын
Thank you very much for the detailed explanation! Could you please write down the code of the sensor that appears in the video?
@RJW_CustomsАй бұрын
No problems your welcome, I will have a check back through and see if I still have the part number for it
@joshkjohnson2 ай бұрын
Kudos for you trying to tackle this! I paid a shop to regear my axle as I felt this was out of my skill set.
@RJW_Customs2 ай бұрын
Thank you, patience was definately the key thing needed. I reckon once you've done it a few times you will start to get the hang of it and have more of an idea what way to go with setups to get it right!
@tonymoore49472 ай бұрын
Could you offer diesel leaking into the oil. Just had major work done. Same problem returned
@RJW_Customs2 ай бұрын
Yes you could get diesel leaking into the oil via the little oil seal in the diesel pump aide which I didn't change in this video
@ianwilcoxson15792 ай бұрын
Very useful video, did you put silicone on the block side of the pump as well ?
@RJW_Customs2 ай бұрын
Hi yes I did
@ianwilcoxson1579Ай бұрын
Thanks for the reply, just done mine same as you (so didn’t touch the fuel pump) can I ask how stiff should it be to turn the shaft, I need a pair of pliers to turn it, I was worried so I took it apart again but it’s all fine, however as soon as I tighten up the four bolts on the vacuum section it gets quite stiff?
@uksilverstackers4212 ай бұрын
Exhaust sounds awesome, gonna check out FabCo 👍 Which model mufflers have you fitted?
@uksilverstackers4212 ай бұрын
Just caught up with this.... Awesome day. At 7:44, quality burn out!! Cant beat the sound, smell and sheer power. Was there earlier that year for the FIA Main Event. Yeah Pro Mod is great, but a Top Fuel Dragster / Funny Car is an earth shaking experience, especially in the Grandstand 😊😊😊
@RJW_Customs2 ай бұрын
Thank you. Unfortunately I couldn't make any if the big events last year. I agree top fuel is amazing a sight snd everybody should experience them! But I just think you can't beat promods for how powerful and generally reliable they perform
@conordunbar99542 ай бұрын
Lovely jobs sir. Looking to do similar myself. Have you got the link for the lights as I’ve seen the link for the switch 👍
@RJW_Customs2 ай бұрын
Thank you very much, these are the lights that I used www.ebay.co.uk/itm/285317372188?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=4CUj8beeTkO&sssrc=4429486&ssuid=v2xawCMLTMy&var=&widget_ver=artemis&media=COPY
@ChrisandPolly2 ай бұрын
Hi there, How would you diagnose the difference between a tandem pump failure and injector seal failure? Before I dive into the injectors I was hoping to rule out less invasive potential causes to my hard starting in the morning in the mornings. No diesel in oil. Cheers, Chris
@RJW_Customs2 ай бұрын
Unfortunately lately there's no easy way to tell which is giving you poor start, does it smoke on startup? That would indicate fuel leaking past the seals into the bores. If there is no obvious sign, I would start with the tandem pump as its the easier and cheaper of the 2 repairs, if that doesn't fix it then it's going to be the injector seals
@ChrisandPolly2 ай бұрын
@@RJW_Customs There’s no smoke on normal start up, but on first start of day there’s a tiny bit of black smoke from what I assume is unburnt diesel. Clears in seconds then no smoke at all. I’ve changed fuel filter so assume that and the low pressure side is ok. Lifter pump in tank makes a gurgle sound when it primes.
@RJW_Customs2 ай бұрын
Generally all pds have a little black puff of smoke on startup. This could be a sign of worn seals as it's got excessive diesel sat in the bores from leaking past the seals. But I would still start with tandem pump without solid proof on the injector seals. The lift pump is it just a little noise or a gargle like it's filling a cavity that's got air in it?
@ChrisandPolly2 ай бұрын
Yes. It sounds like a squirty gurgle. Like when a water pump first primes. Different sounding to other lifter pumps on other vehicles we’ve had.
@ryanwestwood92542 ай бұрын
Did you get to the bottom of the mystory snall ball? Great work as aways cant waite to here it run!
