Yall can't even fight yall bunch of young pupps😂😅😂😅
@andresdelacruz11028 күн бұрын
How do I know what’s the negative and positive?
@colin77617 күн бұрын
Hey bro, it only matters if you are installing LEDs
@colin77617 күн бұрын
If you are, then plug the circuit board into the car, turn the lights on, and touch the led pins to the board and remember the orientation. Good luck bro!! 💯💯🤝
@jocelynbey59448 күн бұрын
Thank you for the video.
@colin77618 күн бұрын
You’re very welcome! Thanks for your comment!! 💯💯🤝
@Nomadic3189 күн бұрын
Hey, I'm working on a similar build. Have you had many issues with ground clearance running the exhaust pipe that way? I'm a bit concerned about it but I haven't found a good way to avoid it with a front mounted turbo.
@colin77617 күн бұрын
Hello!! It’s definitely annoying being low there. My next go around I’m going to try and give it a little better clearance. There are ways around having to go under the subframe. More modifications are necessary though. 💯💯🤝 good luck with your build!!
@matthewprice7569 күн бұрын
Did you have to reset the car any how. I solder the cluster and it didn’t work.
@colin77619 күн бұрын
No, if it doesn’t start working right away it seems to have not been fixed. Sometimes this code can be caused by the fuel pump or a bad wire. If it is the cluster maybe the pin didn’t get heated up enough. Sorry to hear it didn’t work bro. Good luck with finding the cause 💯💯🤝
@mxjuxior24189 күн бұрын
Recommend drilling some big size holes under basket for quicker fill as well as upgrading your pump wire to 10 gauge as the higher power pump will heat original wires
@colin77619 күн бұрын
Thanks bro!! Appreciate the tips!! 💯🤝
@anthonycocozza24809 күн бұрын
Hold the camera straight
@colin77619 күн бұрын
Hahah sorry brotha 💯😂🤣🤝
@RizziLays9 күн бұрын
Respect you
@colin77619 күн бұрын
Thanks I appreciate your comment! 💯💯🤝
@thatonev8guy9 күн бұрын
Do they have to be 12v or would 3v work
@colin77619 күн бұрын
Usually have to be 12 volt. A 3v may break due to it receiving too much amperage.
@proobuio10 күн бұрын
Yoo you gotta tell me the set upnon that 5.7
@colin77619 күн бұрын
😂🤣💯💯💯💯🤝
@alilittle241210 күн бұрын
@colin7746 did you ever figure this out
@frankenfive1710 күн бұрын
How much she pushing?
@colin77619 күн бұрын
An estimated 500+ whp. Will get er on the dyno here soon!! 💯🤝
@frankenfive179 күн бұрын
@@colin7761not bad at all !
@DIEBYIT10 күн бұрын
You know he's got those things those whistling things that Go wuuuu tu tu tu tu
@colin77619 күн бұрын
Hahah you’re right 😂🤣💯🤝
@blue_ratchet12 күн бұрын
Is it swapped?
@jordansullivan369713 күн бұрын
Dude I can’t believe you’re in NS! I’d love to do this to something sometime lol but I need a better vehicle to do it to first lol
@colin776112 күн бұрын
Heey bro!! You must be Scotian too eh!? 😂 Glad to see people on here from my area. Haha i appreciate your comment! Take care bro!
@jordansullivan369712 күн бұрын
@@colin7761 I got a 5.7 in my ram I was thinking about boosting and lowering to make a burnout truck. Problem is it has a 65rfe and I don’t think it would handle the power well lol
@colin776111 күн бұрын
That’s awesome bro, I have a HEMI Ram as well with the 6speed. I’ve thought about boosting it and had the same thoughts as you. I may boost it one day and upgrade some weak parts of the trans, but i came up with the conclusion It’d be easier to boost an 8 speed Ram. One day bro! 😂 take care! 💯🤝
@kengriffith2413 күн бұрын
Hi great video on the jeep trans…1 question… where did you get the kit? Thanks
@colin776113 күн бұрын
Thanks! I appreciate your comment. I got this on Amazon bro!! Take care ! 💯🤝
@sissybaby938013 күн бұрын
Computer controlled cars are junk.
