Ender 2thar up doen poper fixe mather borad ok loose contacte after checking ssp hp lp one ny ok sir
@marioe55809 ай бұрын
Hi there, I have the same problem... cant bind the new EXV module in a CGAM120 unit... it seams it need a patch or sometheing else... are you familiar with this problem ? any help where I can find that software patch ? thank in advance
@lacostaz4119 ай бұрын
Do you work for MLN ?
@qomco Жыл бұрын
Great video
@tanyamanhid625 Жыл бұрын
Hello sir. What is the problem if CB3 fuse is trip and alarm of T051 and T055?
@shanegreen268 Жыл бұрын
Thanks for sharing your knowledge. Great video
@prowesstv Жыл бұрын
You had the micron gauge on the wrong end of the removal tool, when you valved off it was not reading from the system so the low volume is what caused the drastic rise in microns.
@SoutheastHVAC Жыл бұрын
Just found your channel. Love the commercial videos!
@evelyn367 Жыл бұрын
Good job and explanations, looks like a computer server room thanks
@joshcara5345 Жыл бұрын
Any idea how to adjust humidity set points alarms? I get the input from the unit, so its not something i can modify from my BMS system.
@khalidsr1 Жыл бұрын
Could you please explain how to operate chiller carrier 30Gt510568.( gt 350 ton) Thanks 😊 and God bless you
@khalidsr1 Жыл бұрын
Great job and good luck to you 👍 thanks 😊
@PBS-nm1uu2 жыл бұрын
bad angle on the camera
@aleckofunk75642 жыл бұрын
Need some Fjall raven pants bruva! Built in slits where the car Bart oversized pads can fox i love em. Wear them everyday. They like 200 but worth every penny
@toufikmatib98552 жыл бұрын
Hello thank you for sharing can I have the link for the app please. Many thanks
@mrgeraldbrent2 жыл бұрын
Hey man. Been a year since your last post. Just checkin in to see if you're doing alright.
@johnnyroxannebautista20632 жыл бұрын
it's high pressure sensor. the switch is only have 2 terminals
@juhDaddy092 жыл бұрын
Good video man!
@babaolowo352 жыл бұрын
Thanks 👍
@turkeyslayer632 жыл бұрын
How to convert a Variable Air Volume (VAV) unit (16th digit of the model number is a 2, 3, 4, 5) to Constant Volume (CV): Remove power from the unit before you begin this procedure. 1. (IGV units) The IGV must be mechanically locked open. The unit will no longer control it. 1. (VFD units) The VFD must be programmed so that the minimum speed is 60 HZ. Without COMM (LCI, TCI or BCI) 2. Remove the wire harness from the RTRM J4 to the RTAM J2 (wires W68-W71). Discard the harness or save it in case the unit needs to be converted back to VAV. 3. Unplug PPF13 from the RTAM (wires W63-W66) and plug it on to RTRM J4. 4. Restore power and test. The unit is now Constant Volume and requires an appropriate zone sensor or conventional thermostat for operation. With COMM (LCI, TCI or BCI) 2. Remove the wire harness between the COMM J2 and the RTAM J2 (wires W68-W71). Discard the harness or save it in case the unit needs to be converted back to VAV. 3. Unplug the J3 plug from the RTAM (wires W63-W66) and plug it in to Comm J2. 4. Restore power and test. Note: If the unit has LCI, the LCI-DAC will have to be replaced with LCI-SCC or LCI-X. Otherwise, the unit will not control properly.
@MysticHaunt2 жыл бұрын
Jesus, 60k btu total for a room that small? Is it oversized?
@hvacworld74212 жыл бұрын
It is going to become a server room. It was spec out for a 5ton.
@berniecapal13082 жыл бұрын
Follow up to last comment. I have the cable that connects to J10 plug , did you mention connecting to J4 plug some how?
