You didn't mention if you machined the head gasket mating surface to ensure it doesn't fail again
@themerianofamilyАй бұрын
Thank you for your video! I have new lights & will try using yr posting. Thanks again!
@kamilmitnick9539Ай бұрын
Super job lads. There is no much videos about Jeep Commander. This one is awesome 👍😎
@moshet8422 ай бұрын
How did you clean the deck?
@laccywaccy37432 ай бұрын
Step 1. Get a 2011 Tiguan. Step 2. Replace the headliner on a 2011 Tiguan. You're done!
@holoduke51a2 ай бұрын
I just completed the job. Order 4 ia ebay for arround 30 bucks. Took me about 45 minutes to replace all 4 of them. Easy job. Regarding the screws. I could not get them all tight. But it does not really matter. As long as you have the one close to the lever its fine. Use some hot glue to fix the rest.
@unforgiven101inc3 ай бұрын
I think it'd be cool if you told everybody what size of bolts were
@Flyingbackslapp3 ай бұрын
where did you find the screws and the bit for the drill?
@d.l.horton20934 ай бұрын
Didn't get to hear it start.
@22jeromebettis4 ай бұрын
Is this the same concept for all commander engines?
@dagger41465 ай бұрын
Did you ever get it running ? Was that a used piston and rod assembly ?
@danlane53505 ай бұрын
Can you provide the link where you purchased the handle kit? When I look on Amazon and Ebay they say not compatible with my 2006 76th Anniversary Edition
@steveholley95085 ай бұрын
Before doing all the Body Works shouldn't you check the motor see if it will run
@michaelt13495 ай бұрын
Stopped watching after 45 seconds. The background music adds nothing and only makes it harder to hear what you are saying. Thumbs up if you lose the music.
@joelpc245 ай бұрын
Do you have the link for where you ordered that doorhandle?
@philliptaylor59815 ай бұрын
The guy doing most of the talking needs to talk half as much.
@meno22036 ай бұрын
I also have a 2009 corolla, with a cylinder 4 misfire and low compression in cylinders 3 & 4. Thank God for the both of you 🙏🏿, HUGE help 👏🏿👏🏿👏🏿👏🏿👏🏿👏🏿 I also found a bad head gasket.
@JonathanBoone-dy4cr6 ай бұрын
Give tire size your poor an explanation and description😢
@marekszcz16 ай бұрын
Hey guys, great video Thanks, Tim & Ben
@chasecrockett19476 ай бұрын
Next time remove cross brace is only 2 18mm nuts much easier
@jerrythomas68726 ай бұрын
Thank you guys for this video. I have previously replaced both headlights but a few months ago I hit a deer and it busted the drivers side headlight assembly. Your video helped me make quick work of the project.
@travisfreeman18287 ай бұрын
Did you get the speedometer video yet?
@maxxmich7 ай бұрын
always hnplu the connections... or u won't have any working fog lights....
@maxxmich7 ай бұрын
those r non reusable push robots.. need to use new ones
@maxxmich7 ай бұрын
need to polish the fog lights......
@RonStanek8 ай бұрын
Don't those fender wells just snap off, after you remove the plastic pop out pins around the bottom of the fender? Would make it easier to get to the last bolt, by the blinker/marker light. The right tools might help also.
@tonyhippensteel38054 ай бұрын
Yes. Taking the inner fender liner out saves a lot of headaches they were experiencing
@Ntynn99998 ай бұрын
Took me over a year to finally decide to do it since a pheasant blew out my passenger side. Got tired of changing bulbs when it rained. Thanks for the how-to!
@porterdevane60209 ай бұрын
Need a video on how to take this piece out
@poitevienphilip10 ай бұрын
Good video, but you need to move that camera to better see the mechanical work of that car
@gingerproject888network610 ай бұрын
I didn’t know how cheap quality the handles are. It broke so easy after one moving day. I rather not have the handles sticking out.
@TheGuruStud10 ай бұрын
These engines are trash
@hotjoshpeck Жыл бұрын
Thank you!! Big help!! I just bought a 2008 Jeep Commander for $500 and replacing the head gasket myself Ill save tons!!
@wasifshah4491 Жыл бұрын
How much time it take for all procedure
@joshvaldovinos Жыл бұрын
Tire size ?
@garbageman1917 Жыл бұрын
I've been fighting this problem for a week now. I'm not looking forward to this fix
@BIONDIEST Жыл бұрын
so how do you know if its the valves are good or not? how can you tell if the piston rings are good or not? how do you know if the block needs to be machined or not?
@BIONDIEST Жыл бұрын
from what ive read online this engine should have been recalled. ive taken mine to Toyota and they said it was fine to drive. yeah right. 180k i have a misfire on 4 and im thinking best case scenario it needs a new head gasket. ive also read that the cheaped out on the piston rings on this engine. i guess i should look up how to replace those too
@DonziGT230 Жыл бұрын
5:38 Dang, I have a lot of tools, but no 11 point sockets so I guess I'm stuck.
@joeblow1238 ай бұрын
4.0 engine uses standard bolts. old design from american motors from the 60s. 7/16 socket is what really fits them.
@DonziGT2308 ай бұрын
@@joeblow123 It was a joke; he said "11 point sockets" when he meant to say 11MM sockets.
@UFGator1972 Жыл бұрын
When you need to replace one, it is a good idea to do both sides.
@brosagt3822 Жыл бұрын
Very bad man
@almazm699 Жыл бұрын
Thank you man I got the same problem I appreciate it for posting this video
@kevindavis6640 Жыл бұрын
I have yet to find anything on replacing the ignition switch/coil
@toanigamboa4483 Жыл бұрын
Link for where to purchase quality head gasket kit for Jeep 5.7 HEMI??? Thanks
@dalestafford6268 Жыл бұрын
Thats crazy... same exact problem in my 2007 5.7 hemi...
@dalestafford6268 Жыл бұрын
From the head and piston
@jaytank31 Жыл бұрын
I have a charger with same issue. How bad was cylinder did you just replace piston, rod and head
@jjginnard Жыл бұрын
You didn't post a link on ebay for the lights?
@stacyherod7551 Жыл бұрын
He'll you skipped over all the work and basically didn't show anything about actually how to do it