Just got a brand new cat 2000 OEM controller and the flow sensor is not working it's telling me I need to drill into a port location but there is no Port location
@mcarmel124 күн бұрын
Why does my new Hayward TracVac’s hoses keep twisting & tangling? Pool not getting clean as the hoses are twisted up in just minutes. Terrible experience & probably will return if this can’t be resolved asap. 2:24
@HaywardPoolProducts23 күн бұрын
Hi there, you will want to disconnect all your hoses, and lay them flat on a good hard level surface in the sun, this should help take some of the kinking out of them. Then we would recommend when not in use to stack them individually instead of leaving them connected in a coil.
@mcarmel123 күн бұрын
@@HaywardPoolProducts these are brand new hoses that just came out of the box and are being used for the first time. They have not been misused. Is the machine itself broken? It works for a few minutes, but then starts turning in circles and causing the twists. I’m seriously about to return the whole thing. I will say that these hoses seem to be made of a thinner and less durable plastic than my prior Hayward hoses.
@HaywardPoolProducts20 күн бұрын
I understand. Please refer to this TracVac Trouble Shooting Guide and turn to page 20: hayward.com/media/akeneo_connector/asset_files/T/r/TracVac_Troubleshooting_Guide__TVAC_TSGa__0e88.pdf. If you find you still need assistance, please call your nearest Hayward-authorized repair center. You can find one here: hayward.com/locator.
@citizenbobx24 күн бұрын
I think I'm just going to rely on my timer to shut the thing off and stop messing with this interval crap! I think it slipped somehow, and now it's almost NEVER running, and my pool's going constantly going yellow to green. This video expalined the process only slIghtly better than the documentation, which is TERRIBLE!
@citizenbobx24 күн бұрын
It seems like this only runs when it feels like it. Maybe an hour a day? I have NO IDEA how to program this thing based on these instructions. This has to be the least intuitive design I've ever seen!
@BrianClark-yf7op28 күн бұрын
How the heck can I control the BLOWER on the Omnilogic app? Mine is 2HP and way too much I do not have a slider when i go to the blower. I can just turn it on via the app or not
@abbeypasАй бұрын
I currently have a mechanical time clock still in place. What happens to my programing when the clock shuts off. My objective here is to have the pump only on for 6 hrs at full speed. I hope you can help answer this as no support line for a hayward tech.
@LazarezsirovАй бұрын
So pretty
@angelaflow6981Ай бұрын
Thank you. That's exactly what I was looking for.🙏👍👏👏
@coziii.1829Ай бұрын
I just got mine it says Flo all time temp is 76 should be 85 Water level great Did two flushes
@vegas1854Ай бұрын
Any recommendations on how to quiet it down affter about 5 years of use?
@GianfrancoBaggio-g4cАй бұрын
Hola tengo un sisitema aquarite y le cambié la celda empieza trabando bien y después se dispara a cero
@DouglasVargas-c1wАй бұрын
Una T9 es para cuantos galones?
@IOSARBX2 ай бұрын
Hayward Pool Products, amazing video it was really good
@moth_la2 ай бұрын
These are horrible machines. Flips upside-down constantly does not clean.
@TommyJones492 ай бұрын
Have tristar SP3210X15 single speed 2 questions about Hayward Pool VS Pump, 1.85 HP (W3SP3202VSP), 1. Will this fit in place? No pvc alterations? 2. Is it same 3 wires, 2 yellows one green? Making connections simple.
@kayjay77802 ай бұрын
how do you know what speed to use? vs pump hp
@LaserNrg2 ай бұрын
Our spa lights do a slow color fade in the regular solid color mode even after pushing the reset button? How do I fix this ? Thx
@elimd.76092 ай бұрын
Hola tengo una de estas pero no la uso con sal es lo mismo con todos estos consejos? Ya que le pongo cloro al agua también y aun asi se pone verde en las paredes es muy duro todos los dias es lo mismo me puedes por favor ayudar que debo hacer gracias!!vivo en Texas en este momento estamos a 100f
@peteflynn39232 ай бұрын
As far as the “pretzel “ hose problem, my hoses have never been coiled because the navigator is always in the pool. I have experimented with the number of hose sections and with nine I get the least tangling, but never none. Im on my third navigator and have never been without the problem!
@peteflynn39232 ай бұрын
I have a pressure gauge, not a spring tool. What is the correct pressure gauge for correct operation?
@ahginga2 ай бұрын
I dont have a t-15 display at the end i can only hit 7x and it goes back to main… i do have an 88-2 setting what does that mean.. and if i go up to super chlorinate and back down goes to 88-3 then 4 then 5 back to 0 …. Are those my type of tcell??