@hvacworld74212 жыл бұрын
I made a cable for to allow me to connect it to the older RTRM boards that have the J4 plug. Out of my TD5 I split the j10 plug and added a j4 plug. I also made a split cable to use incase there was something already plugged into the j4 on the board. It works great
@berniecapal13082 жыл бұрын
Thank you brother
@mikecorral23582 жыл бұрын
I would love a wiring diagram of your J4 harness conversion on your TD5 Cable
@berniecapal13082 жыл бұрын
Thanks for the video, I have a question if you don't mind. I just picked up a TD5 display but I don't have a cable or know the connection points to the board, could you give me information about what board to use and where it connects to the board? Thanks in advance brother.
@fkdeazevedo2 жыл бұрын
where can I get a fuse popper
@hvacworld74212 жыл бұрын
The one I use is the Supco BRKPRO
@andrewmcdonald45192 жыл бұрын
Good job man very impressed I work on these VRV systems all the time and I learned a lot from u, like how u tested the board for a ground fault as well
@amedhossain60322 жыл бұрын
Sir, your video is quite dark and can't see properly, and also make the camera closer to the unit..
@anvarshaikh37932 жыл бұрын
Good information brother
@autolancegega5992 жыл бұрын
Nice video,Thanks for uploading, I am new to hvac, i am from the industrial electrical feild, but I am learning a lot , thanks to techs like you.
@karaors89703 жыл бұрын
👍🇹🇷🤳🛠️
@SombraLocs3 жыл бұрын
Have you worked on the Daikin AGZ?
@hvacworld74213 жыл бұрын
No, I have worked on the other daikin air cools and mcquays but not a AGZ yet.
@Stormchoirs7 ай бұрын
I just did a startup for a AGZ today.
@acechoice453 жыл бұрын
I was surprised that pump seals wasn't smoked
@hvacworld74213 жыл бұрын
I know, had another job shortly after where they left the pumps on for days after the freeze and the loop was completely dry. Couldn't seven put you hand on the pump and it was still good after filling up the loop.
@acechoice453 жыл бұрын
Stay bright 8 can take up to 500F of heat and 3500 psi of pressure I use it sometimes on RVs and TXVs and I never had a problem. Do you ever use silver solder for certain jobs?
@hvacworld74213 жыл бұрын
All I use is sil-fos for copper to copper,, Silvaloy 560 for copper to brass or steel, and al822 for aluminum. It's all worked out for me. Heard good things about stay bright 8 but have not used it yet.
@richardbartlett69323 жыл бұрын
Tried to watch but gave up with the stupid music.. Truly dreadful totally unnecessary
@hvacworld74213 жыл бұрын
Ok, thanks
@tonybasham71413 жыл бұрын
I noticed the comment you made about setting the min HZ 60 . You have a VFD that still can be used in a Single zone application do not need duct static pressure . The VFD will ramp up and down base on the need . Fan only it run at min , Econ start to ramp up , 1st stage cooling , 2nd stage , 3rd stage up to 100% VFD or Heating will be 100 % VFD . Email me , Be glad to help I’ll send you my cell number
@hvacworld74213 жыл бұрын
Thanks, thought about staging the drive on cooling demand but will get a little more complicated. Could not see how to do so with out running wires everywhere.
@tonybasham71413 жыл бұрын
Need to change from VAV zone to Single zone . bypass the RTAM module and Change the VFD setting. Have a Trane Factory setup for this unit or you can installed a Trane VAV T-stat to keep as a VAV system . Note : the unit will drive VFD to 100% in Heating mode . Have a relay on this unit that you can wire to open the damper 100% . If you would like some help email [email protected] 23 years Working for Trane commercial and industrial in Dayton Ohio .
@roqueherrera26923 жыл бұрын
Shoot one in the day BRUH…..
@hvacworld74213 жыл бұрын
I know, had to get an early start that day.
@kennyw74533 жыл бұрын
Looks like maybe a two-pipe dual temperature loop with summer/winter changeover.
@hvacworld74213 жыл бұрын
Yah, that's right. Old school stuff and a big huge mess.
@LadariusCapersOfficial3 жыл бұрын
@@hvacworld7421 Big Air Conditioner Machine
@kennyw74533 жыл бұрын
Great channel and good video. Just curious if the RTU is configured for VAV and you have zone dampers, if you configure the unit for CV don't you need a bypass damper to control static pressure?
