Пікірлер
@Itsjustblue247 23 сағат бұрын
I would love to do this one time on my car I know the dealer won’t do it as good as this in reference to the full fluid change
@MrOjmanuel Күн бұрын
Question. If you can answer. When going around 80 mph I feel like going over little bumps, I know that the control arms are going bad but going 70 it feels right. Could be that a complaint when control arms are bad? The tires are good. Thanks 👍
@LILEVO Күн бұрын
I'm tracking down a similar issue, I think it might be my differential. Does the car or seat shake? Does the wheel shake?
@TheChemo562 3 күн бұрын
Will it fit 2010 IS F
@LILEVO 3 күн бұрын
yes, fits everything
@benjiquis3_ 3 күн бұрын
What type of weld process u use tho?
@LILEVO 3 күн бұрын
MIG with argon for steel, tri-mix for stainless
@josephdistefano3755 3 күн бұрын
The most stupidest idea for cars transmission to be changed. When they can make it so easy .manufacturer always try to make things difficult.
@LILEVO 3 күн бұрын
More money for the dealers and manufacturers
@moldovanucalin8827 3 күн бұрын
Same probleme here, I am thinking to add a amplified microphone
@alfredoibarra9825 4 күн бұрын
If no issues and simply doing for maintenance, measure what you take out and fill with same amount of new fluid. For Toyota stick with Toyota fluid and gasket and filter if dropping pans and replacing filter.
@LILEVO 4 күн бұрын
@@alfredoibarra9825 but you don't know if the level inside is correct or not
@jimmyaber5920 3 күн бұрын
Fluid has some fraction volatile component and can be low with no leakage. Also it may not have been at correct level from new or from a service in the past.
@lanceguinn9807 4 күн бұрын
instead of buying lift? is there a jack point from underneath that would work? I'm in the middle of doing my valve cover seals and then my timing belt. So I have plenty of room...
@LILEVO 4 күн бұрын
You can jack the oil pan with a block of wood, but it's not recommended. Otherwise the trans bellhousing maybe.
@chrishamby86 5 күн бұрын
I had my local independent Toyota/Lexus shop do a drain and fill for mine at 150k miles along with coolant and diff. Hopefully I'm good until 200k. I'm still burning a quart of oil every 1k-1.5k miles. It's the only thing I keep a pretty close eye on at this point. I still keep looking for fun at 2016-2017 model years which seem to be the absolute best for the 460
@Itsjustblue247 23 сағат бұрын
If it’s gets worse with the oil consumption could be bad piston rings that’s locked in position which is digging a groove in you engine block unfortunately when this happens you have to replace the short block big job had to do it on mines same problem 2012 Ls430L AWD😢
@chrishamby86 23 сағат бұрын
@Itsjustblue247 I've been using treatment at every oil change and it seems to be slowly going up between needing to add oil as carbon build up gets cleaned out. The independent mechanic says it's pretty normal on this engine and has zero worries. My plan is to keep it for another 50k miles. It's meticulously maintained and cared for so when I do sell it I want it to go to someone who will really appreciate it
@DonWhite-qt8pw 5 күн бұрын
Where did u buy the knock sensor from?
@LILEVO 4 күн бұрын
Mine were fine. Never replaced them. If you need a quote you can contact these guys: bit.ly/JDM-Contact
@gilbertcer564 5 күн бұрын
Just sent my 430 ecu to get repaired for the hard downshifts
@Bwh-rm3py 7 күн бұрын
Could you have re filled the transmission with the hose that you disconnected from the transmission cooler?
@LILEVO 7 күн бұрын
Probably, yes. Not sure if that goes directly back to the pan or somewhere else first though
@nicholascapps2732 10 күн бұрын
Where did you get the supercharger
@LILEVO 10 күн бұрын
Not my car, but watch Ebay they pop up there
@TFTYS_YT 10 күн бұрын
😮
@alanswanson5642 11 күн бұрын
Did it jump the pulley then break?
@LILEVO 11 күн бұрын
Think it just got frayed too many times then finally let go
@mohibdurraani1082 13 күн бұрын
Why not show how to put system in
@LILEVO 13 күн бұрын
@@mohibdurraani1082 it's just a matter of plugging in a few plugs. Nothing much to show
@Court_623 14 күн бұрын
430 not 460 but nice👍🏿
@LILEVO 11 күн бұрын
Got lost in my excitement
@kevincabrera9593 14 күн бұрын
Can u get the front one in ls430 2005 without air suspension
@LILEVO 14 күн бұрын
Yes, I can find one. Give me a little time
@Mastiffman1 15 күн бұрын
I replaced mine without a hydraulic press. Amazon parts 20 bucks. It was a huge job. Broke my 3 ft breaker bar doing it!
@LILEVO 15 күн бұрын
Wow, nice work
@Mastiffman1 15 күн бұрын
Does it knock when you apply brakes or does it go away? I had to add shims to my pads. That helped.
@LILEVO 15 күн бұрын
I think I narrowed it down to the steering rack. It only happens at 1-3mph turning all the way. A nice $2000 repair of course
@nicholasbragg8340 15 күн бұрын
Was this the car from Ohio by chance?
