8 ай бұрын
9 жыл бұрын
Пікірлер
@dennish9585 24 күн бұрын
I already change it and still doing same problem
@PaulsRandomness 24 күн бұрын
Few possibilities You got a bad sensor. It’s not plugged in tightly enough A wiring issue, a short etc.
@MrChuckyducky1 29 күн бұрын
What kind of drill did you use? Can I use a regular cordless drill? That's all I have.
@69-MinuteFix 29 күн бұрын
Any cordless drill should be fine. The difference is the drill bit. You need a masonry drill bit. Home Depot will sell come concrete screws and the matching drill bit with it.
@randyriggs5463 Ай бұрын
All that you really needed was a spanner flange to repair it. Other than that,nice job.
@dividav1224 Ай бұрын
Who else is here cause they bought the wrong toilet size? Fuck my life
@69-MinuteFix Ай бұрын
You mean the space from the wall to the flange? Most common is 12” I believe. Less common is 10”. Might be worth returning the toilet and get the same one vs trying to move the flange. I know Home Depot carries both.
@jenlo9126 Ай бұрын
I watched your video today. I also watched about half dozen other ones that told you the only way you could do it is by taking the handle off. That is false. Your method worked like a charm with just a basic flat screwdriver. It took me all maybe 2 minutes. Thanks for the instruction!
@69-MinuteFix Ай бұрын
Thanks for the feedback! That’s why I make videos!!
@christopherrycecr Ай бұрын
That is crazy just defrost the refrigerator
@69-MinuteFix Ай бұрын
That would have taken days. And I would have lost all food. This way I saved some of it.
@edwardbianchi1073 2 ай бұрын
Did not see him apply primer
@69-MinuteFix Ай бұрын
Keen eye. It is recommended. I didn’t have any. I’ve since looked up strength tests for primed and unprimed joints and there was no big difference found. Still I would use it if I had it.
@mikehlee69 2 ай бұрын
Why are flanges glued vs threaded?
@69-MinuteFix Ай бұрын
Good question. I never really thought about it. If it were threaded, it may be difficult to remove still as in most cases you can’t get a hold on what’s below the floor. Could be finished basement or crawl space.
@theantichrist4267 2 ай бұрын
You should have used a heat gun , after making your first cut !!! The pipe glue will soften after you heat the flange and you can peel the old flange out .
@69-MinuteFix Ай бұрын
Good tip! Could potentially help someone who’s watching.
@baddad5781 2 ай бұрын
Since this video is 3 yrs old, I'm curious to know how this flange replacement has held up since you sat the flange on top of that grout. I thought the flange might leak sitting on the grout like that. I appreciate you taking time to make the video.
@69-MinuteFix 2 ай бұрын
Rock solid. Cement floor so there’s no flex and no cracking grout. The flange sits on the spacer which is in the sanded grout.
@Mr.clintontoney 3 ай бұрын
Did this fix everything?
@69-MinuteFix 3 ай бұрын
Yes. This one sensor fixed it. No more warning light in dash, ac works and fan does t stay on after shutting off the car.
@Mr.clintontoney 3 ай бұрын
@@69-MinuteFix thank you so much for this !!! I have the same car same problem and yes ! It did work!!! Thank you brother!!
@69-MinuteFix 3 ай бұрын
@@Mr.clintontoneyawesome!! That’s why I make videos! Love a good outcome.
@tomdickinson9416 3 ай бұрын
Thanks! why did you have to take the door off?
@69-MinuteFix 3 ай бұрын
It made access to the bottom of the freezer easier to get the chunks of ice stuck to the bottom out.
@csb65536 4 ай бұрын
This is sadly a common problem with Whirlpool “frost free” refrigerator/freezers. Sadly, until now, I was told by so called authorized Whirlpool techs that it just caused by moisture freezing in the drain line, and it would be a good idea to defrost my frost free freezer once or twice a year. So I have been doing that. However, I neglected to do it now for over a year, so the door is frozen shut. As soon as I get it open, my sure fire fix is to buy a non Whirlpool refrigerator/freezer. The video was great, it does explain the possible issues. P.S. I am a different CS…lol
@alec1113 4 ай бұрын
All purpose glue , not recommended . Thank you for vid 👍
@warb3631 5 ай бұрын
ty!
@hardwarehenrietta5099 5 ай бұрын
Thank You
@vajona3894 6 ай бұрын
why put the plastic spacer in there rather than just filling with the brown stuff?
@69-MinuteFix 6 ай бұрын
It’s a solid surface for the flange to sit on as I glued it in. If I only filled with the sanded grout I could have inadvertently pushed the real flange too deep
@jenh47 6 ай бұрын
After over 2 minutes in crap ads, I'll watch someone else. Staying on this channel WILL waste your time!
@69-MinuteFix 6 ай бұрын
That does suck. Unfortunately I have no control over the ads. I’m not monetized or making any money from them.
@jenh47 6 ай бұрын
@@69-MinuteFix I can understand that and can certainly tolerate a short ad, but I think you're losing viewers with two back-to-back unskippable ads (total time 4 min 16 sec.). Wish I had seen your tutorial.
@69-MinuteFix 6 ай бұрын
That is excessive!!!