@barry.rupisan14 күн бұрын
Hey, thanks for the video. I was struggling today to remove the rear facing nut for the upper control arm on the passenger side today. I’m going to take that bar off tomorrow and try again.
@colin776113 күн бұрын
You’re very welcome bro!! It is a bit difficult to get to. Good luck with your repair!! 💯💯🤝
@AndrewLeak-q9o14 күн бұрын
What is the difference
@colin776114 күн бұрын
What is the difference of what? 🤔
@aaron7114 күн бұрын
I think I need to do this on my 05 Magnum... I have a squeaky spinny sound at low speed from under the console. How hard is it to get the whole driveshaft assembly out to do this job?
@colin776114 күн бұрын
It’s not too difficult if you have the tools and know how. It may be a bit harder if you live in rust prone areas! 💯💯🤝 good luck with that bro!!
@aaron7114 күн бұрын
@@colin7761 (shakes in Massachusetts rust) 😄
@colin776110 күн бұрын
Hahah I feel the pain bro. 😂🤣🤝🤝💯
@antcarter413315 күн бұрын
How much psi you running
@colin776115 күн бұрын
9-10 psi
@Deryan2valid15 күн бұрын
did you splice the high voltage wire?
@bflow155415 күн бұрын
i took my car by the dealership and they talking mad loot to fix p0660 code lol
@colin776115 күн бұрын
They always do these days bro!! 😂 good luck gettin er fixed! 💯🤝
@BobbyRoss.16 күн бұрын
Need to make sure you dont heat soak it bro
@colin776115 күн бұрын
Yeah you’re right bro! 💯🤝
@BurningDownUrHouse16 күн бұрын
did you replace the tensioner?
@colin776115 күн бұрын
Yes 👍 💯💯🤝
@lspaul1318 күн бұрын
How are they holding up ?
@colin776118 күн бұрын
So far so good! 💯🤝
@tomwa12218 күн бұрын
I’ve known you since 2018 😅 You might have forgotten me because we met on Fiverr
@JonathanCrappers20 күн бұрын
holy fuck i need this in mine. What kind of power are you making?
@colin776120 күн бұрын
Estimated 500whp 💯💯💯🤝
@Neal-lf7rk22 күн бұрын
Ouch 😢
@colin776122 күн бұрын
You’re right bro!
@matthewprice75622 күн бұрын
How do you mean to tape the needles. Like where they start. ? And also can I drive the car if I need to move it without the cluster
@colin776122 күн бұрын
Yeah, just use the tape to mark the position of where they go when you put it back together. 💯💯🤝 yes it can be driven with it out! 💯🤝 take care bro and good luck with the fix!
@matthewprice75622 күн бұрын
@@colin7761 thanks for the quick response!! Gg
@colin776122 күн бұрын
You’re welcome bro! 💯
@brandongaskin460622 күн бұрын
I have the same issue I think on my rt 06 charger, what type of wire should I get to solder to the original one? Thanks man
@colin776122 күн бұрын
Right on bro! Make sure you check the fuse first if you haven’t yet. A good replacement wire would be an 18-16 gauge. 💯🤝
@juansolares24222 күн бұрын
Hey friend, what brand and number do you recommend for my 2006 Dodge Charger R/T rear differential?
@colin776122 күн бұрын
Hey bro ! Do you need a whole replacement diff?
@juansolares24222 күн бұрын
No only change oil next wekend
@colin776122 күн бұрын
Ok bro! I’d go with a 75-140 viscosity. Brand shouldn’t matter too much as long it’s not the cheap cheap stuff 😂 anyway good luck bro hmu if you have any other questions. 💯🤝
@juansolares24222 күн бұрын
Thanks greetings from Salt Lake City Utah👋🏻It has 170,000 miles
@colin776121 күн бұрын
I appreciate you bro, have a good one! 💯🤝
@jarederisman527922 күн бұрын
Did you make it yourself?
@colin776122 күн бұрын
Yes bro! 💯💯🤝
@jarederisman527922 күн бұрын
@@colin7761 do you produce kits for others?
