Thank you for this! I am thinking of getting the MK2P-I relay. Do you think that would work to connect a 230vac 6.1A pump to a float switch? I need to set it up so that when the float is down, the pump will turn on and then turn off when the float is up. My main issue is that the pump requires 2 hot wires. I've been trying to find info on how to wire this. My brain keeps getting confused on whether I'd need to wire it to be normally open or normally closed. Any advice would be greatly appreciated.
@jaken13192 ай бұрын
So if I put pin 13 and 14 to a USA 110v plug can I plug it in forever ??????? 250V 5A
@jaken13192 ай бұрын
If I plug one into every outlet will the stupid meter electromagnetic field make it past the closest one?? 😂😂😂😂
@Kael0903 Жыл бұрын
Hi mind pm-ing me how much it will cost me to get this repaired?
@BMWRepairsSG9 ай бұрын
Where you located?
@sham1234567891 Жыл бұрын
Good video. Sound level too low.
@urbanirrigation Жыл бұрын
very clear english
@mosesmakanga6308 Жыл бұрын
Nice one
@AlmightyEye Жыл бұрын
Can't hear you!
@rayjohnson78862 жыл бұрын
Poor audio it's going in and out.
@stevewright12722 жыл бұрын
How I nuh show where to put the wire's
@nufailfuzoolla35802 жыл бұрын
Sir how to check if a relai is good or bad with multimeter
@RobinWhistles2 жыл бұрын
Pity you didn't wire the rest showing how it can be used.
@BMWRepairsSG2 жыл бұрын
It depends what you want to use the relay for, as the points are basically N/O, N/C. e.g. say you need a signal from a pump to activate a motorised valve; you wire the N/O points to the Pump and N/C to the valve or vice-versa.
@MrPunch052 жыл бұрын
Sound is very low...
@orenbell16452 жыл бұрын
Sometimes
@freytube12 жыл бұрын
nice, quick and clear thanks
@vongkea67682 жыл бұрын
good
@islamic313993 жыл бұрын
Great
@smittygoodman40713 жыл бұрын
Can't hear shit on this video.
@osmankjr71503 жыл бұрын
tysm u really helped
@sudeshputran693 жыл бұрын
Super
@md.rezowanmiah66563 жыл бұрын
sound quality is not good
@josetorree72373 жыл бұрын
Wire a ligth or a load
@user-hy6lz7ik3l3 жыл бұрын
👍
@lo-fistudio2073 жыл бұрын
Good brother
@vfgrfbgrb3 жыл бұрын
So when it is energized it closes
@lazycarper79253 жыл бұрын
please can you help a noob, can somebody tell me if i can wire a 3 pole relay as a single pole, i think thats what i want/need?, i needed a relay to turn on and off from - 24vac,on the coil side-, 240v 35a on the main load , and with out spending silly money i could only find a 3 pole one cheap, thats 35 amps , all i need it to do is when activated by the 24v ac , allow the current of my 240v ac to pass to make the circuit, and that can be just the live or the live and neutral, etc etc if it can be done?, would wiring it so my live splits and goes in to all 3 poles and then out all 3 poles(when activated), to give more current, as its for my mig welder ,(24v trigger), so more amps the better, thank you
@zacreynolds60453 жыл бұрын
I don’t think you’d need to wire the live into all three poles but yes it would work fine for your purpose.
@David-ty3yo3 жыл бұрын
Before doing the job get your microphone working properly
@PBS-nm1uu3 жыл бұрын
what is the name of the base??
@umargul56443 жыл бұрын
Well done
@AnilYadav-iv1zn3 жыл бұрын
me anil kumar yadav 9315663500 my 2 ret 55 par pcs my4 55
@mikepasko74933 жыл бұрын
Please learn how to talk English ......can not understand your language .....you have a very bad accent
@MrAndyloz3 жыл бұрын
is there a relay on you mic....
@alekseikislukhin87654 жыл бұрын
Awesome, you connected 2 wires,what about other 6?
@BMWRepairsSG2 жыл бұрын
That’s exactly what this video is about. It depends what you want to use the relay for. If it’s for NC connection you use only the NC and common. If it’s the NO connection then only the NO and common.
@jetenginethrust8634 жыл бұрын
Terrible job SMH
@cruizviquez4 жыл бұрын
Thanks for the explanation on this. What I need is to receive a DC signal to activate the relay circuit to send out a 220V signal to start a pump. Can I do it with one of these relays? Thanks.
@markiman744 жыл бұрын
Carlos Ruiz Viquez I think so. I’m using it for a 24v ac main to turn on a 110v injection pump.
@selvapriyan24 жыл бұрын
Your voice very low
@TorPid94 жыл бұрын
i have a 24vac solenoid irrigation valve which i need to power from a 240v outlet, can this relay be used for this purpose?
@BMWRepairsSG4 жыл бұрын
Mahdi Ahli I am afraid you would need to use a step down converter similar to the once I am using in this video
@dylanwhite65394 жыл бұрын
That automatic gain control really fucked with ya on this
@dariopranckevicius12504 жыл бұрын
Thanks!!!! Awesome, simple video!!!
@BMWRepairsSG4 жыл бұрын
Dario Pranckevicius thank you. Do subscribe for more videos.
@hardgamer68444 жыл бұрын
Hey bro I need one help how to connect 200 omms 12v 8pin rely To my battery for auto power cut of can u do a video and upload it u can contact me on Insta (WTF UNKNOWN) u can typ
@fretsadikgetachew27764 жыл бұрын
How you connect the light
@BMWRepairsSG4 жыл бұрын
Fretsadik Getachew , the relay comes with light for indication