@lebotube642 ай бұрын
Was most interested in the niche installation. Is there a video to show me step by step instal? Thx
@jeffbell73092 ай бұрын
Does it save money to wire at 2:20 versus 120?
@dennistran55682 ай бұрын
So I just bought myself a new pool cleaner. I’m trying to set it up and realize I have a suction port. I’m stuck on step 3 where it says attach the regulator valve. Do I attach it with the first connector hose off from the suction port? I’m a bit confused on that step.
@HaywardPoolProductsАй бұрын
Hi there! It depends on your suction port. It acts as a bridge between the port and the cleaner hose, but sometimes you may not need it. You can reference it here: hayward.com/media/akeneo_connector/asset_files/Q/R/QRGTV100_RevC_25cb.pdf
@jlnovak72072 ай бұрын
Does the cell cycle during use?
@katpac12 ай бұрын
Do you have a parts manual for the caddy? I'm missing the spacer for the wheel assembly.
@LOREMIG2 ай бұрын
This cleaner clim wall
@lla3012 ай бұрын
How do you change the button???
@daat943 ай бұрын
What happens if the xe pump immediately goes into this error mode when the power is applied? It’s wired to a two pole 15A breaker and routinely trips. But an electrician measured the live load carrying current and it was only 8.9 amps? Doesn’t track why it would trip or the xe pump being in this low dc internal voltage error state. Very frustrating
@briankellogg86033 ай бұрын
Great video for replacing seal kit. Really appreciate the time put into a step by step process. Thank you!
@AlexDot-rd9mo3 ай бұрын
Hi. I but new cell t 5 . All work just question. The led green generating all time on? I am cheking the pool water exit I see the hlorin making sometim the % 30 . But the led oll time on green?
@JasvantPatel-u2e3 ай бұрын
Pool control unit trip bracket For pool filter 1:18
@gabrielrivera19153 ай бұрын
These are garbage! Don’t waste your money ! On my 3rd light and it just went out. 3 lights in 9 years at $1k a pop
@monicagsmusic79233 ай бұрын
My screen it’s saying slo: and generating, power, check salt and inspect cell light are on. Could you tell me what to do? Because the salt it’s almost on 7. I had the strips and did read that. Thank you
@StorybookMom3 ай бұрын
Why I upgrade my system 4.8 to 5.0 and all the sudden my pump stop working
@HaywardPoolProductsАй бұрын
Hi there! wYou want to see if restoring from the back up, if you created one, corrects the issue. if not, please reach out to your Hayward-authorized repair center to confirm wiring and programming for pump.
@ritewaypoolsandspas91433 ай бұрын
How you set schedule time for high speed
@Dell48343 ай бұрын
BRO!!!!!!lol....those tiny machines lol...im a 2 shot processor 10 ton molds full rotation molds...it takes me 4 hours to change process and do try out before i do start up.....i do all purging and prep qork program new mold the i have to remove and set not only the mold the but webber unit behind our molds which makes it a full rotation mold...and those are easy compared to changing a mold along witht the center core and shaft ...and we have older machines so we get alot of mold protection alerts...but good vid nice to know our trade is growing
@vincefava79294 ай бұрын
Great video, thank you. I just changed the t-15 cell and it now reads 4000ppm average - how do I program the board to get the ppm down to within Cl range? Do I just change the % from pre-existing 55% to a lower %?
@HaywardPoolProducts26 күн бұрын
Hi there, do you have a S3 system or an AquaRite system?
@doncameron45104 ай бұрын
Hope your problem doesn’t hinge on corporate help because they’re trained in the school of Trump ( never take responsibility, they’ll throw anybody under the bus.)
@AlexDot-rd9mo4 ай бұрын
Hi. What I do if I don't have cell tipe menu . Just 7 screen. In 8 time it us coming back to main screen.
@Karen-we4kz3 ай бұрын
I have same question here... If ai press 8 times, is not screen for the cell type :/
@pollyjackson52124 ай бұрын
Cell doesn't even last a year
@Natedwebb4 ай бұрын
What gage wire do you need for the 230?
@kristinfoley73344 ай бұрын
When I push the +/- i can’t reset the number.
@HaywardPoolProducts26 күн бұрын
Hi there, what specific system do you have? What are you referring to that has the +/- on it?
@rhuggard20114 ай бұрын
Arizona water needs a 50/50 mix and 30 minute soak. Anything less leaves mountains of deposits.
@asafidan31274 ай бұрын
This pump is trash
@JohnFletcher-wb5sj4 ай бұрын
T cell number?
@JohnFletcher-wb5sj4 ай бұрын
How do I determine what Tcell number I should use?
@sterlingmortgagepropertymanage4 ай бұрын
If it’s installed on a timer and I don’t program out change anything.. am I correct it will self prime for a period and then just run on max until timer stops it?