Can it work using nabu-casa cloud instead of the local Faster Whisper/Piper?
@OGKenGКүн бұрын
What about plugging in a speaker to the headphone jack?
@joeneubauer3208Күн бұрын
Thank you Chris nice tutorial! Has anyone tried this in comparison to building this on the Raspberry Pi 2 W? I built one of these satellites using a ReSpeaker hat with the P2W and it was pretty laggy and not as accurate as I hoped. Has anyone built both and does the ESP32 version function better? I assumed the Pi 2W would perform better.
@JoshFisher567Күн бұрын
Their default YAML on their wiki isn't great. I wrote a new version using Microwakeword. It worked pretty well but on the HA forums there is some yaml that turns the device into a media player allowing you to control the volume. It also does timers and uses the XMOS more from my understanding. It's in the dedicated thread for the respeaker lite. I highly recommend trying it out. The 2 USB ports are because there are 2 firmware types, on for i2s like in this video and another for PC. You plug it directly into the Boardman flashing firmware and when using it in PC mode Unfortunately this doesn't do full-duplex over i2s, which is needed for a new PR in HA for XMOS chips. Their site is confusing on how to order also and they could make that much easier. I will say that with the YAML from the HA forums in the dedicated thread for this product works way better but my Wyoming satellite probably still beats it. With that said, it does seem the handle background noise is better than the S3 box does. XMOS on esp32 is very new, the firmware is still being worked out. This is a very beta product and development board, which is why there are external pads to the XIOS and XMOS chips.
@elisalantКүн бұрын
Many thanks for the info. I can’t get mine working ( on a Mac) When compiling the code from their website, I get a error, referring to the i2s Any ideas would be appreciated
@JoshFisher567Күн бұрын
@@elisalant Did you flash the i2s DFU from Seeeds wiki using the DFUtil utility? I imagine so since the esp32 is being detected in ESPHome. Without knowing the exact error/warning it's hard to say. I recommend going to the HA forums, there is a dedicated thread there for the respeaker lite. That would be the best place to post the error you are getting. It also never hurts to clean the build files and try again from scratch. Sometimes things get hosed and cleaning the build files and doing a fresh install fixes the issue. You should be able to tell what firmware it's running by plugging the board into a PC, if it shows up as an audio input/output on the PC then it needs to be flashed with the i2s firmware. It won't show up if it has the i2s firmware installed, at least not as an audio device.
@elisalantКүн бұрын
@@JoshFisher567 Many thanks Josh No, I have not flashed the firmware! That could be the issue. It does show up in ESP Home, but is always offline! Many thanks for your advice🙏
@RocketBoom1966Күн бұрын
Thanks Chris, I bought a couple of these recently. I also found the speaker to be too loud, so I used the 3.5 mm jack to connect a powered speaker that has volume control. Please inform the channel if you manage to solve you speaker volume issue.
@Emerald13Күн бұрын
I'm still confused, do I need to select the option for "with XIAO ESP32S3"? Bringing the total to ~$60?
@wscottfunkКүн бұрын
Thanks Chris! We're getting closer to a drop-in replacement for cloud based voice assistants. Exciting times! Can't wait to ditch Google!
@shanebekkerКүн бұрын
Now to test it for distance and interference. Then we can get rid of Alexa!
@SergeyKo.2 күн бұрын
Thank you for the video! Could you please tell me what hardware you use for Frigate besides Coral? What would be the best option for recording 8-10 cameras? I want to run Home Assistant and Frigate on the same computer. Would an Intel N100 be sufficient?
@Lonestar1012 күн бұрын
I'd like to see a tutorial on how to back up Home Assistant to my Synology NAS. In your video, Synology listed in your HA Backup options, but you skipped over how to set that up.
@DimusTech4 күн бұрын
I'm trying to find out some issue, when I forget my wireguard on, and I get home and connect to the home network I have no internet, anybody has an idea how to fix that?
@jameshendry35714 күн бұрын
Great video - the description in the blueprint advises that "Dynamically handle things like object type, zones, and face detection from doubletake". For those of us running Doubletake, how would you intergrate this?
@adandylife3294 күн бұрын
Thanks for clearing up the order page. I couldn't figure out which to options to pick. I'm ordering mine now.
@unfaix4 күн бұрын
2024 and I still cant figure for the life of me how to properly create a google cloud project to integrate the nest thermostat...
@abedelmajidnasser63734 күн бұрын
It just can't be more clear than that! Many thanks for your efforts and for making this video available!
@HuxleySabrina-u8l4 күн бұрын
Williams John Davis Kimberly Clark Nancy
@duotronic64515 күн бұрын
Discontinued. Replacement has fewer features. Read the reviews in their site. Not encouraging.
@TheRealAnthony_real5 күн бұрын
Just installed 14.1 .. used to have 13.1 .. nice UI however I used to run 13 behind nginx and authelia .. for some reason i can`t make it work no matter what I forward to into nginx ... or no matter of the bypass or onetime setting in authelia config .. not sure if this is now a broweser issue (usually firefox) however chrome doesn`t work either .. so the site gets the forward but i end up with a black screen .. windows or android same story .. works fine locally on both ports .. but not via cloudflare anymore .. anyone run into a similar issue ? HA works as well so I`m fine for the time being .. however if I want to log remotely via browser from outside I use my domain and I would really need that ..
@kevs90345 күн бұрын
Does this blueprint work if you have the Frigate on an LXC container on Proxmox?
@Jerry-w6y7c5 күн бұрын
Getting 402 User not authorized to perform this action when configuring Google cloud. Your video is great and right at the last step where you enter the Google CLoud Project ID it fails with this error. I have the right information entered for the Google Cloud Project ID. Have you seen this problem before or have any suggestion where I can get some help?