@LILEVO 15 күн бұрын
Chicago
@dodgeking9194 16 күн бұрын
❤❤❤❤Very very nice. Congratulations on such a beautiful machine
@kashiffriends10 16 күн бұрын
Hi just wanted to ask you did you applied any dielectric grease in the gasket?
@LILEVO 16 күн бұрын
I usually use a ight coat of oil
@kashiffriends10 16 күн бұрын
can we use dielectric grease also?
@LILEVO 16 күн бұрын
@@kashiffriends10 No. Silicone grease is best. Dielectric can degrade the rubber
@kashiffriends10 16 күн бұрын
@@LILEVO thank you so much
@Itsjustblue247 19 күн бұрын
You go so hard bro I love it🦾
@LILEVO 18 күн бұрын
Gotta do it right
@YangfanWang-u2m 20 күн бұрын
Super cool video! How did you get it back, could you drive it home right away?
@LILEVO 20 күн бұрын
Yep, luckily I'm only about 10 miles from the port so I crossed my fingers and made it back. The cars clear customs before they arrive at the dock so once cleared you just go to the dock and get it.
@n8dagr881 20 күн бұрын
Landcruiser, best thing to exist for 4x4, tanks that wont stop and will go millions of km's
@LILEVO 20 күн бұрын
It's such a unique truck to drive. You can immediately feel how well built it is
@n8dagr881 20 күн бұрын
@LILEVO i drive a Hj45 which is an old ass landcruiser, built 45 years ago and still going hard mate
@LILEVO 20 күн бұрын
@@n8dagr881 Will be picking up a 95 HDJ81 in about a month at the same port
@n8dagr881 20 күн бұрын
@@LILEVO damn can you send one down australia i need one bad haha
@jhayspins1054 21 күн бұрын
This car is definitely worth it. Ya'll can't be that oblivious.
@LILEVO 20 күн бұрын
Someone got it for 25k
@CaptainTonus 21 күн бұрын
Did you pick this up from the port in National City? I didn't know you could do that
@LILEVO 21 күн бұрын
yep
@kaze5417 22 күн бұрын
any drone on the highway?
@LILEVO 22 күн бұрын
Has stock mufflers and an electronic cut out. Quiet as stock if the cutout is closed
@undagroundrican 22 күн бұрын
So I tried this mic mod but went through all that trouble and now I get no mic. Tried diffrent microphones and no dice. I had an electrician buddy of mine do this with me in case I screw something up. He was puzzled that it didn't work. My radio does not have a gain option nor a option to choose external or internal mic. The internal mic that I removed was the only mic that ever worked. I even bought a USB mic and connected it to the USB of the radio and never worked either..... So frustrating.
@LILEVO 22 күн бұрын
Did you try putting back the original mic? If that no longer works there has to be a damaged trace. Follow or ohm out the two leads back to the main board and I'm sure you'll find something broken.
@undagroundrican 22 күн бұрын
@LILEVO I was able to solder back the original microphone and it worked as before. Guess I'm just going to have to live with this.
@LILEVO 22 күн бұрын
@@undagroundrican which microphone did you try? It's a very simple and universal device. It sounds strange
@jayicg6189 22 күн бұрын
Awesome!
@Crashout107 24 күн бұрын
I just got a 01 ls430 144,000 miles for 2600 needs a paint job & valve cover gasket
@LILEVO 24 күн бұрын
@@Crashout107 good price!
@robertr9372 25 күн бұрын
I think the better way might be to completely drain the pan and get as much out as you can first. Once this is done, measure the amount removed and pump back in the exact same amount and then proceed as shown in the video. Unless I have misunderstood something, you pumped fluid straight into a full pan of dirty fluid? Isn't it better to get all that out first to avoid too much mixing of old and new fluid?
@LILEVO 25 күн бұрын
You can do it this way, but by the time 12-16 quarts go through it's all going to be flushed out anyways. I don't know what happens inside the pan or how much fluid is coming back when pumping it out at the radiator. Is the pan emptying when the car is running or is dirty fluid being pumped back into the pan at all times?
@robertr9372 25 күн бұрын
@ So by removing the line from the radiator, you have interrupted the flow back to the pan. So when you pump back into the pan, it stays clean. For this reason I just thought it’s best to drain completely first. I did this same thing on my 2013 Toyota Highlander and I think this method you’re showing is the best.
@LILEVO 25 күн бұрын
@robertr9372 what does it matter then for the first refill? The pan would be empty after that first purge then you're filling an empty pan. There wouldn't be any dirty fluid in there
@GauseG 28 күн бұрын
Good work man. But please use real jack stands.
@LILEVO 20 күн бұрын
Yea I do if I go under the car at all. This was hard because the jack was where the jackstand would go
@chrishamby86 28 күн бұрын
I have the vlite2 on my 460 and on occasion I wish I had the vline2
@LILEVO 28 күн бұрын
What is missing from it? Voice navigation/recognition, what else?