@hvacworld74213 жыл бұрын
Thanks. Yes, you are correct. The site had about 5 zone dampers. I removed all the actuators and open all dampers 100%. Then I dropped a thermostat wire down in space and installed a thermostat. After doing so I changed the setting on the drive to a min 60hz. Site was an open plenum return. Works perfect. It was the correct set up for the site however not the correct set up for every site.
@syedbasheer82103 жыл бұрын
Nice channel✅✅
@hvacworld74213 жыл бұрын
Thanks. Will have more videos coming soon and starting some HVAC tool reviews as well.
@hilikus45303 жыл бұрын
I use the same vacuum setup. Love the Appion micron gauge. The new version of the app is way better than it used to be.
@hvacworld74213 жыл бұрын
I agree. The appion is by far the best gauge I have used.
@Blueblurr1123 жыл бұрын
Great video brother. Thanks
@hvacworld74213 жыл бұрын
Thanks
@MRICE-qe4sv3 жыл бұрын
Good video.
@hvacworld74213 жыл бұрын
Thanks
@ReliableHVACR3 жыл бұрын
Nice work 🤙🏽
@MRICE-qe4sv3 жыл бұрын
Nice work. Are you in Houston? Who do you work for if so?
@georgebrabec17493 жыл бұрын
Well most of the time, depending on the degree of ground/burn it will take out the other compressor. It the same thing as replacing a single compressor without cleaning up the system. You may get lucky, at least I hope so !
@hvacworld74213 жыл бұрын
Totally agree. It's always recommended that you replace a trio or tandem when one compressor is a burnout. However most customers will not want to pay for that. Luckily I did an acid test and it came out negative, however you never know if there was a mechanical failure and shavings such as from the bearings got in the oil.
@georgebrabec17493 жыл бұрын
Great troubleshooting, but did you leave that circuit active or off on the options program ?
@hvacworld74213 жыл бұрын
Thanks. Left it active. The building needed that additional circuit active. Chiller was calling for compressor 1 and 3 to engage. However only compressor 3 was running.
@MrTahoeman83 жыл бұрын
Bro, nice video however music is too loud and distracting
@hvacworld74213 жыл бұрын
Thanks for the heads up. Noticed the same after I did the edit. No longer posting videos with music in the background.
@kcomfortsystemshvac70603 жыл бұрын
Nice information,,,,,I have one question ,,,any time you change compressor ,,,you need to put in recovery mode ? I suppose it need to close the all the valve too ? If I am wrong,,,,?
@hvacworld74213 жыл бұрын
Yes, in recovery mode, it will allow the system to open up to recover the complete charge. This way you can also pull a proper vacuum and weigh in the total charge. You do not need to close any valves on the system.
@dmvhvactech3 жыл бұрын
This is amazing stuff, thank you. I'm a current residential tech, planning to transfer into the same work you do. Can you do a video on how you got to working on this size equipment, whats the progression like?
@hvacworld74213 жыл бұрын
Thank eastcoasthvac, Commercial HVAC is a whole different ball game in my opinion. That's a good idea, and I will do that. My best recommendation is to possibly get into a union shop. You have the opportunity to be in the best school being taught by real techs.
@dmvhvactech2 жыл бұрын
@@hvacworld7421 Hey brotha, I actually got into the union and start with a commercial/industrial outfit in a few weeks. Looking forward to being exposed to all types of new stuff and learning. I've only ever worked in residential shops with like 5 techs, now the place I'm going to has like 150 guys with all different types of teams (chillers, vrf, controls). Had to take a pay cut, but within a few years I'll be in a better spot and my current benefits are so much better. Hope all is well with you
@hvacworld74212 жыл бұрын
Good deal man, union is the way to go. Smart career move. If I can give you any advice at all is to listen, read, and love the trade. If you do that I am sure you will go far places rel quick. Also never turn down any job no matter what equipment it is.
@dmvhvactech2 жыл бұрын
@@hvacworld7421 For sure, thank you for the advice.