@RJW_Customs2 ай бұрын
It seems to all work OK and I've since found quite a few of the small balls on the floor so I must have had a bearing come apart at some point in the garage and never swept them all up! Properly put a spanner in the works for a bit though!
@The_K_Man3 ай бұрын
What material did you use for the ceiling panels? I got some fake alcantara in dark grey and the glue came through the material and looked awful.
@RJW_Customs3 ай бұрын
I used a faux suede 4 way stretch with a foam backing. vandalised.co.uk/shop/campervan-lining-black/
@mrclarkey3 ай бұрын
Any links to the switch used?
@RJW_Customs3 ай бұрын
This was the switch's I used www.ebay.co.uk/itm/282126825471?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=YRTmJau9QrW&sssrc=4429486&ssuid=v2xawCMLTMy&var=&widget_ver=artemis&media=COPY
@mrclarkey3 ай бұрын
@@RJW_Customs appreciate the reply , will be doing mine soon so appreciate the extra detail you did on wiring 👍
@RJW_Customs3 ай бұрын
Your welcome, yeah I don't think there's many videos that cover the actually wiring side of it
@ryanwestwood92543 ай бұрын
The carvis looking great, good luck for the drag event, looks like a great event
@RJW_Customs3 ай бұрын
🤞 it goes well on the dyno this week in preparation
@Benjamin_Moore3 ай бұрын
It's so clean underneath! Defiently need to prep and paint mine when the weather gets better!
@RJW_Customs3 ай бұрын
It makes all the difference especially when working on it!
@70sport373 ай бұрын
Look at me look at me look at me !
@corbetcochran57003 ай бұрын
Perfect timing. I bet $10 to a donut that this b!ttch has zero lag off the line.
@davidconnelly46663 ай бұрын
That’s some sweet chop. Beautiful car. American Horsepower will always be the Sounds Of Our People.
@RJW_Customs3 ай бұрын
Thabk you 🙏, you can't beat the noise of an American v8!
@user-fe9nh4yp3b3 ай бұрын
Who's in the trunk
@RJW_Customs3 ай бұрын
🤣
@jasonsanders-fox51313 ай бұрын
Even the cameraman started to nod off 😂😂😂
@jasonsanders-fox51313 ай бұрын
Could have quite easily been 'the most regretted' practical joke in history 😂😂😂
@tylerhmmng3 ай бұрын
Anyone else catch the lifter tick?
@RJW_Customs3 ай бұрын
It's had a flush and all change now and all good again
@SmokyMountainPrepper3 ай бұрын
But lets ban wood burning stoves because of wood smoke!!!
@RJW_Customs3 ай бұрын
🤣🤣🤣
@randygerhart50763 ай бұрын
My 72 Duster 340 ci was built to the max and it did that every time I wanted, but it only got 5 mpg. 😊 That’s driving it easy too! ❤
@RJW_Customs3 ай бұрын
Trouble is you can't have a muscle car and not have fun while driving it!
@Benjamin_Moore3 ай бұрын
Thats so cool!
@ThisisUSA20243 ай бұрын
❤❤❤❤
@Coops4423 ай бұрын
Beauty 😍, tune choice too 👌🏻
@RJW_Customs3 ай бұрын
Thank you 🙏
@Jsweeken4 ай бұрын
Is it supposed to be diesel behind the first cover? Or do i have a bigger problem than bad gasket
@RJW_Customs4 ай бұрын
It's made up of 2 separate pumps essentially so yeah first one is a diesel pump, the second one (closest to the engine) is a vacuum pump
@Jsweeken4 ай бұрын
@@RJW_Customs yes thanks, I mean if there is diesel flowing behind the first plate or if it should only be inside the part with the springs? ( that you didn’t open in the video) I assume the axle seals that is included in the kit is also changed by open this “inner pump”
@RJW_Customs4 ай бұрын
That whole part will be full of diesel
@Jsweeken4 ай бұрын
Thanks I will take a look when I take it apart, can’t find any photos online in that area