Hi There, when I changing scenes, the I/O routing stays the same. When I made in scene 1 a stereo channel for IP 7&8, and go to another scene where I wanted to have 2 mono channels for IP7 and IP8. The I/O does not change. What is the correct way to save that in a scene ?

🤝🏻

What kind of file does the showfile on the USB needs to be to work? Fat32?

To use this as a send rather than insert ?

Hi Andre. Is it possible with pc (no mac)? Is there a similar device with usb 3.0 or usb 3.1?

Hi Andre, thanks for this good video. I followed this set up to split channels for a separate monitor mix for a tour a few months ago. I have revisited the same show for the next tour and I am in a bit of a brain fog! The layer I have for the non split should not be assigned to L&R, but assigned to the monitor mix. I can do the LR assignment but how do you assigned to the monitor mix? Usually select say mix 1 and raise the faders to assign that channel to the mix. What I’m unsure of is the layer with the split channels when selected should not be assigned to L&R? Is that correct?

I'm so very much erfreut to hear your advice my Freund ✌🏼🤪

Hallo ANDRE, Welche festplatte nutzt du? Qu pulte waren da sehr anfällig. - ist das bei sq auch so?

HEllo and thank you for your good expérience. So basically it is not needed to have a soundgrid DSP server while have the adaptator to RJ45 / USB3 thunder ? right ? Also , can you then RECRD and do FOH in the same time without much latency. ? , At no point it is required a DANTE CARD or INTERFACE ? .... Final Question, tou also insert in live professor other effectcs on any channel (voice, drums, guitars. .. etc .. ???) Thank you again

Hallo André, herzlichen Danke für Deine ausführlichen Videos! Ich bin tatsächlich auf eine SQ5 umgestiegen und arbeite mich gerade ein. Gibt es eine Weg einen Bus in einen anderen Bus zu schicken?

My thanks too for the video. Been using the desk for a long time and normally configure on set up day. But I thought I”d try out the iPad push for a bigger show next week.

Andre, In the aux section of Allen n heath sq6 what would be the difference between a group bus and an aux bus ?

Not very dramatic. Only subtle colouration. I'd try and take post amp.

Hi Andre, learning lots here on your channel. I have 2 questions. In church If i do a usb multitrack recording via sq drive of the main sermon, will it effect the sermon going on live streaming via output channel. Question 2 Is it possible only to record 1 input channel and leave the other channels out of recording when recording ro a usb via sq drive. How to do it ?

Hello Andre, on an sq6 Allen n heath is it possible to send a DCA to an aux channel and how ?

-sever :) :) Lars :)

Thank you Andre for all the Time you are investing on us, trying to make the world sound better with Music. this video is super helpful. Could you make a Video on how to use Wave or Professor with SQ6 for live performance. From A-z please

HI. Unfortunately I don't have waves card on my sq7. Have you done any tests with Waves Rack via USB? I tried with some plug-ins only on master bus it seems to work better at 96000/128. using a good PC do you think I could add some plug ins on drum bus, bass and vocals

Can you do all the effects on avantis and a separate one that’s in d pack

Use a channel and turn it into an extra group bus

I didn’t like any of them, I love the Yamaha and Midas reverbs 😢

Thank you very much for this informative insight into practice❤

THX, perfect explain

hello and thanks for the video. can we use this option on the mixer even if the channels from the stage travel on s-link? I'm talking about solid effects for the voice like an insert pedal. will I have to choose an aux and a free input in local?

Bester Tontechniker ❤❤❤

very helpfull thanks

thats 😮

Chris adler

HI. I have to use a similar setup with 2 sq7s and a gx4816. I, who am at FOH, receive s-link signals but can I use my local ones for master out?. it is possible because I have a processor near the FOH connected to the sub and main which I reach via aes ebu of the FOH mixer

Do you feel any difference between Ar2412 and dx168?

Hi Andre, We've just installed the SQ5 in our mosque and I'm reaching out for your assistance. Could you guide us on replicating the FX from the video linked below? Additionally, I've noticed that only some channels are being recorded onto the USB, not all. Could you help me understand how to ensure all channels are recorded via the front desk USB? Video link: kzbin.info/www/bejne/mJC2oIebeqdsotksi=Di2cPB-FYwaaKCSr Thank you for your support.

how can i delete a patch? for example i have 1 to 8 drum inputs but later want to remove one of these inputs, and then shuffle all the others along to the left one space. Can i do this without deleting everything and starting again?

For doing it, have I to connect the stagevox? For example ar24/12? O can I use this trick without connection other thing?

The eq and compressor do not work after the insert , correct? In other words whatever comes after the insert gets cancelled?

Can you show that on avantis

Hi! I would like to know if on the sq5 I can use USB B - USB C cable instead of USB B - USB A to connect the mixer to a laptop for multitrack recording. Thanks!

thanks 😎

Thanks 🙏

Hey andre, i have one question. can u use live professor along with Multitrack recording via DAW? thank you

What is the equivalent effect to “Room Reverb”?

I wanna know what each thing does in the reverb

Would you be able to play more than 48 channels using two sq consoles? Like using the 48 from one and some form the other one?

SQ-Pac would be an instant yes.

Hi, i saw in your SQ5 BOARD can you explain how to assign all channels mute at a time for soft key No. 1

❤

Compré unos FX pero no me salen en la SQ7, ya registre los números DNA y

😂😂😂 👍👍👍

Funny tune!! 🤩🤩

Perfect - just perfect, simple, to the point and easy to understand, thank you.

How ‘bout patchbay?