@Daosasone5596 күн бұрын
hi im getting oauth authorization error while obtaining access token. i followed every steps. any recommendation
@afnieves6 күн бұрын
Can you go over the setup of the alerts to avoid getting the clip errors. I have my alerts setup but still getting clips errors?
@megaveejay6 күн бұрын
Hi, Dallas seems to be replaced by one_wire in the latest ESPHome versions on HA, but I can't get it right as message is : no sensors found. Can you show me code example for one_wire?
@tboss11115 күн бұрын
I just got this working using the video as a guide; single sensor, esp32 board instead of the esp8266, I also skipped the resistor. one_wire: - platform: gpio pin: GPIO21 sensor: - platform: dallas_temp name: "temperature_dallas" update_interval: 120s
@techcoderhub6 күн бұрын
I like new one
@RocketBoom19668 күн бұрын
Thanks Chris, another well thought out video. I don't think this method works when using the Android companion app. Anyone know what's required?
@JessicaLewis-l4q8 күн бұрын
O'Kon Harbor
@ramirofdez.66309 күн бұрын
@mostlychris, thanks for this tutorial, i got some problems with error 400 (Oauth) the best way is create new project en google cloud andd create a new one on google console
@MitchVanDyke-ny4lo9 күн бұрын
Cheap way for china to bug us
@sekritskworl-sekrit_studios9 күн бұрын
Is there a way to set up a rule on your unifi system which allows you to assign the Adguard to an Alias with a set of networks?
@sekritskworl-sekrit_studios9 күн бұрын
I'm afraid something could happen to my Adguard Server. What can happen if there is a secondary to cloudflare so that it only happens if the first one dies?
@AdaCoats-c3v9 күн бұрын
Hernandez Kevin Jackson Christopher Hall Deborah
@UKsystems9 күн бұрын
Many USB cables simply do not work because you generally do not use data pairs for charging
@LesterLanders-i1i9 күн бұрын
Miller Angela Wilson Patricia Walker Daniel
@dilksvigorito9 күн бұрын
Williams Larry Davis Robert Martinez Christopher
@llablancheHermineBZH10 күн бұрын
Salut mais pour moi il est impossible de faire entre mes sensor de mon onduleur off-grid ? Ci quelqu'un la solution Merci beaucoup
@dakshkukkar215010 күн бұрын
Guys please stay away from this company, they arnt reasonable to deal with when things go wrong, the optical sensor isnt stable enough either. Please look somewhere else.
@mg329910 күн бұрын
What is coral tpu?
@ThyAnarchist8711 күн бұрын
You could still place the antenna outside the box through the side. Sure the antenna will be behind sheetrock but that's much better than the metal box its in.
@paweszumlakowski710912 күн бұрын
Unnecessary bullshit. Fuck, show it in a short and to the point video. Fuck.
@michelrochette880614 күн бұрын
Very interesting for my project. I'm looking for an approach that would allow me to operate 2 HA (Pi 4 and other) at the same time. The Pi4 would be in operation and the other system would take over in real time. In other words, the second system would take over if the first stopped working. Have you ever discussed this subject?
@Jcarlier5014 күн бұрын
how to backup on google drive ??? ( i would like to have it on local disk and on google drive) thanks
@jonirish32314 күн бұрын
How do you get to the page that you refer to (the one with the green banner)? It isn't the github repo and it doesn't appear to be the Auto Backup configuration page in HA as mine looks nothing like the one that you are showing.
@jonirish32314 күн бұрын
NM... just found it ;-)
@neilbrookins842815 күн бұрын
Dropbox not available anymore? Yes it is. I’m using it now. I get one full backup everyday into my Dropbox account. Works great.
@revealingfacts4all15 күн бұрын
All this talk of backing up with no mention or testing of restoring?
@aureliensas15 күн бұрын
thanks for the video ! How can I get the videos on Telegram and download them? Because if the computer is stolen, there's no backup.
@Tntdruid15 күн бұрын
Home Assistant Google Drive Backup does all i need.
@TismoGaming15 күн бұрын
Hear hear. Google back up is bar none the best addon I have downloaded from hacs
@BerkeleyTowers15 күн бұрын
Well, this just broke my HA...... Got to the "restart HA" bit and now can't get back into it.... 🤥
@waynenocton15 күн бұрын
Ouch. I always do a full backup then download that backup before installing anything, I’ve been burned as well.
@BerkeleyTowers15 күн бұрын
@@waynenocton Yep, I'm up and running again. My HAOS is in a Proxmox VM and I have backups for both that and the VM itself...... I was only trying this it out of curiosity.... Still not a clue what happened, but it went through without a hitch the second time........ It does look good tbf......
@waynenocton15 күн бұрын
@@BerkeleyTowers glad it worked out, and yeah weird stuff like that always happens to me, mostly when I don’t have backups lol.
@yoshidis415 күн бұрын
Great video, tnx! I was always wondering how does a full restore look like, what does it contain and how can it be done on e.g. a standalone machine.
@waynenocton15 күн бұрын
I had trouble doing restoration, thinning it was either done or hanging up during the restore. Finally I ssh’d into the box and kept checking the drive free space and realized it was actually still working, it just took far longer than I ever expected, but things worked 100% once I actually allowed it to finish. So I start a restore, and go away, or to bed lol.
@auym443215 күн бұрын
Can you go through converting the Dallas’s integration with esp home in regards to the changes to one wire
@Johnsormani16 күн бұрын
I actually flashed these to zigbee and can set everything from the mqtt addon. Esp home is just a nightmare to get working when you’re on a Mac. I always need to fire up a pc to program them. Installing drivers or not installing them, nothing helps. And that wile things like esplink work perfectly fine with the same hardware