Jesus Christ.... Use match man. Nice Kero though

Shadt not in properly

Hi~ thanks for the awesome idea! I also have space restrictions. Did you ever end up mounting the table onto the Rigid miter saw stand? Could you share your final results? I also use the 10” craftsman table saw table as my welding table. Looking for solution for storage. This sounds like a perfect solution. I thought about building my own, but material alone will cost me more than this stand.

The drive pulley is way too small

Great VIDEO Sir...Exactly what I needed to see. Thank you so much now I know what to do.

sounds like the cleaning pin part is missing. Be careful you don't unscrew it all the way - it might spray pressurized gasoline out, and cause a big fire! Get it properly serviced. By the way I like my SVEA better that the propane canister stoves of today, even if it is somewhat heavier. SVEA always can provide plenty of heat, even for bigger pans, like a 12 inch cast iron skillet. It also runs great in very cold weather that will stop the butane/propane stoves.

You ship it to me in Kansas and I’ll take it 😂

Combination. Absolute rod knocking, but also lash adjusters/rockers rattling as well.

What was the problem? Because i am having the same problem😢

hello where can i buy one paire online

The FPS Of Your Video Format Just Makes It Appear Slow; Acts Like A Strobe Light Effect.

Aw, got away. that's okay though, probably for the better. What a good pup. Please give Wilton head scritches for me. ❤

Good explanation but how much mm. He put them..

I would have just put the Trailer in back of the Truck.

How to buy tweeter bx8 carbon in Nigeria

How to Buy bx8 carbon toweeter In Nigeria

We have blades that may fit your mower. We're happy to offer you the product completely free of charge in exchange for a video review. Are you interested?

Nice lantern, thanks for sharing.

I will try this

Can understand what youre talking....your mumbling

I've got a Casio unit aux into a Bluetooth dongle & mounted a USB charger. The only thing that sux is having the BT dongle sticking out the dash. I'd like to mount it all inside the tape deck. I think the power for the tape drive motor might be a good power supply for the BT dongle 🤷

Why worry. Just get a new joint.

Sweet hack! Thanks for the info!

Did it come with the shade/globe?

I used a hacksaw, my truck is basically at end of life anyway. Still took an hour.

What type of car are u in this video?

I’m working on my friends Honda gold wing 1990 special edition and the back brake piston are bad and not moving freely and one of them is like welded in and not moving I believe they heated up and expanded so in order to fix that is to get new piston’s and new piston seals and do a full overhaul on it to make them work properly

I started laughing when you said “ better start building some shelves “ That’s the realest thing anyone’s ever said 😂😂😂

It looks like these parts have seen no maintenance since the bike left the factory. Maybe get a good workshop manual, it will guide you re service intervals, lubricants etc.

I got some hose the same size and a adapter ti make it a little longer and it makes a.world of difference putting it on

Which part are you saying was the problem?

Timeing chan slide rail woren out leting timeing chan slap against the block. Have Sean chans rub hole in the he block

I try to get my dogs amped up about the squirrels in the back yard but they never seems to notice them lol

Two thoughts; you could rotate that shaft 180 degrees and most likely it will remove half of the movement in it. Or you can oversize the holes and install an oversized shaft, or oversize them and install bronze or oilite bushings in all four holes and use the new shaft you bought.

New engine a little after I heard that noise in mine 😂😂

I sure hope that's not my issue. I can't afford to have that fixed and I'm not skilled enough to try it myself. I have a video up if anyone wants to hear the knocking I'm dealing with. I know it's not the oil nor starter as they both have been replaced.

Hello, I have a problem with the idle speed, it only goes from 800 to 1400 rpm, it works poorly for a while and then it only goes back to 800 and works fine for another hundred miles and so on. Any ideas? thank you.

Trying is better than LOOKING at it , not like my home boys !!

would have been real nice to actually hear what you are saying brother

It helps if you aim the zerk fitting where it can take grease😊

Oh you just replaced last year…… They usually last 50,000 miles if you use Motorcraft or MOOG K series. And you grease them regularly. Cheaper ones don’t last that long

Yes, Put a jack under the control arm with the torsion spring. Then pry up on the tire. Test the uppers with the wheel off and the suspension extended. Try to pry down on the upper. Odds are you need all 4 Also check the idler arm. If it moves when you lift up and down, it’s loose. Pitman Arm is less common, but still common. They fixed the design in 04

Little elbow grease some duct tape ... Good to go!

Methheads had a field day on that one.

Class!!!! To go with the thumbnail.

You missed the coffee mug

Too funny, finally an honest realtor. 🤣🤣🤣🤣🤣

I can understand to a point that whatever his reason is for scoping out the property.This is mild compared to other channels on KZbin and TikTok.Maybe he is on scavenger hunt or a salvage expedition.I myself have been on many occasions in these situations.One person’s trash is another person’s treasure.

A$$ hole 😢😢

Didn’t your mother teach you any respect 😢😢