Жыл бұрын
Пікірлер
@MISERSTYLE 5 күн бұрын
Will this fit a 2022 f150 XLT with a 2.7 Ecoboost?
@juggernautusa 5 күн бұрын
Yup it will!
@kneepayne 16 күн бұрын
Can confirm the install steps are spot on. I just put these on my 2016 (Roadtrek Zion). They are much brighter, but I did run into something the first day using them. When the headlights are on there is a loud humming sound, like a fan running. I don’t know what is going on, I may have to restore the original headlights until I can make sense of this.
@juggernautusa 15 күн бұрын
The headlights do have fans built into them. If there is a particular bulb that is abnormally loud we can send you a replacement. Just shoot us an email at [email protected]
@djmer28 Ай бұрын
Do these headlights for the 2022 Ram ProMaster have a resistors to prevent interference with electrical issues or indicator on dashboard ❓
@juggernautusa Ай бұрын
Yup they are built in. They mimic the OEM bulb resistance and don't throw any dash warnings
@kevinmacias4411 Ай бұрын
How much for something like this , I’m a local with the same truck literally looking to do the same exact level kit
@juggernautusa Ай бұрын
Send us an email at [email protected] and I can get you an estimate
@abelvargas9307 3 ай бұрын
Will these fit a 2wd 2017 f150
@juggernautusa 3 ай бұрын
Unfortunately these won't fit 2wd trucks
@GoldenJohn13 8 ай бұрын
1'75" or 2" look same. For the cv axel wich best??
@CantTalkImRiding 10 ай бұрын
Has there been an update to this kit that does not use the red gasket maker? I saw another video that has white brackets that go between the socket and the LED bulbs.
@juggernautusa 10 ай бұрын
Yup we have updated our kit with direct fit OEM bulbs. No need for gasket maker or any white adapter. Here is the video for our updated kit with the new direct fit bulbs: kzbin.info/www/bejne/pHaqpYuujJWFfck
@juggernautusa 10 ай бұрын
Also you can purchase them here: juggernautusa.com/products/ram-promaster-led-headlight-upgrade-kit
@Jason-vh6nr Жыл бұрын
What happens if you plug in the wrong way positive and negative and negative to positive or is that even
@juggernautusa Жыл бұрын
The headlight bulbs will line up with the housing so that it is always plugged in with the correct polarity. Of the fog lights don’t light up when power is sent to them, just unplug the connector and rotate it 180 degrees. No damage will be done if they are plugged in the wrong way!
@123thekman123 Жыл бұрын
What orientation is the LED chip facing? Up, Down or sideways?
@juggernautusa Жыл бұрын
The leds face sideways
@steveg309 Жыл бұрын
I was struggling to get the low beam installed until I saw your tip about putting the bulb in the hole fist, then push the socket in over it. That worked, as opposed to my first attempt at pushing in the bulb and socket in while connected together. Thanks!
@juggernautusa Жыл бұрын
Glad it helped and thanks for your business!
@Paul-xz1tg Жыл бұрын
Do you have skid plates for the batteries ?
@juggernautusa Жыл бұрын
We do sell ones for the lithium battery pack vans: juggernautusa.com/collections/ram-promaster-fiat-ducato/products/volta-lithium-battery-pack-skid-plate-for-ram-promaster-winnebago-solis-travato-thor-sequence
@ninja63639 Жыл бұрын
What did you guys come up with for frame end link separation?
@verdexj160 Жыл бұрын
Too bad this is no longer available.
@marioprzepiora Жыл бұрын
Page not found. Can not order.
@kwekalu11 Жыл бұрын
I want to upgrade my ProMaster 2023 too but I can’t find any led lights that fit 2023 let me know if you find one
@84miguelrivera Жыл бұрын
What led lights reference I need what number for low and high thanks 👍
@TimotheosEnterprisesMedia Жыл бұрын
Are these lED lights heated to help melt snow and ice off of the lenses?
@juggernautusa Жыл бұрын
They don't put off as much heat as the stock halogens but definitely do put off enough heat to melt snow and ice.
@TimotheosEnterprisesMedia Жыл бұрын
@@juggernautusa very good, thank you..... I need to switch to LED at some point
@bamuz Жыл бұрын
6:08 bbbbbrrrrooooooo I’ve had my promaster for a few years and never knew this CLUTCH like and rated for that!
@ranig2848 Жыл бұрын
Is it possible to replace the bulbs without removing the entire headlight housing?
@juggernautusa Жыл бұрын
I’m sure you could. Honestly makes it much easier to just pull the whole assembly off. Pretty tight behind the drivers light.
@bamuz Жыл бұрын
You can but no point in fighting yourself to get the bulb in
@fabguy276 Жыл бұрын
How much uptravel do you have with the coil overs set up the way you did it? I was think about doing a similar setup. Any chance you could do a video on the setup showing the upper and lower shock mounts? There is not much information on this type of setup on an XJ. Thanks
@juggernautusa Жыл бұрын
We can definitely post a video. So it has 10" travel shocks that are mounted about 4" back from axle center so the total wheel travel is around 11.5". The up-travel on the shock is set at 4.5" so little over 5" at the wheels.
@fabguy276 Жыл бұрын
@@juggernautusa thanks for the info and prompt response
@jareye13 2 жыл бұрын
red gasket maker holding bulb in place.... interesting solution
@vortexprintworks7605 2 жыл бұрын
amazing intro lmfao
@mm16046 2 жыл бұрын
Do these ever burn out?
@juggernautusa 2 жыл бұрын
Haven't heard of any of ours burning out. LEDs have a very long life compared to the stock halogens!
@ericly1735 2 жыл бұрын
Where Can I get those bulbs?
@randomlybro 2 жыл бұрын
Will an error light show on the dash?
