I believe PGW is made by XYG

Thank you for your time to teach,where can I buy those tools??

Thanks Bro , I was able to do my window replacement successfully 🫡🤝

Both ..I use to work for Mygrant’s own and after market need to meet dot safety requirements

don"tlay your tools on the car.

slow down if you are trying to instruct a how to video.

The shade does not allow the camera to pickup the details of what you are doing and does not help the unexperienced.

What about 2016???

Hie my window is not going down

Thanks for the precious video.Can you indicate me please where is the Humidity sensor cable to replace in the new glass ?

Good shit bro,just did my window,side note,you dont have to take that side bar out all the way,just take the top screw out and push it to the side 👍🇺🇸🇧🇦🇺🇸🇧🇦👍

Thanks it helped

@5:38 That rubber piece, if you want to put a new one, how to find the right one for your car? Is it the same as weather stripping door seal? I have 2009 Nissan Sentra. Thank you for the informative film.

close the door for the automatic up to work

Why didn't you put the foam block back in?

Pop that glass lol

I’ve had 2 replaced in my jk in the last 2 years. Luckily I did not have to pay any deductible.

The tiny screwdriver is a PH00, not a T00. PH00 is much more readily available!

Nice work guys! Trying to replace my wife's jeep windshield and refuse to pay a 1k deductible. Very helpful.

Whats the cost to replace it?

You put the wipers back on incorrectly.

You know that there’s a speaker in that dash that you just poured water all over?

you freakin butchered it on removal... there are videos that show where all the screws are.

Thanks bro... That blow it with my mouth comment was wild 😅😅😅 good job on the vid

Ok

Where was the screw with the tape on it !???

Awesome

Good thanks

Thanks

I can do that in under 10 minutes with a thin piece of plexiglass

This would be a great video if only we can see what the tech is talking about out most of the video all you see is the background

are the front glasses the same for crew cabs and quad cabs just the front ones

Thanks for the video man, it WAS very helpful. Now I “Gotter Dunn. “ And now it’s time for a cold beer, I’ll drink one for you. 🍻

Thank you !! I make a mess today, trying the hard way , I appreciate it the video

Thanks! great video

4 Minutes job🤦‍♂️

WTF😂😂😂👎🏻

Why didnt you use a bat? Wouldve been faster than using a cold knife. Especially since the glass wasnt damaged on any of the sides. The line wouldve cut thru much faster.

this also works on a 2020 ram 2500. thank you for the video. helped a lot!

Thanks, I was able to refer back to the vid to clarify how you got that glass in, our Civic has external weather shields and I still managed to get the glass in without removal. Thanks for sharing, made the job much easier knowing any of the areas to watch for. A few very small differences on my 2020 ( a couple of extra trims, brackets and extra wiring loom to accommodate speakers) - and the 1 thing I tripped up on was I didn't confirm that I had the flex window guide untwisted. with the weather shield, I didn't see the top come out and twist. An extra 10 min, but the process was mostly done at night, in the driveway. Thanks for the help.

Appreciate it! I would have messed with that damn thing for a long time before taking the top track out! 28 years in the industry, but still learn something new every day!!

I turned on the car without it being connected and now the lock it acting up how do i reset it

Thanks it was really fun watching you do your first windshield😂

Follow along make it easier just the last step putting the door panel I bet you where already irritated haha

Went from being the easiest windshields to replace to now the most complex. Been sitting in this Subaru for 30 minutes trying to get the camera cover back on 😂😂😂

Mauvais travail mon amie

Thais helped me so much! Thanks man

Very good informative video. The only downside in this demonstration was the pack of protection applied to the inner sills of the vehicle. I mean that they could be marked or contaminated by your footwear whilst standing up on them during the cold cut and glue application. You did mention that you never put your feet in to the cars footwell, you can if you protect further.

Thanks much! Was able to replace mine from watching your video.

Where did you buy the glass?