@chrishamby86 28 күн бұрын
@LILEVO it just is straight Apple Car Play or Android Auto. Where the vLine2 is a stand alone android system that doesn't need a phone. If a vLine3 ever launches I'll upgrade to that if they make one for my vehicle
@LILEVO 28 күн бұрын
@@chrishamby86 Do you have to enter destinations on your phone then? Can't use the touchscreen?
@chrishamby86 28 күн бұрын
@@LILEVO I use the touchscreen. It is the same as the vLine2 but requires the phone connected (wired or wirelessly) just like it would be in a new factory car with AA or CP. The vLine2 is stand alone. It would work (albiet with no internet) if no phone was present. The vLite2 requires a phone to run AA or CP.
@melissawalsh1389 28 күн бұрын
Do you have the next video talking about the torque specs for the head bolts and sequence? I can’t find an actual manual like the one you show in the video talking about the valves to save my life.
@LILEVO 28 күн бұрын
Here you go bit.ly/SDK8-cyl-tq
@martyno8696 28 күн бұрын
Man, I installed a AliExpress decoder that was recommended to me from someone on the forums. I’m beyond happy with it. Same concept as Grom, but it’s Linux based so it doesn’t require updates. It plugged into my audio jack that I tucked underneath my console and the sound quality is just as good. I have an 08’ LS460 btw. Paid about $400. I would bet that they have them for the 430’s .
@LILEVO 25 күн бұрын
nice, have a link?
@martyno8696 25 күн бұрын
@@LILEVO and to anyone who might order this unit, let the seller know whether or not you Lexus has ML audio. Also ask for a video of the installation so you can decide if you are comfortable with the complexity. You have to disassemble the Navi down to the display board.
@CelicAWD Ай бұрын
Ntk is sensors my guy. Nsk is bearings. Ngk ignition components. Nok are seals.
@LILEVO Ай бұрын
thanks. It was a long day
@martycarroll3192 Ай бұрын
Could I reach out to you about my suspension issues? I've got 03 ls430
@LILEVO Ай бұрын
lilevo.com/contact/
@johnfloyd4243 Ай бұрын
You just needed to pull the pin on the timing belt tensioner when you had everything lined up the first time and then turn the crankshaft a couple revolutions and confirm you are still in time. You got off a tooth because of the slack in the timing belt from not engaging the tensioner from the get go. Glad you got it figured out and checked your work.
@LILEVO 29 күн бұрын
@@johnfloyd4243 looks like the tensioner will just pull the RH cam back a half tooth. The LH cam is still a full tooth off after that
@belindahughes321 Ай бұрын
I am working on something like this. Hoping to get some tips and ideas from you guy. I have already purchased two of these chicken coops as they go on sale. How many coops did it take you to do this?
@LILEVO Ай бұрын
this was 3 coops with one or two panels left over. Here's the full length video: kzbin.info/www/bejne/fJW5YX-Cmsp8mrssi=RFO5VXtROOjPhmMf
@Monster_Rancher Ай бұрын
thanks for doing gods work.
@pedrouribe857 Ай бұрын
I have the same car same year but red so please hope this works
@LILEVO Ай бұрын
Unfortunately the project never got traction and wasn't too popular on youtube so it's for sale: bit.ly/ES300-For-Sale
@OGBarry16 Ай бұрын
I’ll buy it right now
@LILEVO Ай бұрын
sold for $25k a couple weeks ago
@carrichcashpoor Ай бұрын
Where is this yard? I'd buy parts from this
@LILEVO Ай бұрын
They crushed it. Was up in Riverside area
@Rey-uw8my Ай бұрын
That's awesome dude! Congrats... super rare transmission and supercharger. If you have any videos of the swap process, you should post them, it would be amazing and greatly appreciated by many in the 1MZ-FE community
@martyno8696 Ай бұрын
so i ordered the front lower control arm, 2013-2017 version, and the ball joint shank is much shorter than the OEM that i took off. Are these not interchangeable as well? I thought I read that they were on the write up you did on ClubLexus.
@LILEVO Ай бұрын
would need to know what parts you ordered. the part numbers should match with the ones in my descriptions. AWD and RWD are different for the front arm. could be that
@martyno8696 Ай бұрын
@you’re right. I screwed up and ordered the AWD fronts. I appreciate the reply. Hope your control arms are all still holding up well.
@LILEVO Ай бұрын
@@martyno8696 so far so good! Check out my new venture if you need discounted oem parts: bit.ly/Lexus-Parts
@Everyday_Richard Ай бұрын
Do you know where to find the site glass for hydraulic fluid. Mine has a crack and leaks out all over. I have no idea were to find part number. Have search every term and word i can think of on KZbin, Google, chatGTP. No luck on info for these older units. You're videos are extremely helpful. Thank you!
@LILEVO Ай бұрын
bit.ly/sdk-gage-oil
@LILEVO Ай бұрын
The fix: kzbin.info/www/bejne/rWq0hqiVorOFbLssi=KgP82sP2MvkmSxxy
@Lowcountryinshore843 Ай бұрын
How to fix it I thought it was the seatbelt ecu ?
@LILEVO Ай бұрын
kzbin.info/www/bejne/rWq0hqiVorOFbLssi=KgP82sP2MvkmSxxy