@hummerguy 2 жыл бұрын
For the Humvee do you have to change the spindle nut to CTIS ones?
@1brotz2 2 жыл бұрын
Interesting..
@1brotz2 2 жыл бұрын
I run SUPERAIR CTIS system on my explorer
@gilhildebrand7065 2 жыл бұрын
I installed this myself and didn't have access to a floor jack. To hold it in place during the install, I found two helpful tricks. The first was to first screw in the extra nuts (for the stand-off kit, not shown here) instead of the locking nuts on all four sides. The regular nuts are a lot easier to screw on and I was able to get it in place quickly this way. Then, I went side by side and unscrewed the regular nut to replace it with the locking nut. The second trick was to swing my leg directly under the generator and use the inside of my knee to hold up the plate. This got tiring fairly quick, but was just enough time to get the regular nuts in place.
@juggernautusa 2 жыл бұрын
Oh nice! Sounds like a great way to do it!
@Stigman11 3 жыл бұрын
Will send you an email soon, this is exactly what we need.
@derherr65 2 жыл бұрын
CTIS system don't show on their site anymore... are they still offering them?
@Stigman11 2 жыл бұрын
@@derherr65 I dont know, hope he can give a answer
@lovematters7122 3 жыл бұрын
Is that generator hanging below the rear wheel axle? How much ventilation is the generator able to get?
@Tork-kc5vg 3 жыл бұрын
Great mod! But you covered the oil drain plug making more work to a oil change. Access to the drain would be perfect
@juggernautusa 3 жыл бұрын
The next batch will have access to the drain! Will be ready to ship early September!
@jameswhritenor2458 3 жыл бұрын
Nice!!! on my list
@alextrainor2552 3 жыл бұрын
Can you put this on a jeep?
@clashofclansshield8583 3 жыл бұрын
I can’t get much off your web page but I want to put a ctis system on my 2006 M1165. If you develop the hardware, please post a new video. Keep in mind, water proof everything. For some reason, we HMMWV owners like to drive under water if we have an extended snorkel and exhaust pipe. Lol. It is the closest thing to a submarine that we get, I guess. Lol
@MatthewLeonardco 3 жыл бұрын
Oh nice! Yeah I pulled from the website for a bit. Definitely gonna make it waterproof! Lol at the submarine comment
@cowboynidaho 3 жыл бұрын
Nice system I am currently designing a ctis for live axles. Is you system just the computer and software or is it the hardware
@juggernautusa 3 жыл бұрын
As of right now it is the computer and the software. Been busy with other stuff. Would love to chat about partnering up. Shoot me a message at [email protected]
@rohitsvs1 4 жыл бұрын
Awesome System & programming!🤩👌🏻 Some suggestions- 1.Make the Screen lil bit smaller & design the outer casing like the Spod touchscreen. 2.Place the connectors on the rear of screen so that it can be dash mounted for a cleaner factory look. 3.Make it Bluetooth,wifi compatible with Adroid,ios App so it can be controlled while from outside the Vehicle like the JW speaker J3 headlights. Your product has revolutionised the CTiS system! To get this product blow up the internet & some good bussiness get in touch with Predetor Inc,Mod Mafia,Mil-Spec Automotive,Xtreme Hummer performance,Chris Fix!😁
@juggernautusa 4 жыл бұрын
Thanks Rohit! Love the feedback! Gonna paste my response to your feedback on Facebook! Please let me know if you have any more ideas!
@juggernautusa 4 жыл бұрын
From out facebook convo: 1. Yeah the plan is to have a panel that swaps into the existing CTIS panel. I do like the case. Definitely need to make water-proof for the open tops. 2. The connectors will be hidden for the final products. 3. The control device does have bluetooth and wifi. Definitely need to build an app to control remotely :) Have toyed with the idea of having the screen just be a removable tablet that conects wirelessly to the control system. 4. Yeah waterproofing is definitely on the list! 5. I will definitely add some animations :) Working with a designer to make the UI really clean. Please let me know if you have anymore feedback! Also feel free to shoot me an email at [email protected] if you wanna chat more :D
@rohitsvs1 4 жыл бұрын
Juggernaut USA Great!❤️
@johnnyringo6533 4 жыл бұрын
Hey how much is this and where to buy it? Can you post a link to a page for pricing and purchase? Thank you!
@juggernautusa 4 жыл бұрын
Yeah definitely: www.juggernautusa.com/product/juggernaut-ctis-2-0/1?cs=true. Also happy to work out a screaming deal with you since you would be the first purchaser!
@marioprzepiora Жыл бұрын
@@juggernautusa did you stop selling the CTIS? I was looking to get one
@juggernautusa Жыл бұрын
@@marioprzepiora I pulled it off the site while I work on a better version that will be controlled by an app on your phone.
@marioprzepiora Жыл бұрын
@@juggernautusa awesome. Any ideas on the cost?
@51coronet 4 жыл бұрын
Nice! Are you on the hummer network forums? You have some fans there already with questions.
@juggernautusa 4 жыл бұрын
Hey! Thanks for the heads up. Hadn't logged on there today. Will start responding to questions!
@BigHesh81 4 жыл бұрын
Awesome product and ideas! Have you had any cold-weather testing done on your system? (In Canada we see temps down to -40)
@juggernautusa 4 жыл бұрын
Thanks! I haven't yet but has survived the Colorado mountains. Is that -40C?
@BigHesh81 4 жыл бұрын
@@juggernautusa (-40c is the same as -40f ) Thanks for the quick response! Consider me subscribed!
@juggernautusa 4 жыл бұрын
@@BigHesh81 🙈🙈🙈🙈 thanks for the info! Ha ha. Awesome man! Let me know if you have any other features or ideas for the system!