@joegabriel6001 6 ай бұрын
My old flange is not level. Off by mm . Would this work if I used more cement on the one side that is lower to make the flange sit even and not tilted.
@69-MinuteFix 6 ай бұрын
I don’t think so. If the pipe in the floor is not level you won’t be able to glue on a flange without it not being level too. If it’s only off by a mm I’d use a neoprene ring instead of a wax ring.
@emeraldkind 6 ай бұрын
Rubber gloves.
@69-MinuteFix Ай бұрын
I wasn’t too concerned. It’s my toilet. And just wash your hands well when you’re done. But yes gloves certainly wouldn’t hurt.
@emeraldkind Ай бұрын
@@69-MinuteFix 🤔 I don’t even remember watching this video. Thanks for your reply. I evidently needed to rewatch it. My mother’s toilet has a broken flange.
@Wayneman48 7 ай бұрын
no primer?
@mattc343 7 ай бұрын
Thank you! I just had the same issue with the defrost pipe and had to unplug/defrost the freezer for 48 hours before my roommate was able to yank open the freezer drawer. While we were defrosting, we wedged open the freezer drawer as much as we could with little blocks to let room temperature air in and also opened the drink drawer above the freezer. Who knows how long it would've taken otherwise...
@69-MinuteFix 7 ай бұрын
Glad it helped!!!
@Krumholt 8 ай бұрын
why did you use primer before glue?
@cook6052 8 ай бұрын
Outstanding tutorial! Do it right the 1st time and never go back. My Dad's wise advice over 60 years ago. The homeowner before me simply put a wax ring down on a concrete/tile floor and then siliconed the toilet to the tile on a $600k house!!!! How frustrating on at least three levels!
@randyriggs5463 Ай бұрын
Your dad was right . Go the extra mile first,and you won't get any leaks or call backs!
@mauriciofuentes5851 9 ай бұрын
Gloves 🧤 sir
@billhill839 9 ай бұрын
Great job my man😀
@786otto 9 ай бұрын
Nice job
@michaelpatin1362 9 ай бұрын
Great video, what kind of light are you using? I can see it propped up on the side.
@69-MinuteFix 9 ай бұрын
It’s an led work light from harbor freight www.harborfreight.com/500-lumen-led-rechargeable-magnetic-handheld-foldable-slim-bar-work-light-59536.html
@savygarnr9526 9 ай бұрын
That's why you shouldn't use that cheap plastic vinyl in your bathroom floor
@69-MinuteFix 9 ай бұрын
This floor is actually ceramic tile. Looks like wood.
@Erickhardaway 10 ай бұрын
I would’ve used a multi tool
@westonweigand1228 10 ай бұрын
They make repair rings that go right on the broken flange,if you don't want to replace the the old one.
@mussim2919 11 ай бұрын
Which glue you used?
@69-MinuteFix 11 ай бұрын
Universal type good for PVC
@Patricia-sr1ch 11 ай бұрын
Thank you! Now to find someone to do this...
@69-MinuteFix 11 ай бұрын
You can unplug for a day or two and it should defrost enough to open.
@johnneal9658 11 ай бұрын
Let this guy get his own gloves he should know better he must not be a real plumber NASTY
@69-MinuteFix 11 ай бұрын
Correct. I am not a plumber. Not that it’s any different but it was my house/toilet. There’s nothing caustic… just washed my hands after.
@anoldocastro4792 Жыл бұрын
Very easy
@alicepooper8562 Жыл бұрын
people do the stupidest things
@ronnym1977 Жыл бұрын
Did you change that outdated gate valve angle stop and rubber supply line too?
@69-MinuteFix 6 ай бұрын
I did! Went with a 1/4 turn valve and a braided line.
@salelpuma1541 Жыл бұрын
Good job keep clean
@Josephhoward28 Жыл бұрын
Might finally have that project I gotta give in and buy the sawzall
@gfysyoutube Жыл бұрын
Nice work!
@user-johnvajcner Жыл бұрын
Thanks for the video. Working on this job now and needed a good idea.
@Khankaka-u9y Жыл бұрын
My plumber has set up ptrap here is it correct elbove would be better
@mikejohnson9118 Жыл бұрын
DO NOT used Tapcons. They rust and or break. Use stainless hardware!
@Casey_Chaos Жыл бұрын
I just used JB Weld. It worked like a charm.
@kennp9184 Жыл бұрын
All of you "Do It Yourself Video Guys" should wear gloves. Other than that, Nice Repair.
@vrea77 Жыл бұрын
Do you have to glue it in if it slides into the pipe
@69-MinuteFix 6 ай бұрын
Glue is a must. It’s a chemical bond between the pipes and seal.
@614blessed Жыл бұрын
Are we supposed to glue it in????
@i.d.withkhadija2012 Жыл бұрын
I did this for 4 hours and it worked! Thank you!!!!
@69-MinuteFix Жыл бұрын
Glad to hear that! Thank you for the feedback
@JoseGomez-cg4is Жыл бұрын
You wronwater will leak between ffleng
@69-MinuteFix 6 ай бұрын
Wrong about what? Once there’s a wax / neoprene ring how will it leak?
@olivertaylor8788 Жыл бұрын
Good job..