@briankissel766123 күн бұрын
It's Dutch. Dodge, Chrysler,Jeep, Ram.....sold the companies to Stlantis. @colin7761
@colin776123 күн бұрын
Thanks for the info bro!! 💯💯
@Shadowbanimakeanother24 күн бұрын
Finally a credible dodge build i can get behind. Nice set up. I used to have a nitrous 426 stroker back in 2010
@colin776124 күн бұрын
Thanks bro appreciate it!! 💯😂 that’s dope it must have been a ripper!!
@Shadowbanimakeanother24 күн бұрын
@@colin7761 it was okay dipped 10s with 24s and 4 subs. Lol
@briankissel766124 күн бұрын
Buy an American car next time, cops will give you way more slack if you do.
@colin776124 күн бұрын
What kind of car would you consider this?
@jorgedamian640324 күн бұрын
Can we get a couple of revs please and thank you
@colin776124 күн бұрын
For sure bro!!! Coming soon! 😂 💯🤝
@forcedtomakeanaccount762824 күн бұрын
Looked good for 3 frames😂 sounds nasty bro
@colin776124 күн бұрын
Hahaha will have to get a couple more frames next time 😂 💯💯🤝
@Dire_wolfe24 күн бұрын
You need at least 1 more person to help record
@colin776124 күн бұрын
You’re right bro!! 💯💯🤝
@MoparMafia5.724 күн бұрын
Got a bad harness. Have had 3 cars with same exact issue … there’s a bad wire that breaks closer to the plug .. u etheir can jump the wire like u did or put a new trans harness on which isn’t cheap .. hole harness
@colin776124 күн бұрын
Thanks for the comment bro! I figured it had to be a common issue, but there’s not much info I could find on it. Is the bad wire usually near the connector up top under the hood? Or one of the connectors inside the vehicle? I figured it had to be a bad wire or connection. Have a good one bro! 💯🤝
@EricGilliland-g1h24 күн бұрын
It’s not his sound lmao ya are slow
@colin776124 күн бұрын
Hahah unfortunately some people are 😂 🤣💯🤝
@kylechupick223224 күн бұрын
Where you from?
@colin776124 күн бұрын
Canada bro!! How about you?
@kylechupick223224 күн бұрын
@@colin7761 nj
@colin776124 күн бұрын
Nice bro!! 💯🤝
@Justnice2625 күн бұрын
So original bro!! Uh Derrr “”I don’t know why derrr”, “ it’s not even that loud “ proceeds to sound like a shitty Honda civic 😂😂
@colin776124 күн бұрын
Don’t hurt meh feelers
@Usmc511325 күн бұрын
They are giving you tickets because it sounds like shit 😂 sounds like a civic with the exhaust cut off completely blowing through a megaphone!
@colin776124 күн бұрын
Bruh don’t break my heart like that
@Usmc511324 күн бұрын
@@colin7761 😂 brush, I'm dead lol
@colin776124 күн бұрын
Hahah have a good one my guy! 💯🤝
@soufianDEMOS25 күн бұрын
I had my transmission totally rebuilt and since I had it installed no problem at all. Then 2 months later, I went WOT for short distance just to enjoy the sound of my CHARGER RT 07 with the new exhaust line. The engine went into safe mode and got the icone light up. But when I look at the code through the menu of the car, it says it is all good. And few minutes later, back on the road. Eventually the engine icone goes away. Yesterday, I plugged my HP Tuners and to figure out what is going on. I got two codes; P0730 along P0219 (Engine Overspped Condition). What do you suggest ? Thanks for that valuable video you shared here. Keep up the good work.
@colin776125 күн бұрын
P0730 Incorrect gear ratio. This code is set when it is detected that the transmission output is spinning at a different rate than what it would expect. So it could be either a sensor or transmission/ transmission fluid issue. I’d check for leaks first. Check the transmission fluid level to be sure it’s at the proper mark. (If you are able to) The p0219 means the engine went faster than it should have, possibly caused by a slipping transmission. If the fluid level is good, Clear the codes completely, then drive around and address any recurring codes. Lmk if you find anything!! 💯🤝 I appreciate your comment! I’ll be here if you have any other questions bro!!