How to Wire Up 8Pin relay to base

This tutorial will show you the basic operation and wiring to base for 8 pin 24Vdc and 240V AC relays

[@freytube1]

nice, quick and clear thanks

[@dariopranckevicius1250]

Thanks!!!! Awesome, simple video!!!

[@BMWRepairsSG]

Dario Pranckevicius thank you. Do subscribe for more videos.

[@osmankjr7150]

tysm u really helped

[@catsmeow5566]

Thank you for this! I am thinking of getting the MK2P-I relay. Do you think that would work to connect a 230vac 6.1A pump to a float switch? I need to set it up so that when the float is down, the pump will turn on and then turn off when the float is up. My main issue is that the pump requires 2 hot wires. I've been trying to find info on how to wire this. My brain keeps getting confused on whether I'd need to wire it to be normally open or normally closed. Any advice would be greatly appreciated.

[@umargul5644]

Well done

[@alekseikislukhin8765]

Awesome, you connected 2 wires,what about other 6?

[@BMWRepairsSG]

That’s exactly what this video is about. It depends what you want to use the relay for. If it’s for NC connection you use only the NC and common. If it’s the NO connection then only the NO and common.

[@urbanirrigation]

very clear english

[@lo-fistudio207]

Good brother

[@mosesmakanga6308]

Nice one

[@jaken1319]

So if I put pin 13 and 14 to a USA 110v plug can I plug it in forever ??????? 250V 5A

[@MrAndyloz]

is there a relay on you mic....

[@islamic31399]

Great

[@TorPid9]

i have a 24vac solenoid irrigation valve which i need to power from a 240v outlet, can this relay be used for this purpose?

[@BMWRepairsSG]

Mahdi Ahli I am afraid you would need to use a step down converter similar to the once I am using in this video

[@vfgrfbgrb]

So when it is energized it closes

[@user-hy6lz7ik3l]

👍

[@dylanwhite6539]

That automatic gain control really fucked with ya on this

[@sudeshputran69]

Super

[@nufailfuzoolla3580]

Sir how to check if a relai is good or bad with multimeter

[@vongkea6768]

good

[@cruizviquez]

Thanks for the explanation on this. What I need is to receive a DC signal to activate the relay circuit to send out a 220V signal to start a pump. Can I do it with one of these relays? Thanks.

[@markiman74]

Carlos Ruiz Viquez I think so. I’m using it for a 24v ac main to turn on a 110v injection pump.

[@PBS-nm1uu]

what is the name of the base??

[@josetorree7237]

Wire a ligth or a load

[@lazycarper7925]

please can you help a noob, can somebody tell me if i can wire a 3 pole relay as a single pole, i think thats what i want/need?, i needed a relay to turn on and off from - 24vac,on the coil side-, 240v 35a on the main load , and with out spending silly money i could only find a 3 pole one cheap, thats 35 amps , all i need it to do is when activated by the 24v ac , allow the current of my 240v ac to pass to make the circuit, and that can be just the live or the live and neutral, etc etc if it can be done?, would wiring it so my live splits and goes in to all 3 poles and then out all 3 poles(when activated), to give more current, as its for my mig welder ,(24v trigger), so more amps the better, thank you

[@zacreynolds6045]

I don’t think you’d need to wire the live into all three poles but yes it would work fine for your purpose.

[@sham1234567891]

Good video. Sound level too low.

[@stevewright1272]

How I nuh show where to put the wire's

[@fretsadikgetachew2776]

How you connect the light

[@BMWRepairsSG]

Fretsadik Getachew , the relay comes with light for indication

[@MrPunch05]

Sound is very low...

[@orenbell1645]

Sometimes

[@RobinWhistles]

Pity you didn't wire the rest showing how it can be used.

[@BMWRepairsSG]

It depends what you want to use the relay for, as the points are basically N/O, N/C. e.g. say you need a signal from a pump to activate a motorised valve; you wire the N/O points to the Pump and N/C to the valve or vice-versa.

[@jaken1319]

If I plug one into every outlet will the stupid meter electromagnetic field make it past the closest one?? 😂😂😂😂

[@md.rezowanmiah6656]

sound quality is not good

[@David-ty3yo]

Before doing the job get your microphone working properly

[@AlmightyEye]

Can't hear you!

[@rayjohnson7886]

Poor audio it's going in and out.

[@selvapriyan2]

Your voice very low

[@smittygoodman4071]

Can't hear shit on this video.

[@jetenginethrust863]

Terrible job SMH